Toro Precision Soil Sensor Bedienungsanleitung

Specifications

• Power Supply: 4.5 VDC supplied by three size-AA alkaline batteries

• Housing Material: High-impact, UV-resistant ABS

• Moisture Protection: Electronic circuitry encased in solid epoxy;

battery compartment sealed by O-ring

• Signal Quality Indicator: Tri-colored (Red, Yellow, Green) LED

• Stainless steel electrodes

• Built-in installation anchor stakes

• RF reception range: 500’ (152 m) LOS (line of sight)

• Operating Temperature: 14° F – 131° F (-10°C to +55°C)

Introduction

Congratulations on purchasing Toro’s new EVOLUTION®

controller with the Precision™ Soil Sensor add-on. With the

Precision™ Soil Sensor add-on, you will quickly realize savings

in both time and money while keeping your garden healthy

and beautiful.

EVOLUTION®Series Add-On:

Precision™Soil Sensor

EVOLUTION®Series Add-On:

Precision™Soil Sensor

LISTED

FCC-ID: OF753851

IC: 3575A-53851

Specications 1

Overview 3

Installation 4

EVOLUTION®Smart Connect®4

Precision™ Soil Sensor 4

Battery Installation 4

Sensor Setup 5

Add the Sensor to the Controller 5

Install and Calibrate the Sensor 6

Soil Sensor Menu 7

Navigating the Menu Interface 7

Getting to the Sensors Menu 7

Menu Settings 8

Moisture Now 8

Low reshold 8

Fine Tuning the Moisture Level 8

Signal Strength 9

Battery Level 9

Calibrate 9

Cal Setting 9

Current Temperature 10

Freeze O 10

ID 10

Review Screen 11

Appendix A: e Low reshold Setting 11

Appendix B: Site Selection and Earth Installation 12

FCC Statement 13

Toro Support 14

Table of Contents

e Precision™ Soil Sensor Add-On works with the EVOLUTION®Smart Connect®receiver.

It is possible to add up to three soil sensors per controller.

Overview

LED Signal

Indicator

(sold separately)

EVOLUTION®Smart Connect®

Precision™Soil Sensor

Battery Installation

e Soil Sensor works on three “AA” Alkaline or Lithium

batteries (not included).

1. Remove four Phillips screws securing the sensor

battery compartment cover (Figure 1). Set cover

aside.

2. Install the batteries (Figure 2).

3. Ensure the O-ring is in place then install the battery

compartment cover.

When batteries are initially installed, the LED

signal indicator is red. When the receiver links with

the sensor, the LED changes to green. e LED

will remain on for 30 minutes to facilitate sensor

installation.

1 2 3 4

Figure 2

Figure 1

Installation

Sensor Setup

Implement the following two procedures to successfully setup

Toro’s Precision™ Soil Sensor:

1. “Add” the sensor to the controller for successful wireless

communication.

2. Calibrate the sensor for proper irrigation operation.

1. Add the Sensor to the Controller

Every soil sensor has a unique

ID number. at number must

be “added” to the controller.

1. Press ADVANCED

then .

2. to ADD/REMOVE

DEVICE.

to conrm.

3. to SOIL 1. to ADD. to conrm.

4. e EVOLUTION®controller waits for the identication

signal from the soil sensor.

• If the soil sensor has had batteries installed in the last 30

minutes, the controller should detect and add the sensor

immediately.

• If the sensor is out in the eld, it could take up to a half

an hour to detect and add the sensor.

• One can remove and reinstall the soil sensor’s batteries to

achieve immediate sensor detection.

ZONE DETAILS

SCHEDULE STARTS

SCHEDULE DETAILS

SENSORS

ADVANCED

→

ADD/REMOVE DEVICE

→

WS ADD

SOIL 1 ADD

SOIL 2 ADD

SOIL 3 ADD

AUX 2 ADD

ADD/REMOVE DEVICE

→

ADD

INSTALL BATTERY OR

WAIT FOR SIGNAL

MAY TAKE 30 MINUTES

ADD/REMOVE DEVICE

CANCEL

5. e controller will detect the soil sensor. Conrm that the

sensor ID detected matches the sensor’s SN ID.

6. If it does match, press and continue to Calibrate the

Sensor.

If it does not match, change YES to NO, press , and

repeat steps 3-5.

2. Install and Calibrate the Sensor

e Precision™ Soil Sensor interprets soil moisture content on

a scale of 0% (extremely dry) to 100% (very wet). e key to

understanding how to calibrate a soil sensor is that the operator

must teach the 100% moisture level to the sensor.

1. After selecting YES from the previous screen, follow the

onscreen instructions below. Install the soil sensor in the

ground.

(See Appendix B: Site Selection and Earth Installation for

complete instructions on good sensor location.)

If soil sensor is not installed in the ground within that 30

minute “window”, the controller removes the sensor and

installation will have to be redone.

2. Return to the controller and conrm that the signal

strength (see above graphic) is good. If signal strength is

weak, relocate the sensor to a spot closer to the controller.

3. Press when satised.Use the and to adjust

the calibration setting (default 5: approximately a 1-day

“watch window”). Press .

e “Cal Setting” number adjusts the time it takes to

calibrate the sensor. A Cal Setting of ‘0’ calibrates the

sensor to the current moisture level in the ground. e

SOIL 1

DEVICE ID 05952

CORRECT?

ADD/REMOVE DEVICE

YES INSTALL SENSOR

IN GROUND

SIGNAL STRENGTH

ADD/REMOVE DEVICE

CONTINUE

calibration will be set using the next sensor reading

(within 30 minutes).

Additional calibration settings are available. From ‘1’ (~1

day “watch window”) to ‘168’ (~7 day “watch window”).

4. Move to the YES eld after CALIBRATE NOW?

Press . Sensor calibration begins.

5. Press to return to the Home screen. A message on the

bottom of the Home screen indicates that the sensor is

calibrating. e message clears when calibration is nished.

The Soil Sensor Menu

e EVOLUTION®controller’s Soil Sensor menu displays

sensor information as well as allows the user to modify certain

settings.

Navigating the Menu Interface

• Use or to navigate the menu commands.

• To change a value, press or to move to the desired

eld, then press and to adjust the value.

• Press to input the desired value.

Getting to the Sensors Menu

1. Press ADVANCED then .

2. Press to SENSORS. Press .

CAL SETTING 5

CALIBRATE NOW?

ADD/REMOVE DEVICE

YES

TUE

10/29

SCHEDULE A

NOT WATERING TODAY

HOME

SOIL 1 CALIBRATING

11:18AM

→

ZONE RUNTIMES

ZONE DETAILS

SCHEDULE STARTS

SCHEDULE DETAILS

ADVANCED

→

SENSORS

→

3. Press to select the desired soil sensor.

4. To add a sensor to a schedule:

Press or to select the desired Schedule (A, B, or C).

Press or to make the sensor active for the

selected schedule.

: Sensor is active.

-: Sensor is disabled.

In the screen above, a rain sensor is assigned to schedule B

and a soil sensor to schedule A.

5. Press until the Soil Sensor menu appears.

Menu Settings

MOISTURE NOW

is displays the current moisture level, as a percentage, of the

soil. 100% is the soil level set after the rst calibration

(see Calibrate the Sensor, page 6).

LOW THRESHOLD

is is the point at which the soil sensor will let the controller

resume irrigation of the landscape. If you were to compare the

soil to a gas tank, the “low threshold” would be the point at

which you rell the gas tank.

For a detailed explanation of the low threshold setting,

please read Appendix A of this manual.

SOIL 1

A B C

RAIN - -

WEATHER - - -

- -

SOIL 2 - - -

SENSORS

→

MOISTURE NOW 100%

LOW THRESHOLD 50%

SIGNAL STRENGTH

BATTERY LEVEL GOOD

CALIBRATE START

SOIL 1 SENSOR

→

LOW THRESHOLD

Fine-tuning the “Low reshold” Moisture Level

Changes to the 50% setting should be made initially in 5%

increments in order to see results within a few days. e

objective is to nd the moisture setting that results in a mild

stress condition in the lawn, indicated by slight wilting and

dryness. At that point, adjust the setting 5% in the opposite

direction. is should result in moisture maintenance level

that’s very close to optimum.

1. Press or to increase or decrease the Low

reshold point by 1%.

2. Press to input the desired value.

SIGNAL STRENGTH

Indicates signal strength as a series of bars ( ).

BATTERY LEVEL

Indicates the battery strength in the soil sensor.

CALIBRATE

Calibration is required to establish the maximum amount of

usable moisture in the soil. e sensor will then recognize this soil

moisture level as the maximum capacity (100%). From this xed

reference point, the sensor determines when the soil moisture has

dropped enough (to the “Low reshold”) to allow watering.

Manual calibration: At some point, it might be necessary to

recalibrate the sensor (in the event of a sensor relocation for

example).

1. Run an automatic or manual watering operation to

thoroughly irrigate the sensor zone.

2. Go to the Sensor Menu of the soil sensor to calibrate.

3. Press to CAL SETTING. Use to move

to the number eld. Use or to adjust the

calibration number (default 5: approximately a 1-day

“watch window”). Press to conrm.

e “Cal Setting” number adjusts the time it takes to

calibrate the sensor. A Cal Setting of ‘0’ calibrates the

sensor to the current moisture level in the ground. e

calibration will be set using the next sensor reading

(within 30 minutes).

Additional calibration settings are available. From ‘1’ (~1

day “watch window”) to ‘168’ (~7 day “watch window”).

LOW THRESHOLD 50%

SIGNAL STRENGTH

BATTERY LEVEL GOOD

CALIBRATE CANCEL

CAL SETTING

SOIL SENSOR

→

4. Press to CALIBRATE. to START.

to conrm.

5. START will turn to CANCEL.

Over the specied time period (see note above), the soil sensor

will “learn” the 100% mark and transmit that information

to the controller. At the end of the time period, soil sensor

calibration is done.

6. If you have not already directed the soil sensor to control a

schedule (page 8), please do so now.

FREEZE OFF AT

Freeze O is the temperature at which irrigation will be turned

o due to cold temperatures.

1. or raises or lowers the temperature value.

2. Press to input the value.

It is possible to disable the Freeze O feature.

Lowering the temperature past 29°F will show OFF.

Press the to input the value.

Displays the ID of the selected soil sensor.

CURRENT TEMP

Displays the temperature of the sensor at ground level (not at

“spike” level).

MOISTURE NOW 100%

LOW THRESHOLD 50%

SIGNAL STRENGTH

BATTERY LEVEL GOOD

CALIBRATE START

SOIL SENSOR

→

START

CALIBRATE

CAL SETTING 5

FREEZE OFF AT

ID 00 59 52

CURRENT TEMP 81°F

SOIL SENSOR

29°F

→

Andere Handbücher für Precision Soil Sensor

Inhaltsverzeichnis

Andere Toro Zubehör Handbücher

Toro

Toro 136-1199 Bedienungsanleitung

Toro

Toro Precision PSS-KIT Bedienungsanleitung

Toro

Toro EVOLUTION Series Bedienungsanleitung

Toro

Toro XTRA SMART Montageanleitung

Toro

Toro TEMPUS-AG-MS Bedienungsanleitung

Toro

Toro TWRS-I Bedienungsanleitung

Toro

Toro LoRa TEMPUS AIR PS Bedienungsanleitung

Toro

Toro Precision Bedienungsanleitung

Toro

Toro 02951 Bedienungsanleitung

Toro

Toro TEMPUS-AG-4G Bedienungsanleitung

Toro

Toro EVOLUTION Series Bedienungsanleitung

Toro

Toro WIRED RAINSENSOR 53769 Bedienungsanleitung

Toro

Toro OSMAC Satellite Bedienungsanleitung

Toro

Toro 115-8492 Bedienungsanleitung

Toro

Toro SIK Bedienungsanleitung

Toro

Toro Wireless RainSensor TWRS Betriebsanleitung

Toro

Toro 02945 Bedienungsanleitung

Toro

Toro OSMAC Bedienungsanleitung

Toro

Toro RainSensor + Freeze 53853 Bedienungsanleitung

Toro

Toro TEMPUS-AG-PR Bedienungsanleitung

Toro

Toro OSMAC Bedienungsanleitung

Toro

Toro myTurf 114-5144 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung