Toro 30856 Handbuch

Printed in the USA

2003 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Groundsmaster4500-D

Groundsmaster Traction Unit

Model No. 30856—Serial No. 230000701 and Up

Form No. 3350–720

CE Compliance Set Up Instructions

Note: Determine the left and right sides of the machine from the normal operating position.

Loose Parts

Note: Use this chart as a checklist to ensure that all parts necessary for assembly have been received. Without these parts,

total setup cannot be completed. Some parts may have already been assembled at the factory.

Description Qty. Use

Throttle stop

Set screw 1

1Install for CE compliance

Lift latch

Latch bracket –R.H.

Latch bracket –L.H.

Flange lock nut 1/4–20

Install on control console for CE compliance

Lock bracket

Screw 1/4–20 x 1/2”

Washer .281 x .625

Lock nut 1/4–20

Install on hood latch for CE compliance

EEC decals 2Apply to machine for CE compliance.

EEC certificate 2

Install Throttle Stop

1. Loosen set screw on throttle stop.

2. Slide throttle stop onto high idle stop screw (Fig. 1).

Slot in throttle stop to be positioned over rib on engine.

3. Start engine and allow to run for 5 to 10 minutes. The

temperature gauge needle should be in the yellow

before proceeding to next step.

4. If cutting units are equipped with standard angled sail

blades, adjust high idle to 2575 rpm with the cutting

units disengaged. If equipped with high lift parallel sail

blades, adjust high idle to 2550 rpm with the cutting

units disengaged.

5. Tighten setscrew. Apply adhesive into setscrew to

prevent tampering.

Figure 1

1. Throttle stop 2. Set screw

Install Cutting Unit Lift Latch

1. Rotate latches and remove control panel cover (Fig. 2).

Figure 2

1. Operators control panel

2. Capscrews

3. L.H. latch bracket

4. R.H. latch bracket

5. Lift latch

2. Under front of control panel, locate ends of capscrews

securing control panel to frame (Fig. 2).

3. Insert left hand latch bracket up thru lift lever slot and

onto capscrew. Loosely secure with 1/4–20 flange nut

(Fig. 2).

4. Insert right hand latch bracket up thru lift lever slot and

onto capscrew. Loosely secure with 1/4–20 flange nut

(Fig. 2).

5. On top of control panel, insert each end tab of lift latch

into holes in latch brackets (Fig. 2). Tighten flange nuts.

Installing the Hood Latch

1. Unhook the hood latch from the hood latch bracket

(Fig. 3).

2. Slide the hood lock bracket onto the latch (Fig. 3).

3. Hook the latch onto the hood latch bracket (Fig. 3).

4. Insert a bolt (1/4 x 1-1/2 in.) through the hood lock

bracket and secure it with a flat washer and locknut

(Fig. 3).

Figure 3

1. Hood latch

2. Hood latch bracket 3. Hood lock bracket

Andere Handbücher für 30856

Andere Toro Rasenmäherzubehör Handbücher

Toro

Toro 136-9046 Bedienungsanleitung

Toro

Toro 03668 Bedienungsanleitung

Toro

Toro 117-9314 Bedienungsanleitung

Toro

Toro 04540 Bedienungsanleitung

Toro

Toro 79336 Bedienungsanleitung

Toro

Toro 110-6506 Bedienungsanleitung

Toro

Toro 30555 Bedienungsanleitung

Toro

Toro 140-9324 Bedienungsanleitung

Toro

Toro 132-6960 Bedienungsanleitung

Toro

Toro 131-2814 Bedienungsanleitung

Toro

Toro 78514 Bedienungsanleitung

Toro

Toro 110-2026 Bedienungsanleitung

Toro

Toro 23163 Bedienungsanleitung

Toro

Toro 145-3530 Bedienungsanleitung

Toro

Toro 31200 Bedienungsanleitung

Toro

Toro 106-2643 Bedienungsanleitung

Toro

Toro 30810 Bedienungsanleitung

Toro

Toro 136-1664 Bedienungsanleitung

Toro

Toro 120-7122 Bedienungsanleitung

Toro

Toro 30215 Bedienungsanleitung

Toro

Toro 79216 Bedienungsanleitung

Toro

Toro 04553 Bedienungsanleitung

Toro

Toro 110-2025 Bedienungsanleitung

Toro

Toro 140-5605 Bedienungsanleitung

Beliebte Rasenmäherzubehör Handbücher anderer Marken

Ariens

Ariens 891008 Bedienungsanleitung

Rover

Rover 108 - 109 Bedienungsanleitung

Snapper

Snapper 1690047 Bedienungsanleitung

Scag Power Equipment

Scag Power Equipment GC-F4 Bedienungsanleitung

RHINO

RHINO 800 Bedienungsanleitung

Exmark

Exmark Quest 126-7506 Bedienungsanleitung

Snapper

Snapper 1685167 Bedienungsanleitung

Cub Cadet

Cub Cadet 19B70029100 Bedienungsanleitung

Stihl

Stihl AMK 043.1 Bedienungsanleitung

MTD

MTD 753-0873 Handbuch

Bush Hog

Bush Hog RG60 Bedienungsanleitung

Land Pride

Land Pride RCF2760 Bedienungsanleitung

Simplicity

Simplicity 211 Bedienungsanleitung

Exmark

Exmark ULTRAVAC QUICK DUMP SYSTEM Bedienungsanleitung

Excel

Excel Two Bag Catcher Bedienungsanleitung

Textron

Textron Jacobsen Pro12 DFS Bedienungsanleitung

Ryobi

Ryobi AC018130 Bedienungsanleitung

Snapper

Snapper 4544 Einrichtungshandbuch