Topcom Babytalker 1010 Bedienungsanleitung

PMR BABYTALKER 1010

USER GUIDE

V 1.1

UK The features described in this manual are published with reservation to

modifications.

UK The CE symbol indicates that the unit complies with the essential requirements of

the R&TTE directive.

This product is in compliance with the essential requirements and other relevant provisions of the R&TTE directive 1999/5/EC.

The Declaration of conformity can be found on :

http://www.topcom.net/support/cedeclarations.php

2. 3.

SCAN

VOX

TX RX

2TOPCOM Babytalker 1010

TOPCOM Babytalker 1010

1 Introduction

Thank you for purchasing the Babytalker 1010. It’s a short range (up to 2 km in open field),

low powered babyphone base station in combination with a 446 MHz PMR (Pivate Mobile

Radio). The Babytalker 1010 can be used in any country where the service is authorised as

indicated on the packing box and in this manual

2 Intended purpose

The Babytalker 1010 can be used to keep in contact with your baby or to monitor any audible

activity in a room from a longer distance (up to 2 km in open field).

The selectable VOX sentivity ensures you that every sound in the baby’s room is clearly

received.

3 CE Mark en restrictions

The CE symbol on the unit, user guide and giftbox indicates that the unit complies with the

essential requirements of the R&TTE directive 1995/5/EC.

The ! symbol next to the CE mark, indicates that the PMR standard is not allowed in all

European countries.

PMR is allowed in the next countries:

Belgium, Holland, Germany, Sweden, Denmark, Norway, Finland, Spain, Italy, Portugal,

Greece, Czech, Luxemburg, Hungary, Slovakia, Suisse, France, UK, Ireland, Austria, Poland

4 Safety instructions

4.1 General

Please read carefully through the following information concerning safety and proper use.

Make yourself familiar with all functions of the device. Keep this manual on a safe place for

future use.

4.2 Babies safety

• The Babytalker 1010 is not a substitute for responsible and proper adult supervision and

should not be used as such.

• Make sure the Baby Unit and adapter cable are always out of reach of the baby, at least

one metre away.

• Never place the Baby Unit inside the baby ’s bed or playpen!

• Never cover the baby monitor (with a towel, blanket, etc.).

Restriction:

Check the local regulations before using it outside the

country where it was purchased. The standard may be

prohibited in this country.

TOPCOM Babytalker 1010 3

TOPCOM Babytalker 1010

ENGLISH

4.3Burning injuries

•Ifthe cover ofthe antennais damaged, do not touch because when an antennacomes

in contact with the skin, aminor burn may result when transmitting.

•Batteries can cause property damage such as burns ifconductive material such as

jewellery, keys or beaded chains touches exposed terminals.The material may complete

an electrical circuit (short circuit) and become quite hot. Exercise care in handlingany

charged battery, particularly when placingit inside apocket, purse or other container

with metal objects.

4.4 Injuries

• Do not place your device in the areaover an air bag or in the air bag deployment area.

Air bags inflate with great force. IfaPMR is placed in the bag deployment areaand the

air bag inflates, the communicator may be propelled with great force and cause serious

injury to the occupants ofthe vehicle.

• Keep the PMR at least 15 centimetres away fromapacemaker.

• Turn your PMR OFF as soon as interference is takingplace with medical equipment.

4.5 Danger of explosion

• Do not replace batteries in apotentially explosive atmosphere. Contact sparkingmay

occur while installingor removingbatteries and cause an explosion.

• Turn your PMR off when in any areawith apotentially explosive atmosphere. Sparks in

such areas could cause an explosion or fire resultingin bodily injury or even death.

• Never throwbatteries in fire as they may explode.

4.6 Poisoning danger

• Keep batteries away fromsmall children

Areas with potentially explosive atmospheres are often, but not always,

clearly marked. They include fuelling areas such as below deck on

boats, fuel or chemical transfer or storage facilities; areas where the air

contains chemicals or particles, such as grain, dust or metal powders;

and any other areawhere you would normally be advised to turn off your

vehicle engine.

4TOPCOM Babytalker 1010

TOPCOM Babytalker 1010

4.7 Legal

• Turn your PMR OFF in any facilities where posted notices instruct you to do so.

Hospitals or health care facilities may be usingequipment that is sensitive to external RF

energy.

• Replacingor modifyingthe antennamay affect the PMR radio specifications and violate

the CE regulations. Unauthorised antennas could also damage the radio.

4.8 Notes

• Do not touch the antennawhile transmitting, it could affect the range.

•Remove the battery ifthe device is not goingto be used for alongperiod.

5Cleaning and maintenance

• To clean the unit, wipe with asoft cloth dampened with water. Don’t use acleaner or

solvents on the unit; they can damage the case and leak inside, causingpermanent

damage.

•Battery contacts may be wiped with adry lint-free cloth.

•Ifthe unit gets wet, turn it off and remove the batteries immediately. Dry the battery

compartment with asoft cloth to minimize potential water damage. Leave the cover off

the battery compartment overnight or until completely dry. Do not use the unit until

completely dry.

6 Disposal of the device (environment)

At the end ofthe product lifecycle, you should not throwthis product into the

normal household garbage but bringthe product to acollection point for the

recyclingofelectrical and electronic equipments. The symbol on the product,

user guide and/or box indicate this.

Some ofthe product materials can be re-used ifyou bringthemto arecyclingpoint. By re-

usingsome parts or raw materials fromused products you make an important contribution to

the protection ofthe environment. Please contact your local authorities in case you need

more information on the collection points in your area.

Dispose of batteries at adesignated battery disposal unit and not in

the household waste.

TOPCOM Babytalker 1010 5

TOPCOM Babytalker 1010

ENGLISH

7 Using the Babytalker 1010

To have communication between the Babyphone and the PMR device they need to be set

both on the same channel and within receivingrange (up to max. 2km in open field). Since

these devices use free frequency bands (channels), all devices in operation share these

channels (total 8 channels). Therefore, privacy is not garanteed.

The babytalker opererates on VOX mode. This means that the device starts sendingas soon

as the microphone detects sound. The sensitivity ofthe sound detection can be changed by

the user.

Any other PMR device in range , on the same channel and in standby mode (not transmitting)

will hear the transmitted signal.

8Included in the package

•1xBaby Unit

•1xParent unit

• 1 x Beltclip

• 1 x Power adapter

• 1 x Charger

• 1 x Battery pack

•Userguide

Speaking fromaPMR unit to the babyphone is not possible to

prevent unknown persons to disturb the babies night rest.

6TOPCOM Babytalker 1010

TOPCOM Babytalker 1010

9Installation

9.1 Baby unit

9.1.1 Using the power adapter

Plugone end ofthe adaptor (DC 10V/

300mA) into the power outlet and the

other end into the adapter jackon the

side ofthe baby unit . Aclick

indicates, the jackis locked into

position.

9.1.2 Using batteries

Instead ofusingthe power adapter, the baby unit can be powered by ‘LR03’ Alkaline (non-

rechargeable) batteries.

1 Pull the battery cover tab and gently remove the battery cover.

2Install 4 ‘AAA’ ‘LR03’ alkaline batteries followingthe polarity as shown.

3 Re-install the Battery Cover

The Baby unit can operate with power adapter OR with non-

rechargeable ‘LR03’ alkaline batteries. It has no charging function.

The Parent unit can operate with rechargeable or LR03’ alcaline

batteries (not included).

1 x AAA

TOPCOM Babytalker 1010 7

TOPCOM Babytalker 1010

ENGLISH

9.2 Parent unit

9.2.3 Recharging batteries

With the enclosed rechargeable battery packor 3 x AAA NiMh rechargeable batteries (not

supplied) installed, the batteries can be charged with the included charger(DC 7,5V/

200mA).

9.2.1 Removing/Installing the Belt Clip

1 To remove the clip fromthe unit, push

the belt clip (B) towards the antenna,

while pullingthe belt clip tab away from

the unit (A).

2When re-installingthe belt clip, aclick

indicates the Belt Clip is locked into

position.

9.2.2 Battery Installation

1Remove the belt clip (See chapter

9.2.1 ).

2Pull the battery door tab down (C) and

slide the battery cover away fromthe

antenna. (D)

3 Install the rechargeable battery pack

followingthe polarity as shown. Ensure

that the metal contacts on the site are

facingoutwards fromthe radio to

connect on the battery door.(E)

4 Re-install the Battery Cover and Belt

Clip (See chapter 9.2.1 ).

Note: Instead ofthe supplied battery pack, the

PMR can be used with 3xAAA NiMh batteries.

Followthe polarity as shown in the battery

compartment when installing.

Only use the included AC/DC ADAPTER with “AAA” rechargeable

batteries. Do not charge this unit when regular “AAA” ‘LR03’ alkaline

batteries are installed.

Do not connect other chargers. This may damage your device.

8TOPCOM Babytalker 1010

TOPCOM Babytalker 1010

•Plugthe small plugofthe adapter into the charger jack

on the top ofthe unit and the other end in the electrical

socket.

•Make sure that the unit is switched off in order to charge

the batteries properly.

NOTE: It takes approximately 12 to 14 hours to fully

charge the batteries (with 600mAh).

10 Supporting device for wall assembly

The baby unit is wall mountable. The appropriate screwis not supplied. Turn a3mm screw

into the wall. The screwhead must be approx. 3 mm out ofthe wall so that the screwcan be

fixed correctly into the hanghole at the backofthe baby unit. Hangthe baby unit with its

hanghole carefully to this screw.

11 Battery Charge Level

The BATTERY CHARGE LEVEL in the Parent Unit, as well as in the Baby Unit is indicated

by the number ofsquares present inside the BATTERY icon on the LCD Display.

• Battery Full

• Battery 2/3 charged

• Battery 1/3 charged

• Battery empty

12 Buttons

12.1 Baby unit

(See picture 1 on the folded cover page)

1VOXsensitivity control

2Microphone

3 On/Off switch

4 Menu down button: Select the previous value in the menu.

5 External microphone connector (microphone not included)

6Menu button: Enter the setting menu

7Power adapter connector

8 Menu up button - Select the next value in the menu.

9 LCD display

10 Hanghole for wall mounting

11 ON/OFF LED

TOPCOM Babytalker 1010 9

TOPCOM Babytalker 1010

ENGLISH

12.2 Parent unit

(See picture 2on the folded cover page)

12Charger connector

13 LCD display

14 Call button

15 Menu button - Enter the setting menu

16Speaker

17 Microphone

18 Menu down button

– Decrease the speaker volume

– Select the previous value in the menu.

19 Menu up button

– Select the next value in the menu.

– Increase the speaker volume

20 Push to talkbutton

21 On/Off Button

22 Lockbutton

23Antenna

13LCD Display information

13.1 Baby unit

(See picture 3 on the folded cover page)

ACall Tones icon

BChannel indicator

CAuto monitor function icon

D Beep tone function icon

EBattery level indicator

FPower adapter connected icon

GChannel Memory indicator

HTranmission icon

IChannel/Memory channel number

13.2 Parent unit

(See picture 4 on the folded cover page)

aReceive icon

bChannel/Memory channel number

cKeypad lockicon

dSpeaker volume

eBattery level indicator

fChannel Memory indicator

gVOXicon

hSCAN icon

iTransmission icon

10 TOPCOM Babytalker 1010

TOPCOM Babytalker 1010

14 Turning the Babytalker 1010 ON/OFF

14.1 Baby unit

14.2 Parent unit

15 Setting the Channel Memory

To have communication between the Baby Unit and the Parent unit they need to be set both

on the same channel memory. 15 Channel Memories are available (See chapter 23).

15.1 Baby unit

To turn ON:

•Set the On/Off switch to the top position (I), the LCD display

will showthe current channel or memory location.

To switch OFF

•Set the On/Off switch to the bottomposition (O), the LCD

display will turn blank.

To turn ON:

• Press and hold the - button . The unit will “beep” and the

LCD display will display the current channel.

To switch OFF

• Press and hold the - button . The unit will “beep” and the

LCD display will turn blank.

• Press the - button twice, the current channel memory

flashes on the display.

• Press the - button or the - button to change the

channel memory.

To disactivate the Channel Memory function, select OF

• The unit will return to standby ifno button is pressed within 5

seconds.

Any PMR set on the corresponding channel can receive and listen to

the conversation.

Andere Handbücher für Babytalker 1010

Inhaltsverzeichnis

Andere Topcom Babyphone Handbücher

Topcom

Topcom BABYTALKER 2500 Bedienungsanleitung

Topcom

Topcom BABY VIEWER 2500 Bedienungsanleitung

Topcom

Topcom BABYTALKER 1020 Bedienungsanleitung

Topcom

Topcom BABYVIEWER KS-4248 Bedienungsanleitung

Topcom

Topcom BABYTALKER 1020 Bedienungsanleitung

Topcom

Topcom Babytalker PMR 1010 Bedienungsanleitung

Topcom

Topcom Babyviewer 4100 Bedienungsanleitung

Topcom

Topcom BABYTALKER 3000 SEDS Bedienungsanleitung

Topcom

Topcom BABYTALKER 3100 Bedienungsanleitung

Topcom

Topcom Babytalker PMR 1010 Bedienungsanleitung

Topcom

Topcom BABYTALKER 1020 Bedienungsanleitung

Topcom

Topcom BABYVIEWER KS-4240 Bedienungsanleitung

Topcom

Topcom KS-4245 Bedienungsanleitung

Topcom

Topcom Babytalker 3600 Bedienungsanleitung

Topcom

Topcom BABYVIEWER 4500 Bedienungsanleitung

Topcom

Topcom KS-4216 Bedienungsanleitung

Topcom

Topcom BABYTALKER 3500 SEDS Bedienungsanleitung

Topcom

Topcom BABYVIEWER 4500 Bedienungsanleitung

Topcom

Topcom BABYVIEWER 4400 Bedienungsanleitung

Topcom

Topcom babytalker KS-4221 Bedienungsanleitung

Topcom

Topcom BABYTALKER 1020 Bedienungsanleitung

Topcom

Topcom BPM WRIST 2000 Bedienungsanleitung

Topcom

Topcom BABYTALKER 2100 Bedienungsanleitung

Topcom

Topcom BABYVIEWER KS-4246 Bedienungsanleitung

Beliebte Babyphone Handbücher anderer Marken

Philips

Philips SCD 469 Bedienungsanleitung

Oricom

Oricom Babysense 7 Bedienungsanleitung

Levana

Levana TW502 Bedienungsanleitung

Luvion

Luvion Essential Bedienungsanleitung

Philips

Philips AVENT SCD841 Bedienungsanleitung

NUK

NUK Eco Control Video Display 550VD Bedienungsanleitung

Lorex

Lorex sweet peek mini Bedienungsanleitung

Mondevices

Mondevices MonBaby 2 Bedienungsanleitung

Famidoc

Famidoc FDBB-V2 Bedienungsanleitung

Graco

Graco iMonitor 2797 Bedienungsanleitung

babymoov

babymoov High Care A014001 Bedienungsanleitung

Ramili

Ramili RV1000 Bedienungsanleitung

Philips

Philips SBC SC364 Bedienungsanleitung

Swann

Swann SW231-FLO Bedienungsanleitung

Badabulle

Badabulle Baby Online 300 m+ Bedienungsanleitung

Philips AVENT

Philips AVENT SCD526/00 Bedienungsanleitung

Uniden

Uniden Guardian UBR223 Bedienungsanleitung

Summer

Summer Day & Night 28470A Bedienungsanleitung