Timeguard SLB2300 Handbuch

Installation & Operating Instructions

2300W PIR Light Controller

Model: SLB2300 – Black

Model: SLW2300 – White

1. General Information

These instructions should be read carefully and retained for further reference

and maintenance.

2. Safety

• Before installation or maintenance, ensure the mains supply to the

PIR sensor is switched off and the circuit supply fuses are removed

or the circuit breaker turned off.

• It is recommended that a qualified electrician is consulted or used for

the installation of this PIR sensor and install in accordance with the

current IEE wiring and Building Regulations.

• Check that the total load on the circuit including when this PIR

sensor is fitted does not exceed the rating of the circuit cable,

fuse or circuit breaker.

3. Technical Specifications

• 230V AC 50 Hz

• This PIR is of Class l construction and should be earthed

• Motion Detection Range: Up to 12m at 2.5m mounting height

• Detection Angle: 180°

• Maximum Switching Load: 2300W Halogen Lighting

500W Fluorescent Lighting

250W LED Lighting (PF>=0.9)

• Not suitable for use with Discharge Lighting

• Time ON Adjustment: 5 seconds to 15 minutes

• Dusk Level Adjustment: Day & Night or Night time only operation

• Operating Temperature: -20°C to +40°C

• IP55 Rated suitable for restricted external applications

• CE Compliant

4. Introduction

The SLB/W2300 utilises passive infrared technology to detect heat radiation

of moving human bodies. Upon detection, the attached lighting load will

illuminate for a user-determined period of time. An integral daylight sensor

ensures all day or night-only operation.

5. Selecting a Location

• The motion detector has number of detection zones, at various vertical

and horizontal angles as shown (see diagram A).

• A moving human body needs to cross/enter one of these zones to activate

the sensor. The best all-round coverage is achieved with the unit mounted

at the optimum height of 3 metres.

• Careful positioning of the sensor will be required to ensure optimum

performance (see diagram A detailing detection range and direction).

• The sensor is more sensitive to movement ACROSS its ﬁeld of vision

than to movement directly TOWARDS (see diagram B). Therefore position

the unit so that the sensor looks ACROSS the likely approach path.

• Avoid positioning the sensor where there are any sources of heat

in the detection area (extractor fans, tumble dryer exhausts etc.)

including opposite any other light sources such as other security lights.

• Reﬂective surfaces (i.e. pools of water or white painted walls)

and overhanging branches may cause false activation under

extreme conditions.

• During extreme weather conditions the motion sensor may exhibit

unusual behaviour. This does not indicate a fault with the sensor.

Once normal weather conditions return, the sensor will resume

normal operation.

6. Installation

• An isolating switch should be installed to the switch the power ON & OFF.

This allows the sensor to be easily switched OFF when not required for

maintenance purposes.

• Remove the back plate from the PIR sensor (see diagram F).

• Mark the position of the ﬁtting holes. Drill the holes. Insert the rawl

plugs into the holes.

• Pass the supply cable through the cable entry point on the back plate,

ensuring the grommet(s) is used to maintain the IP rating of the

PIR sensor.

• Fix the back plate to the wall. Take care not to over-tighten the screws

to prevent damage to the back plate. If using a power screwdriver,

use the lowest torque setting

• Terminate the cable into the terminal block ensuring correct polarity

is observed and that all bare conductors are sleeved (see below details

on connection).

7. Connection

Connect the mains supply cable to the terminal block on the back plate

as follows (see connection diagram E):

NEUTRAL (Blue) N

EARTH (Green/Yellow)

LIVE (Brown) L

Connect the cable from the lighting load to the terminal block on the

backplate as follows;

EARTH (Green/Yellow)

NEUTRAL (Blue) N

SWITCH LIVE (Brown) L1

Ensure all connections are secure.

Line the unit up with the back plate, apply pressure to both sides of the unit

until both catches click into place to ensure a weatherproof seal.

8. Setting Up

Walk Test Procedure

• The sensor will rotate from left to right, and tilt up or down. Adjust the

sensor to point in the required direction and angle down to limit forward

range as required.

• Set the two adjustment controls on the underside of the unit

(see diagram C) to the following positions:

TIME – Fully anti-clockwise

DUSK – Fully clockwise.

• Turn the power to the unit on. The lamp will illuminate for approximately

35 seconds. This indicates the unit is wired correctly. The unit is in

Automatic Mode when the light turns off.

• If the detection area is too small for your requirements, try angling the

sensor head up. This will increase the detection area. Angling the head

downwards will reduce the detection area should a smaller coverage

be required.

Setting Up for Automatic Operation

• When walk tests are complete, the unit can be adjusted for automatic

operation:

The TIME setting controls how long the unit remains illuminated following

activation & after all motion ceases. (See diagram C, the time adjustment

knob is indicated by the ‘Clock’ symbol).

• The minimum time (fully anti-clockwise) is approx. 5 seconds, whilst the

maximum time (fully clockwise) is approximately 15 minutes.

• Set the control to the desired setting between these limits.

• The DUSK control determines the level of darkness required for the unit to

start operating (see diagram C). The DUSK adjustment knob is indicated

by the ‘Moon’ and ‘Sun’ symbols).

• Set the light threshold to maximum (fully clockwise/Sun end), then turn

the control anti-clockwise about three quarters of the way round to the

Moon end. This will give operation after DUSK approximately.

If you experience problems, do not immediately return the unit

to the store. Telephone the Timeguard Customer Helpline;

HELPLINE

020 8450 0515

• For a more accurate setting of the DUSK control turn it fully anti-clockwise

(Moon end) and leave for at least 20 seconds for the unit to settle.

• When the ambient light level reaches that required for DUSK, adjust the

DUSK control a small amount clockwise pausing to try to get the unit

to detect and turn the lights under control ON by moving a hand

slowly backwards and forwards across the front of the detector lens

for around 5 seconds.

• Continue to turn the control small amounts in a clockwise direction,

stopping after each adjustment to try to get the unit to detect as above.

• Eventually detection will occur and the DUSK level is now set as required.

9. Masking the Sensor Lens

• To reduce the sensor coverage, preventing detection in unwanted areas,

mask the sensor lens using the lens mask sticker supplied (see diagram D).

• The top section of the lens covers long range detection, the bottom covers

short range. Similarly the left and right lens sections cover the left and

right detection area respectively.

• Mask the sensor to suit your installation.

10. Manual Override Mode

• The light can be switched ON for longer time periods by use of the

Manual Override Mode. This can be activated at night time (only) by using

the internal wall switch or circuit breaker. Switch the internal wall switch

once (OFF/ON) within 1.5 seconds.

• The unit will now illuminate continuously for 6 hours or until

it is switched back into Auto Mode.

• To return to Auto Mode, switch the internal wall switch OFF

and then back ON again within 1.5 seconds.

• The unit will return to its Auto Mode and will operate as set up

after the walk test procedure.

8 9

11. Accessing Terminals

After Installation

• This may be necessary to add further lighting for instance and the

following procedure for removing the unit from its backplate should

be followed:-

• Insert a ﬂat blade screwdriver in the catch at the sides of the unit

and lever it outwards (as indicated in diagram F, Step 1).

• The terminals are now accessible. If adding lighting, ensure the unit’s

rating is not exceeded.

12. Troubleshooting Guide

Problem

• Lamp stays ON

all the time

night and day.

• Lamp stays ON all

the time at night,

or PIR keeps activating

at random for no

apparent reason.

Solution

Check wiring connections.

Wires to L and L1terminals may be transposed.

The unit may be suffering from false activation.

Cover the sensor lens completely with black

pvc tape. This will prevent the sensor from

‘seeing’ anything. If the unit now switches

off after the set time duration and does not

re-activate, this indicated that the problem was

caused by false activation. The problem may be

solved by slightly adjusting the direction/angle

of the sensor head (see section 8. Setting up).

If however, the unit continues to remain ON

or to operate randomly then the unit is faulty

and should be replaced.

You may not be allowing the unit time to

complete its warm-up period. Stand well out

of the detection range and wait (the warm-up

period should never exceed 5 minutes).

Occasionally, winds may activate the sensor.

Sometimes passages between buildings etc.

can cause a ‘wind tunnel’ effect.

Ensure the unit is not positioned so as to

allow detection of cars/people using public

thoroughfares adjacent to your property.

Ensure that the unit is mounted securely,

even the slightest movement can result in

a false detection.

Check that the power is switched ON at the

circuit breaker/internal wall switch.

Turn OFF the power to the unit and check the

wiring connections as per the diagram

(see 7. Connection).

Ensure no connections are loose.

Check the bulb (if it’s replaceable).

If the bulb has failed, replace (do not hold the

bulb directly with ﬁngers, use a tissue or clean

dry cloth). Ensure the bulb is seated correctly

in the bulb holder.

Refer to section 8. Setting Up for DUSK

control adjustment.

Refer to section 8. Setting Up for DUSK

control adjustment.

Unit may be poorly located. See Section 5.

Selecting a Location and re-locate the unit.

PIR sensors are inﬂuenced by climatic conditions.

The colder the ambient temperature, the more

effective the sensor will be. You may need to

make seasonal adjustments to the sensor head

position to ensure trouble-free operation all

year round.

• PIR sensor will not

operate at all.

• PIR sensor will not

operate at night.

• Unit activates during

the daytime

• PIR coverage is

poor/sporadic

• Detection range

varies from day

to day.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Timeguard Controller Handbücher

Timeguard

Timeguard RTS113Q Programmierhandbuch

Timeguard

Timeguard PDFMMINIL Handbuch

Timeguard

Timeguard SLDD1000 Handbuch

Timeguard

Timeguard PDFM1500 Handbuch

Timeguard

Timeguard TLRX05 Handbuch

Timeguard

Timeguard LEDPRORFKB Handbuch

Timeguard

Timeguard SLB2300RF Handbuch

Timeguard

Timeguard ELU56 Handbuch

Timeguard

Timeguard NSLDD1000 Handbuch

Timeguard

Timeguard TRT039N Handbuch

Timeguard

Timeguard ProgramaSTAT UFPT24 Bedienungsanleitung

Timeguard

Timeguard TS900B Bedienungsanleitung

Timeguard

Timeguard SLFM360 Handbuch

Timeguard

Timeguard E269H-Synchronous Handbuch

Timeguard

Timeguard SureTime STLW1000 Handbuch

Timeguard

Timeguard MLB3000 Handbuch

Timeguard

Timeguard PDRS1500N Montageanleitung

Timeguard

Timeguard PDFM1500N Handbuch

Timeguard

Timeguard PDWM1500 Handbuch

Timeguard

Timeguard TS900N Montageanleitung

Timeguard

Timeguard SLW360N Handbuch

Timeguard

Timeguard MTLW3000 Handbuch

Timeguard

Timeguard SLB2300RF Handbuch

Timeguard

Timeguard TRTD7N Handbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung