Toro Groundsmaster 4000-D Bedienungsanleitung

(Model 30410)

PART NO. 02097SL (Rev. F)

Service Manual

GroundsmasterR4000--D

Preface

The purpose of this publication is to provide the service

technician with information for troubleshooting, testing,

and repair of major systems and components on the

Groundsmaster 4000--D.

REFER TO THE TRACTION UNIT AND CUTTING

UNIT OPERATOR’S MANUALS FOR OPERATING,

MAINTENANCE, AND ADJUSTMENT INSTRUC-

TIONS. Space is provided in Chapter 2 of this book to

insert the Operator’s Manuals and Parts Catalogs for

your machine. Replacement Operator’s Manuals and

Parts Catalogs are available on the internet at www.To-

ro.com.

TheToroCompanyreservestherighttochangeproduct

specifications or this publication without notice.

This safety symbol means DANGER, WARNING,

or CAUTION, PERSONAL SAFETY INSTRUC-

TION. When you see this symbol, carefully read

the instructions that follow. Failure to obey the

instructions may result in personal injury.

NOTE: ANOTE will give general information about the

correct operation, maintenance, service, testing, or re-

pair of the machine.

IMPORTANT: The IMPORTANT notice will give im-

portant instructionswhichmustbefollowedtopre-

vent damage to systems or components on the

machine.

EThe Toro Company -- 2002, 2003, 2004, 2006, 2007, 2012

Groundsmaster 4000−D

This page is intentionally blank.

Rev. E

Groundsmaster 4000−D

Table Of Contents

Chapter 1 − Safety

General Safety Instructions 1 − 2. . . . . . . . . . . . . . . . . .

Jacking Instructions 1 − 4. . . . . . . . . . . . . . . . . . . . . . . . .

Safety and Instruction Decals 1 − 5. . . . . . . . . . . . . . . .

Chapter 2 − Product Records and Maintenance

Product Records 2 − 1. . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance 2 − 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Equivalents and Conversions 2 − 2. . . . . . . . . . . . . . . .

Torque Specifications 2 − 3. . . . . . . . . . . . . . . . . . . . . . .

Chapter 3 − Kubota Diesel Engine

General Information 3 − 2. . . . . . . . . . . . . . . . . . . . . . . .

Specifications 3 − 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Adjustments 3 − 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service and Repairs 3 − 6. . . . . . . . . . . . . . . . . . . . . . . .

KUBOTA WORKSHOP MANUAL, DIESEL ENGINE,

V2003−T SERIES

Chapter 4 − Hydraulic System

Specifications 4 − 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

General Information 4 − 3. . . . . . . . . . . . . . . . . . . . . . . .

Hydraulic Schematic 4 − 6. . . . . . . . . . . . . . . . . . . . . . . .

Hydraulic Flow Diagrams 4 − 8. . . . . . . . . . . . . . . . . . . .

Special Tools 4 − 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting 4 − 20. . . . . . . . . . . . . . . . . . . . . . . . . . .

Testing 4 − 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Adjustments 4 − 48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service and Repairs 4 − 49. . . . . . . . . . . . . . . . . . . . . . .

Chapter 5 − Electrical System

Electrical Schematic, Circuit Diagrams, and

Wire Harness Drawings 5 − 2. . . . . . . . . . . . . . . . . . . .

Special Tools 5 − 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting 5 − 4. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electrical System Quick Checks 5 − 7. . . . . . . . . . . . . .

Component Testing 5 − 8. . . . . . . . . . . . . . . . . . . . . . . . .

Service and Repairs 5 − 28. . . . . . . . . . . . . . . . . . . . . . .

Chapter 6 − Axles, Planetaries, and Brakes

Specifications 6 − 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Adjustments 6 − 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service and Repairs 6 − 4. . . . . . . . . . . . . . . . . . . . . . . .

Chapter 7 − Chassis

Service and Repairs 7 − 2. . . . . . . . . . . . . . . . . . . . . . . .

Chapter 8 − Cutting Units

Specifications 8 − 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting 8 − 3. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Adjustments 8 − 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service and Repairs 8 − 6. . . . . . . . . . . . . . . . . . . . . . . .

Chapter 9 − Electrical Diagrams

Electrical Schematic 9 − 3. . . . . . . . . . . . . . . . . . . . . . . .

Circuit Diagrams 9 − 5. . . . . . . . . . . . . . . . . . . . . . . . . . .

Wire Harness Drawings 9 − 9. . . . . . . . . . . . . . . . . . . . .

SafetyProduct Records

and Maintenance

Kubota

Diesel Engine

Hydraulic

System

Electrical

System

Axles, Planetaries,

and Brakes

Cutting Units Chassis

Electrical

Diagrams

Groundsmaster 4000−D

This page is intentionally blank.

Groundsmaster 4000−D Page 1 − 1 Safety

Chapter 1

Safety

Table of Contents

GENERAL SAFETY INSTRUCTIONS 2. . . . . . . . . . . .

Before Operating 2. . . . . . . . . . . . . . . . . . . . . . . . . . . .

While Operating 2. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance and Service 3. . . . . . . . . . . . . . . . . . . .

JACKING INSTRUCTIONS 4. . . . . . . . . . . . . . . . . . . . .

SAFETY AND INSTRUCTION DECALS 5. . . . . . . . . .

Safety

Groundsmaster 4000−D

Page 1 − 2

Safety

General Safety Instructions

The GROUNDSMASTER 4000-D was tested and certi-

fied byTORO for compliance with the B71.4-1999 speci-

fications of the American National Standards Institute.

Although hazard control and accident prevention par-

tially are dependent upon the design and configuration

of the machine, these factors are also dependent upon

the awareness, concern, and proper training of the per-

sonnel involved in the operation, transport, mainte-

nance, and storage of the machine. Improper use or

maintenance of the machine can result in injury or

death. To reduce the potential for injury or death, comply

with the following safety instructions.

WARNING

To reduce the potential for injury or death,

comply with the following safety instructions.

Before Operating

1. Read and understand the contents of the Operator’s

Manual before starting and operating the machine. Be-

come familiar with the controls and know how to stop the

machine and engine quickly. A replacement Operator’s

Manual is available on the Internet at www.Toro.com or

by sending the complete model and serial number to:

The Toro Company

Attn. Technical Publications

8111 Lyndale Avenue South

Bloomington, Minnesota 55420−1196

2. Keep all shields, safety devices, and decals in place.

If a shield, safety device, or decal is defective, illegible

or damaged, repair or replace it before operating the

machine. Also tighten any loose nuts, bolts or screws to

ensure machine is in safe operating condition.

3. Assure interlock switches are adjusted correctly so

engine cannot be started unless traction pedal is in

NEUTRAL and cutting units are DISENGAGED.

4. Since diesel fuel is highly flammable, handle it care-

fully:

A. Use an approved fuel container.

B. Do not remove fuel tank cap while engine is hot or

running.

C. Do not smoke while handling fuel.

D. Fill fuel tank outdoors and only to within an inch of

the top of the tank, not the filler neck. Do not overfill.

E. Wipe up any spilled fuel.

While Operating

1. Sit on the seat when starting and operating the ma-

chine.

2. Before starting the engine:

A. Engage the parking brake.

B. Make sure traction pedal is in neutral and the

PTO switch is OFF (disengaged).

C. After engine is started, release parking brake and

keep foot off traction pedal. Machine must not move.

If movement is evident, the traction pedal linkage is

adjusted incorrectly; therefore, shut engine off and

adjust until machine does not move when traction

pedal is released.

3. Do not run engine in a confined area without ade-

quate ventilation. Exhaust fumes are hazardous and

could possibly be deadly.

4. Do not touch engine, muffler or exhaust pipe while

engine is running or soon after it is stopped. These areas

could be hot enough to cause burns.

5. Before getting off the seat:

A. Ensure that traction pedal is in neutral.

B. Set parking brake.

C. Disengage cutting units and wait for blades to

stop.

D. Stop engine and remove key from switch.

E. Toro recommends that anytime the machine is

parked (short or long term), the cutting units should

be lowered to the ground. This relieves pressure

from the lift circuit and eliminates the risk of cutting

units accidentally lowering to the ground.

F. Do not park on slopes unless wheels are chocked

or blocked.

Groundsmaster 4000−D Page 1 − 3 Safety

Maintenance and Service

1. Before servicing or making adjustments, lower

decks, stop engine, set parking brake, and remove key

from the switch.

2. Make sure machine is in safe operating condition by

keeping all nuts, bolts and screws tight.

3. Never store the machine or fuel container inside

where there is an open flame, such as near a water heat-

er or furnace.

4. Make sure all hydraulic line connectors are tight, and

all hydraulic hoses and lines are in good condition be-

fore applying pressure to the system.

5. Keep body and hands away from pin hole leaks in hy-

draulic lines that eject high pressure hydraulic fluid. Use

cardboard or paper to find hydraulic leaks. Hydraulic

fluid escaping under pressure can penetrate skin and

cause injury. Fluid accidentally injected into the skin

must be surgically removed within a few hours by a doc-

tor familiar with this form of injury or gangrene may re-

sult.

6. Before disconnecting or performing any work on the

hydraulic system, all pressure in system must be re-

lieved by stopping engine and lowering cutting units to

the ground.

7. If major repairs are ever needed or assistance is de-

sired, contact an Authorized Toro Distributor.

8. To reduce potential fire hazard, keep engine area

free of excessive grease, grass, leaves and dirt. Clean

protective screen on machine frequently.

9. If engine must be running to perform maintenance or

an adjustment, keep hands, feet, clothing and other

parts of the body away from cutting units and other mov-

ing parts. Keep bystanders away.

10.Do not overspeed the engine by changing governor

setting. To assure safety and accuracy, check maximum

engine speed.

11.Shut engine off before checking or adding oil to the

crankcase.

12.Disconnect battery before servicing the machine.

Disconnect negative cable first and positive cable last.

If battery voltage is required for troubleshooting or test

procedures, temporarily connect the battery. Reconnect

positive cable first and negative cable last.

13.Battery acid is poisonous and can cause burns.

Avoid contact with skin, eyes, and clothing. Protect your

face, eyes, and clothing when working with a battery.

14.Battery gases can explode. Keep cigarettes, sparks,

and flames away from the battery.

15.At the time of manufacture, the machine conformed

to the safety standards for riding mowers. To assure op-

timum performance and continued safety certification of

the machine, use genuine Toro replacement parts and

accessories. Replacement parts and accessories made

by other manufacturers may result in non-conformance

with the safety standards, and the warranty may be

voided.

16.When changing attachments, tires, or performing

other service, use correct blocks, hoists, and jacks.

Make sure machine is parked on a solid level surface

such as a concrete floor. Prior to raising the machine, re-

move any attachments that may interfere with the safe

and proper raising of the machine. Always chock or

block wheels. Use jack stands or solid wood blocks to

support the raised machine. If the machine is not proper-

ly supported by blocks or jack stands, the machine may

move or fall, which may result in personal injury (see

Jacking Instructions).

Safety

Groundsmaster 4000−D

Page 1 − 4

Safety

Jacking Instructions

CAUTION

When changing attachments, tires, or perform-

ing other service, use correct blocks, hoists,

and jacks. Make sure machine is parked on a

solid level surface such as a concrete floor.

Prior to raising machine, remove any attach-

ments that may interfere with the safe and prop-

er raising of the machine. Always chock or block

wheels. Use jack stands or solid wood blocks to

support the raised machine. If the machine is

not properly supported by blocks or jack

stands, the machine may move or fall, which

may result in personal injury.

Jacking the Front End (Fig. 1)

1. Set parking brake and chock both rear tires to pre-

vent the machine from moving.

2. Position jack securely under the frame, just to the in-

side of the front tire.

3. Position jack stands or hardwood blocks under the

frame as close to the wheels as possible to support the

machine.

Jacking the Rear End (Fig. 2)

1. Place jack securely under the center of rear axle.

2. Chock both front tires. Jack rear of machine off the

ground.

3. Use jack stands or blocks under the axle to support

the machine.

1. Frame jacking point 2. Front tire

Figure 1

1. Rear axle jacking point 2. Rear tire

Figure 2

Groundsmaster 4000−D Page 1 − 5 Safety

Safety and Instruction Decals

Numerous safety and instruction decals are affixed to the Groundsmaster 4000−D. If any decal becomes illegible or

damaged, install a new decal. Part numbers are listed in your Parts Catalog.

Safety

Groundsmaster 4000−D

Page 1 − 6

Safety

This page is intentionally blank.

Andere Handbücher für Groundsmaster 4000-D

Inhaltsverzeichnis

Andere Toro Rasenmäher Handbücher

Toro

Toro Recycler 22187TE Bedienungsanleitung

Toro

Toro GrandStand 74534 Bedienungsanleitung

Toro

Toro TimeCutter ZX Handbuch

Toro

Toro 44409 Bedienungsanleitung

Toro

Toro Groundsmaster 4000-D Bedienungsanleitung

Toro

Toro 30864A Bedienungsanleitung

Toro

Toro Recycler 20357 Bedienungsanleitung

Toro

Toro 3660 Bedienungsanleitung

Toro

Toro Reccycler Bedienungsanleitung

Toro

Toro 72542TE Bedienungsanleitung

Toro

Toro TimeCutter 6000 Bedienungsanleitung

Toro

Toro TimeCutter MX 4275T Bedienungsanleitung

Toro

Toro HoverPro 450 Bedienungsanleitung

Toro

Toro 30230 Groundsmaster 225 Bedienungsanleitung

Toro

Toro 74571 M74571 Bedienungsanleitung

Toro

Toro F60 Bedienungsanleitung

Toro

Toro GrandStand Bedienungsanleitung

Toro

Toro TimeMaster 21219 Bedienungsanleitung

Toro

Toro 74741 Bedienungsanleitung

Toro

Toro Super Recycler 20792 Bedienungsanleitung

Toro

Toro 3706 Bedienungsanleitung

Toro

Toro ProLine 22038 Bedienungsanleitung

Toro

Toro TimeCutter 138-2537 Bedienungsanleitung

Toro

Toro 74408 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 050 thru 062 Bedienungsanleitung