Toro 25531E Bedienungsanleitung
Operator’s Manual
Trencher Drive
Maxi Sneaker 370 Vibratory Plow
Model
25531E
25531T
3462-332A Original Instructions (EN) *3462-332*A
Chapter 1
Safety
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.
Trencher Safety Decal Locations
G434864
Decal 147-5641 Decal 147-5807
Decal Part: 147-5641
decal147-5641
Tie down
Safety Page 1–1 3462-332 A
Trencher Safety Decal Locations (continued)
Decal Part: 147-5654
decal147-5654
Attachment selector lever.
Decal Part: 147-5655
147-5655
Trencher chain direction selector
lever.
Decal Part: 147-5807
decal147-5807
Cutting/dismemberment hazard,
trencher—keep at least 2 m (6 ft) away.
3462-332A Page 1–2 Safety: Safety and Instructional Decals
Chapter 2
Installation
1Installing the Trencher Control Valve
Parts Required
1 Trencher control valve
2 90-degree connector
1 Straight connectors
1 45-degree connector
1 Large straight connector
1 Trencher handle
2 Nut (M10)
1 Knob
1 Trencher valve bracket
3 Bolt (M8)
3 Nut (M8)
IMPORTANT
Leave the nuts loose on connectors (1, 4, and 5) until the mating hose and hardlines
are installed.
G432647
1. Remove the 2 covers and the engine
hood from the right side of machine, set
these aside.
Installation Page 2–1 3462-332 A
G432648
2. Install the 5 connectors onto the trencher
control valve .
• 90-degree connector
• Straight connector
• Extended straight connector
• 90-degree connector
• 45-degree connector
G432649
3. Install the trencher handle onto the trencher
control valve using the 2 nuts (M10) ,
and the knob .
G432650
4. Loosely mount the trencher control valve
onto the bracket–trencher valve with 3 bolts
(M8) and 3 nuts (M8).
5. Use the hardware from the cover to mount the
trencher control valve and bracket to the
machine.
3462-332A Page 2–2 Installation: Installing the Trencher Control Valve
2Installing the Hoses
Installing Hoses With or Without the Hydra Borer
Parts Required
1 88-inch hose
1 Hose mount bracket
1 83-inch hose
1 26-1/2 inch hose
1 Hardline (5/8 inch)
2 Abrasion sleeve (1 X 24 inches)
1 Abrasion sleeve (2 X 60 inches)
1 90 degree connector
1. Connect the 88-inch hose to port T on the on the trencher control valve.
G432651
2. Connect the 83-inch hose to port P1 on the trencher control valve.
3. Place the 2 abrasion sleeves (1 X 24 inches) over the 83-inch hose and the 88-inch
hose, secure each end with zip ties.
4. Place the large abrasion sleeve (2 X 60 inches) over the 2 previous sleeves and secure
each end with zip ties.
5. Route the 88-inch and 83-inch hoses down and around the front of the machine.
Note: The hoses will be connected in a future step.
Installation: Installing the Hoses Page 2–3 3462-332 A
Installing Hoses With or Without the Hydra Borer
(continued)
6. Connect the 26-1/2 inch hose from the pump tandem to the 90 degree connector on
port P on the trencher control valve.
G432654
7. Connect the hardline, from this kit, to the existing hardline, on the machine, and inner
connector on trencher control valve in port T.
IMPORTANT
Ensure that the O-ring inserts into the hardline before connecting it to the hardline
routing under the coolant reservoir.
G434685
3462-332A Page 2–4 Installation: Installing the Hoses
Installing the Hoses Without the Hydra Borer
Parts Required
1 16-inch hose
1 45-degree connector
1 90-degree connector
1. Connect the 16-inch hose to the short end of the 90-degree connector.
2. Connect the long end of the 90-degree connector to the existing hose attached to the
plow control valve.
G432656
3. Connect the 16-inch hose to the 45-degree connector on the trencher control valve.
Installation: Installing the Hoses Page 2–5 3462-332 A
Installing Hoses With the Hydra Borer
Parts Required
1 Hardline
1. Connect the short hardline to the previously installed hardline and the 45-degree
connector, on the hydra borer valve, in port T.
IMPORTANT
Ensure that the O-ring inserts into the hardline before connecting it to the longer
hardline.
G434345
2. Connect the longer hardline, from the hydra borer kit, from the straight fitting in the P
port on the hydra borer valve to the 45-degree connector on the side of the trencher
valve.
G436604
Installation: Installing the Hoses Page 2–7 3462-332 A
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Toro Landwirtschaftliche Geräte Handbücher
Toro
Toro Infield Pro 5040 Bedienungsanleitung
Toro
Toro 08751 Bedienungsanleitung
Toro
Toro 23513 Bedienungsanleitung
Toro
Toro 22573 Bedienungsanleitung
Toro
Toro 03621 Bedienungsanleitung
Toro
Toro Reelmaster 7000-D Bedienungsanleitung
Toro
Toro 2226 Kurzanleitung
Toro
Toro 41245 Bedienungsanleitung
Toro
Toro Reelmaster 5510 Bedienungsanleitung
Toro
Toro ProLine 30139 Bedienungsanleitung
Toro
Toro Groundsmaster 5900 ROPS Bedienungsanleitung
Toro
Toro Multi Pro 5800 Bedienungsanleitung
Toro
Toro 133-6314 Bedienungsanleitung
Toro
Toro Groundsmaster 4500-D Bedienungsanleitung
Toro
Toro Workman 3000 Series Bedienungsanleitung
Toro
Toro Sand Pro 140-0274 Bedienungsanleitung
Toro
Toro Outcross 9060 Series Bedienungsanleitung
Toro
Toro 41614 Bedienungsanleitung
Toro
Toro Reelmaster 33455 Bedienungsanleitung
Toro
Toro Dingo TX 22306 Bedienungsanleitung
