Tiso BASTION-M Bedienungsanleitung
SERVO-OPERATED TRIPOD TURNSTILES
CENTURION-M
BASTION-M
SKULL-M
TWIX-M
OPERATION MANUAL
2018
“TiSO-PRODUCTION” LTD
CONTENTS
INTRODUCTION................................................................................................................................................... 3
1. DESCRIPTION AND OPERATION.................................................................................................................. 6
1.1 General Information and Purpose............................................................................................................. 6
1.2 Specifications............................................................................................................................................7
1.3 Configuration and Scope of Delivery....................................................................................................... 7
1.4 Design and Operation .............................................................................................................................10
1.5 Instrumentation, tools and accessories................................................................................................... .13
1.6 Description and operation of controllers as components of the turnstile.............................................. .14
2. INTENDED USE................................................................................................................................................24
2.1 Operation restrictions...............................................................................................................................24
2.2 Layout and installation. ........................................................................................................................... 24
2.3 Preparation for use .................................................................................................................................... 32
2.4 Contingency actions.................................................................................................................................. 34
3. MAINTENANCE................................................................................................................................................ 34
3.1 General guidelines.................................................................................................................................... 34
3.2 Safety measures........................................................................................................................................ 35
3.3 Maintenance procedure............................................................................................................................. 35
4. ROUTINE MAINTENANCE.............................................................................................................................36
4.1 General guidelines....................................................................................................................................36
4.2 Troubleshooting........................................................................................................................................36
4.3 Postrepair checkout................................................................................................................................... 38
5. TRANSPORTATION AND STORAGE....... ..................................................................................................... 39
5.1 Turnstile storage....................................................................................................................................... 39
5.2 Turnstile transportation.............................................................................................................................39
6. DISPOSAL........................................................................................................................................................ .39
7. MANUFACTURER’S WARRANTY AND TERMS OF WARRANTY MAINTENANCE............................39
Annex А....................................................................................................................................................................41
Annex B: Control panel and connection diagram....................................................................................................45
Annex C: Wiring diagram of the servo-operated tripod type turnstile.................................................................. 47
Annex D 1: Wiring diagram of the turnstile connection to access control system (ACS) in pulse mode...............48
Annex D 2: Wiring diagram of the turnstile connection to access control system (ACS) in hold mode................. 49
Annex D 5: Diagram of the turnstile connection to control panel.............................................................................52
Design, overall and installation dimensions of the "BASTION-M" type turnstile..................................................42
Design, overall and installation dimensions of the "SKULL-M" type turnstile.......................................................43
Design, overall and installation dimensions of the "TWIX-M" type turnstile.........................................................44
Annex D 3: Wiring diagram of the turnstile connection to fire alarm system (FAS)...............................................50
Annex D 4: Wiring diagram of the turnstile connection to fire alarm system (FAS)............................................... 51
Design, overall and installation dimensions of the "СENTURION-M" type turnstile.............................................41
3
T3. XXX. X X
Waist-high turnstile
Т3
TCC
О without antipanic device
Е with antipanic device
М with electromechanical
antipanic device
TCY
S Brushed stainless steel
P Polished stainless steel
K Painted body
TCG
TYK
INTRODUCTION
This Operation Manual (hereinafter referred to as OM) covers the servo-operated turnstile
(hereinafter referred to as the "turnstile"). The Operation Manual contains information about design,
specifications, installation for proper operation and maintenance of the turnstile.
This Operation Manual is prepared in compliance with the specification requirements ТY
Y 31.6-32421280-004:2010.
The turnstile shall be serviced only by the qualified staff having the relevant class of permit to work
with electrical facilities with voltage up to 1000 V and scrutinizing this Operation Manual, obtaining
safety instructions and trained for operation and maintenance of the turnstile.
Reliability and durability of the turnstile operation is provided with observation of modes and
conditions of transportation, storage, installation and operation. So, fulfillment of all requirements
specified in this document is mandatory.
Depending on the turnstile purpose and design features, the following pattern of reference
designation is accepted:
Due to regular improvement of the product its design can be modified without degradation of
the product features and quality not covered by this Operation Manual.
Servo-operated
solid body tripod
(3 barrier rods)
Servo-operated
one-piece elongated body
tripod (3 barrier rods)
Servo-operated
head body tripod
(3 barrier rods)
Servo-operated
corner body tripod
(3 barrier rods)
4
The tripod type turnstile reference designation is given in Table 1.
Table 1
Name Code Designation
CENTURION-M
T3.TCC.ХE
AUIA.095 OM
BASTION-M
T3.TCY.ХE
AUIA.097 OM
SKULL-M
T3.TCG.ХE
AUIA.096 OM
TWIX-M
T3.TYK.ХE
AUIA.137 OM
Example of reference designation of the servo-operated turnstile with solid body of brushed
stainless steel when the turnstile T3.ТСC.SE ТY Y 31.6-32421280-004:2010 is ordered.
5
WARNINGS TO THE CUSTOMER
ON SAFE OPERATION OF THE TURNSTILE
These warnings are designed for ensuring of safety during operation of the turnstile to prevent
violation of safety characteristics by improper installation or operation. These warnings are aimed
at drawing attention of the customer to safety problems.
GENERAL WARNINGS
The Operation Manual is an integral part of the product and it shall be handed over to the
customer. The OM shall be kept for future use and consulted for clarifications if required. If the
turnstile is resold, handed over to another owner or transported to another place, make sure that
the OM is enclosed to the turnstile to be used by new owner and/or maintenance staff during
installation and/or operation.
Safety measures and requirements specified in this OM must be observed:
–the turnstile must be connected to ground loop prior to operation;
–the turnstile to be connected to AC network with parameters specified in paragraph 1.2
"Specifications";
–inspection, adjustment and repair should be performed only after the turnstile is
deenergized.
After purchasing of the turnstile it should be unpacked and its integrity should be checked. In
case of doubt in integrity of the turnstile it should not be used and the customer should refer to
the supplier or to the manufacturer.
Packing accessories (wooden pallet, nails, clips, polyethylene bags, cardboard etc.) as potential
sources of hazard must be removed to unacceptable place prior to proper use of the turnstile.
As electric shock protection device the turnstile is related to 01 protection class according to
GOST (State Standard) 12.2.007.0-75 and is not intended for operation in explosive and fire-
hazardous areas by the "Rules for design of electrical installations".
Using of the turnstile for unintended purpose, improper installation, nonobservance of conditions
of transportation, storage, installation and operation, specified by this OM, may result in damage
to people, animals or property for which the manufacturer is not responsible.
6
1. DESCRIPTION AND OPERATION
1.1 General Information and Purpose
1.1.1 Turnstile purpose:
1.1.2 The turnstile dimensions and weight correspond to the values specified in Table 2.
Table 2
Designation of
modification
Dimensions, mm Pedestal size,
(LхW), m
Max.weight,
kg
Height Length Width
T3.TCC.XE
1000
793
847
324х332
40
T3.TCY.ХE
1000
793
815
524х300
40
T3.TCG.ХE
616
793
833
524х300
30
T3.TYK.ХE
1000
1000
785
1004х270
80
1.1.3 The operation condition parameters according to GOST 15150-69 are specified in
Table 3.
Table 3
Operation
conditions
Ambient air temperature
MC4
+1°С to +40°С
Relative air humidity
Ambient air allowable pressure
Transportation temperature range
Storage temperature range
Group of mechanical application
L3
Altitude above sea level up to 2000 m
Environment MC4
Explosion-proof, does not contain
current-conducting dust, aggressive
gases and vapours in concentration
destroying isolation and metals,
The turnstile is designed for arrangement of individual pedestrian access at access points of
industrial enterprises, banks, stadiums, administrative facilities etc. driven by control signals of
access control system (from keypad, proximity card readers) or manually (from wire control
panel).
For climatic
modification Parameter value
80 % at 20 ºС
84 to 106,7kPa
- 40°С to + 50°С
+ 5°С to + 40°С
7
Continued Table 3
1
2
3
disturbing normal operation of the
equipment installed in turnstiles
Installation site
In enclosed spaces in the absence of
direct impact of precipitations and
solar radiation
Operating position
Vertical, deviation from vertical
position no more than 1º to any side
is acceptable
1.1.5 Reliability indices:
– mean time to repair (without delivery time of spare parts, tools and accessories) – at most
6 hours;
– mean time to failure – at least 1 500 000 accesses;
– mean service life between overhauls – at least 10 years.
1.2 Specifications
The key parameters of the turnstile are specified in Table 4.
Table 4
Parameter description Unit measure Parameter
value
Minimum traffic flow capacity in free access mode man/min.
60
Minimum traffic flow capacity in single access mode man/min.
25
Maximum access way width mm 600 mm
Power supply voltage:
–
AC power supply (primary) V
Hz
100 240
~ 50/60
–
DC power supply (secondary) V
12
Maximum power consumption W
55
Index of protection according to EN 60529
-
IP41*
1.3 Configuration and Scope of Delivery
1.3.1 The servo-operated waist-high turnstile design includes the following key
devices and components (See Fig.1):
Design, overall and installation dimensions of the turnstile are shown in Annex A.
8
Fig. 1 – Turnstile general appearance
The turnstile modifications are manufactured from:
– polished stainless steel (reference designation T3.TCC.PE).
– brushed stainless steel (reference designation T3.TCC.SE).
– carbon steel painted in any colour according to RAL (reference designation T3.TCC.КE);
The turnstile basic modification is made of brushed stainless steel.
CENTURION-M
BASTION-M
SKULL-M
TWIX-M
1 - turnstile rack;
2 - LED display;
3 - card reader location;
4 - upper lid;
5 - control mechanism;
6 - hub;
7 - barrier rod;
8 - lock door;
9 - control panel;
10 - footing.
9
1.3.2 Turnstile scope of delivery
(standard):
Tripod turnstile
Control panel
Anchors
(4 pcs.)
Data sheet
Battery (capacity 4 Ah)1
For
convenience
of
delivery
the
turnstile
is
supplied
ready-to-install
with
dismounted barrier rods
(See Fig.2).
Fig.2. – Tripod turnstile scope of delivery
1.3.3 The turnstile design, overall and installation dimensions (See Fig.3)
Fig. 3 - Tripod turnstile dimensions
1 Is not included in the turnstile scope of delivery - to be equipped by the custoner, if appropriate
CENTURION-MBASTION-M
SKULL-M
*Carrier sleeve size
TWIX-M
Turnstile assembly
Hub with barrier rods
10
1.4 Design and operation
1.4.1 Turnstile design
1.4.1.1 The turnstile body is a metalware, which footing 10 (See Fig.1) is installed on an even
surface by means of Redibolt anchors. The turnstile status is displayed by LED display boards 2,
built in the turnstile body. The turnstile initial state is indicated by constantly lit red LED (See
Fig.4): the turnstile access is locked in both directions.
Fig. 4 - Turnstile status LED display
1.4.1.2 The control mechanism 5 (See Fig.1) is installed at the top of the body. The hub 6 with
barrier rods 7, securely fixed to its levers by crimping method, is installed on the control
mechanism shaft. One of three barrier rods is positioned horizontally barring the turnstile access.
1.4.1.3 The plates, on which power supply unit, controllers, terminal blocks for connection to 220
V network and control panel are mounted, are fixed inside the turnstile post 1 (See Fig.1) under the
removable door 8 (for the turnstiles CENTURION-M and BASTION-M) or removable lid 4 (for
the turnstiles TWIX and SKULL). Controller controls the turnstile motor analyzing signals from
speed and position sensors as well as provides the motor protection against overloads. Receiving
control commands from peripherals (control panel, ACS etc.) the controller controls LED displays
and generates feedback signals for ACS (Access Control System).
1.4.1.4 The external control panel (See Annex B) has the following functions: single entry access,
single exit access; entry locking, exit locking; free entry access, free exit access, panic.
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
