Timeguard LEDPRORFKB Handbuch

Installation & Operating Instructions

Dedicated PIR Light

Controller c/w RF remote

control for LEDPRO

Floodlights

Model: LEDPRORFKB – Black

Model: LEDPRORFKWH – White

Model: LEDPROFOB RF Remote Fob

1. General Information

These instructions should be read carefully

and retained for further reference and maintenance.

2. Safety

• Before installation or maintenance, ensure the

mains supply to the PIR sensor is switched off

and the circuit supply fuses are removed or

the circuit breaker turned off.

• It is recommended that a qualified electrician is

consulted or used for the installation of this PIR

sensor and install in accordance with the current

IEE wiring and Building Regulations.

• Check that the total load on the circuit including

when this PIR sensor is fitted does not exceed the

rating of the circuit cable, fuse or circuit breaker.

3. Technical Specifications

PIR Light Controller

• Operating Voltage: 230V AC 50Hz

• This product is of Class I Construction and must

be earthed.

•Detection Angle: 180°

• Motion Detection Range:

Up to 12m distance at a 2.5m mounting height

• Maximum Switchable Load;

140W LED Lighting

1000W Halogen Lighting

200W CFL Lighting

500W Fluorescent tube w/o PF correction

• Time ON Adjustment: 3 seconds – 18 minutes

• Warm Up Period: Approximately 35 seconds

• Dusk (LUX) Level Adjustment: 2 – 1000 Lux

• Operating Temperature: -20°C to +40°C

• Standby (W): <0.5W

• Manual Override Mode:

ON/OFF operation using RF Remote Fob (6 fobs max)

•Sensor Head Adjustment:

Pan angle = Left/right 90°, Tilt angle = Down 150°

• RF Module: RX Receiver

• RF Frequency: 433.92MHz

•IP55 Rated suitable for restricted external applications

• CE Compliant

• Dimensions (H x W x D): 114 x 78 x 127mm

RF Remote Fob

• Battery: 3V (1x CR2032)

• Battery Life:

Approximately 24 months (@ 10x opt/day)

• Class Rating: Class III

• Transmission and Receiving Distance:

100m hand held (clear line of sight)

10m when mounted inside a wall switch

(recommended mounting height = 1.2m)

• Total number of fobs usable per PIR: 6

• Operating Temperature: -20°C to +40°C

•RF Module: TX Transmitter

• RF Frequency: 433.72MHz to 434.12MHz

• IP44 Rated suitable for restricted external

applications

• CE Compliant

• Dimensions (H x W x D): 60 x 38 x 15mm

4. Pack contents

• 1x LEDPRORFKB-WH Dedicated PIR Light Controller

c/w RF remote control for LEDPRO Floodlights

• 1x LEDPROFOB RF Remote Fob

• 1x Instruction Manual

• 1x 3V CR2032 Battery

• 1x Lens Sticker

• 2x Wire (for wall mounting a fob)

5. Selecting a Location

• The light controller has number of detection zones,

at various vertical and horizontal angles as shown

(see diagram A).

• A moving human body needs to cross/enter one

of these zones to activate the light controller.

The best all-round coverage is achieved with the

unit mounted at the optimum height of 2.5 metres.

• Careful positioning of the light controller will be

required to ensure optimum performance (see

diagram A detailing detection range and direction).

• The light controller is more sensitive to movement

ACROSS its field of vision than to movement

directly TOWARDS (see diagram B). Therefore

position the unit so that the light controller looks

ACROSS the likely approach path.

• Avoid positioning the light controller where

there are any sources of heat in the detection

area (extractor fans, tumble dryer exhausts etc.)

including opposite any other light sources such

as other security lights.

• Reflective surfaces (i.e. pools of water or white

painted walls) and overhanging branches may

cause false activation under extreme conditions.

6. Installation

6.1 Ensure the mains supply is

switched off and the circuit

supply fuses are removed or

the circuit breaker turned off.

6.2 An isolating switch should be installed

to enable the power to be switched ON & OFF

for maintenance purposes.

• During extreme weather conditions the motion

light controller may exhibit unusual behaviour.

This does not indicate a fault with the light

controller. Once normal weather conditions return,

the light controller will resume normal operation.

6.3 Remove the jumper plug from the floodlight.

6.4 Pass the 230V 50Hz mains supply and load

cables the holes provided on the PIR ensuring

that a cable gland, grommet or sealing

compound is used to maintain the IP rating.

6.5 Terminate the cables into the terminal block

ensuring correct polarity is observed and that

all bare conductors are sleeved (See section 7.

Connection Diagram).

6.6 Ensure that all connections are secure.

6.7 Connect the 3 way PIR plug, by pushing the

plug and socket inside the floodlight together

until they lock. DO NOT FORCE. THE PLUG AND

SOCKET WILL ONLY FIT TOGETHER ONE WAY

AROUND (See Jumper Plug diagram).

6.8 Secure the PIR to the floodlight using the

4 fixing screws.

7. Connection Diagram

• Connect the cables to the terminal block as follows;

• Note: The Switch Live terminal is for additional

standalone floodlights (see section 3. Technical

Specifications for maximum switchable loads).

Any floodlight connected to the L1 switch live

terminal ‘Live Output’ will be controlled by the PIR

8. Setting Up

Walk Test Procedure (Test Mode)

• The sensor will rotate from left to right, and will

tilt downwards. Adjust the light controller to point

in the required direction and angle down to limit

forward range as required.

• Set the two adjustment controls on the underside

of the unit to the following positions:

TIME ADJUST – Fully anti-clockwise

DUSK/DAWN LEVEL ADJUST – Fully clockwise

• Turn the power to the unit ON.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Timeguard Controller Handbücher

Timeguard

Timeguard SLFM360 Handbuch

Timeguard

Timeguard MLSA360N Handbuch

Timeguard

Timeguard PDFM1500N Handbuch

Timeguard

Timeguard RTS113Q Programmierhandbuch

Timeguard

Timeguard SLDD1000 Handbuch

Timeguard

Timeguard TLRX05 Handbuch

Timeguard

Timeguard PDSM1500 Handbuch

Timeguard

Timeguard ProgramaSTAT UFPT24 Bedienungsanleitung

Timeguard

Timeguard TS900N Montageanleitung

Timeguard

Timeguard NSLDD1000 Handbuch

Timeguard

Timeguard SLB2300RF Handbuch

Timeguard

Timeguard SLW360L Handbuch

Timeguard

Timeguard MLB3000 Handbuch

Timeguard

Timeguard SLFM360N Handbuch

Timeguard

Timeguard PDWM1500 Handbuch

Timeguard

Timeguard TS900B Bedienungsanleitung

Timeguard

Timeguard TRT039N Handbuch

Timeguard

Timeguard SLFM360L Handbuch

Timeguard

Timeguard SLB2300 Handbuch

Timeguard

Timeguard RTS113 Programmierhandbuch

Timeguard

Timeguard E269H-Synchronous Handbuch

Timeguard

Timeguard MTLW3000 Handbuch

Timeguard

Timeguard PDRS1500N Montageanleitung

Timeguard

Timeguard PDFMMINIL Handbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung