Toro TimeCutter ZD Series Handbuch

Form No. 3357-921 Rev A

TimeCutter® ZD Riding Mower

Model No. All Models

Setup Instructions

Loose PartsUse the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

No parts required

–

Charge the battery.

Retainer clip

Screw, self-tapping (10 x 1/2 inch)

Install the bag clips.

Collection bag

DFS lever

Washer

Cotter pin

Install the collection bag.

Ignition Key

Operator’s Manual

Engine Operator’s Manual

Complete the Setup.

Note: Deter mine the left and right sides of the mac hine from the nor mal operating position.

Step

Charging the Battery

No Parts Required

Procedure

Bulk electrolyte with 1.260 speciﬁc g ra vity m ust be

purc hased from a local batter y supply outlet.

Batter y electr ol yte contains sulfuric acid

which is a deadl y poison and causes sev er e

bur ns.

• Do not drink electr ol yte and a v oid

contact with skin, ey es or clothing . W ear

safety g lasses to shield y our ey es and

r ob ber g lo v es to pr otect y our hands.

• Fill the batter y wher e clean w ater is

al w ays a v aila ble f or ﬂushing the skin.

• F ollo w all instr uctions and compl y with

all safety messa ges on the electr ol yte

container .

1. Raise the seat to access the batter y .

2. R emo v e the batter y from the mac hine and

place it on a lev el surface; refer to the Operator’ s

Manual , R emo ving the Batter y .

Important: Nev er ﬁll the batter y with

electr ol yte while the batter y is installed in

the tractor . Electr ol yte could be spilled on

other par ts and cause cor r osion.

3. Clean the top of the batter y with a paper to w el.

4. R emo v e the v ent caps from the batter y

( Figure 1 ). Slo wly pour electrolyte into eac h

batter y cell until the electrolyte lev el is up to

the Upper line on the batter y case ( Figure 1 ).

Important: Do not o v erﬁll the batter y

because electr ol yte (sulfuric acid) can

cause sev er e cor r osion and dama ge to the

chassis.

Figure 1

1. Vent caps

3. Lower line2. Upper line

5. W ait ﬁv e to ten min utes after ﬁlling the

batter y cells . Add electrolyte , if necessar y , until

the electrolyte lev el is up to the Upper line

( Figure 1 ) on the batter y case .

6. Install the batter y v ent caps .

7. Connect the c harg er leads to the cor responding

batter y posts as sho wn in Figure 2 .

Figure 2

1. Positive Battery Post

3. Red (+) Charger Lead2. Negative Battery Post

4. Black (-) Charger Lead

Charging the batter y pr oduces gasses

that can explode.

Nev er smok e near the batter y and k eep

spar ks and ﬂames a w ay fr om batter y .

8. Charg e the batter y for 10 to 15 min utes at

25 to 30 amps or 30 min utes at 4 to 6 amps

( Figure 2 ). Do not o v erc harg e the batter y .

9. W hen ﬁnished, unplug the c harg er from the

electrical outlet, then disconnect the c harg er

leads from the batter y posts ( Figure 2 ).

Note: Do not r un the mac hine with the

batter y disconnected, electrical damag e ma y

occur .

10. Install the batter y to the mac hine; refer to the

Operator’ s Manual , Installing the Batter y .

11. Connect the positi v e batter y cable to the

positi v e batter y post using the existing

fasteners .

12. Connect the neg ati v e batter y cable to the

neg ati v e batter y post using the existing

fasteners .

Step

Installing the Bag Clips

Parts needed for this step:

Retainer clip

Screw, self-tapping (10 x 1/2 inch)

Procedure

1. Locate the bag clips and self taping screws in

loose par ts .

2. Install a bag clip to eac h side of the heat shield

as sho wn in Figure 3 . Install the clips to the

bac kside of the heat shield at the holes so the

contour of the clips matc h the contour of the

shield.

G005848

Figure 3

1. Bag clip 4. Holes, existing2. Screw

5. Heat shield3. Heat shield, backside 6. Bag clip, installed

3. R e peat this procedure for the remaining clip

on the opposing side of the heat shield.

Step

Installing the Collection Bag

Parts needed for this step:

Collection bag

DFS lever

Washer

Cotter pin

Procedure

1. R emo v e the DFS lev er and collection bag from

the pac kaging .

2. Install the DFS lev er into the opening on the

top of the collection bag Figure 4 .

G005849

Figure 4

1. DFS lever 3. Washer2. Collection bag

4. Cotter pin

3. Install a w asher o v er the end of the DFS lev er

inside the collection bag ( Figure 4 ).

4. Secure the lev er assembly with a cotter pin and

bend the ends to hold it place ( Figure 4 ).

5. Install the collection bag to the mac hine

( Figure 5 ). Install the lev er side pin in the

collection bag into the retaining hole in the

notc h of the engine co v er . Seat the opposing

pin into the other notc h in the engine co v er

and allo w the collection bag swing do wn into

place .

Figure 5

1. Collection bag 3. Retaining hole2. Engine cover

4. Pin, lever side

Step

Completing the Setup

Parts needed for this step:

Ignition Key

Operator’s Manual

Engine Operator’s Manual

Procedure

Checking the Tir e Pr essur e

Chec k the front and rear tires for proper inﬂation.

R efer to Chec king the Tire Pressure in the Operator’ s

Manual for the recommended inﬂation pressure .

Checking the Mo w er Adjustment

T he mo w er dec k w as lev eled at the factor y . If the

mo w er is not cutting lev el, adjust the side-to-side

lev el and the front-to-rear blade slope . See the

Operator’ s Man ual for the proper procedure .

Checking the Engine Oil Lev el

Before y ou star t the engine and use the mac hine ,

c hec k the oil lev el in the engine crankcase; refer to

Chec king the Oil Lev el in the Operator’ s Manual .

R eview the R emaining P ar ts

K ee p all the follo wing items with the mac hine:

•Ignition K ey

•Operator’ s Manual

•Engine Operator’ s Manual

Andere Toro Rasenmäher Handbücher

Toro

Toro Z500 Series Z Master Handbuch

Toro

Toro 30433 Bedienungsanleitung

Toro

Toro 71205 Wheel Horse 13-38 XLE Bedienungsanleitung

Toro

Toro Groundsmaster 4500-D Bedienungsanleitung

Toro

Toro 03698 Bedienungsanleitung

Toro

Toro 74642 Bedienungsanleitung

Toro

Toro 21136 Bedienungsanleitung

Toro

Toro TimeCutter MX 4200 Handbuch

Toro

Toro ProLine H800 Bedienungsanleitung

Toro

Toro 04130 Greensmaster 500 Bedienungsanleitung

Toro

Toro 20014 Bedienungsanleitung

Toro

Toro timecutter 19-52ZX Bedienungsanleitung

Toro

Toro 78261 Bedienungsanleitung

Toro

Toro 21852 Bedienungsanleitung

Toro

Toro Flex Force Power System 20361 Bedienungsanleitung

Toro

Toro TurfMaster 22205TE Bedienungsanleitung

Toro

Toro 170-DH Bedienungsanleitung

Toro

Toro 74585 Bedienungsanleitung

Toro

Toro Super Recycler 20092C Bedienungsanleitung

Toro

Toro 29639 Bedienungsanleitung

Toro

Toro 30881 Bedienungsanleitung

Toro

Toro 75746 Bedienungsanleitung

Toro

Toro 30318 Bedienungsanleitung

Toro

Toro 74840 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

Craftsman

Craftsman 917.378461 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung