Toshiba B-8204-QM-R Bedienungsanleitung

- 1 -

Rotary Cutter Module

B-8204-QM-R Installation Manual

1. APPLICABLE MODEL

This optional kit is the rotary cutter module, which is intended for the following models:

B-SX4T Series, B-SX5T Series

NOTE: When using the Rotary Cutter to the B-SX4T Series, be sure to install the Ribbon Saving Module

(B-9904-R/R2-QM). Failure to do this may cause a paper jam or ribbon error.

2. PACKING LIST

All the following parts are supplied with the kit. Make sure you have all items shown below.

Cutter Unit (1 pc.)

Cutter Cover (1 pc.) Cutter Drive Unit (1 pc.) Harness Ass’y

(2-pin & 9-pin) (1 pc.)

Cord Bush (1 pc.)

(For B-SX4 only)

Print Head Cleaner (1 pc.)

(P/No.: FMQB0051601)

• Installation Manual (1 copy)

• SM-4x8 Screw (6 pcs.)

3. INSTALLATION PROCEDURE

3.1 Installing the Rotary Cutter Unit on the B-SX4T Series

1) Turn the power off and disconnect the power cord.

2) Remove the two black screws to detach the front plate.

NOTE: Retain the two black screws and front plate.

WARNING

1. Follow all manual instructions. Failure to do so could create safety hazards such as fire or

electrocution.

• Manual instructions must be followed when installing option kits or adding cables to avoid

system failures and to insure proper performance and operation

• Failure to follow manual instructions or any unauthorized modifications, substitution or change

to this product will void the limited product warranty.

2. Turn the power off and disconnect the power cord before installing the rotary cutter module.

3. Be careful not to injure your fingers when installing the swing cutter module.

4. Be careful not to pinch your fingers or hands with the covers.

Front Plate

Black Screws

Get other manuals https://www.bkmanuals.com

- 2 -

3) Remove the four B-4x5 screws from the side panel (L).

4) Open the top cover and remove the three P-4x8 screws that secure the side panel (L).

5) Lift the side panel (L) and put it aside.

6) Disconnect the fan motor harness from CN19 on the Main PC board, and then separate the side

panel (L).

7) Fix the cutter drive unit to the printer with the three SM-4x8 screws.

B-4x5 Screw P-4x8 Screw

Top Cover

B-4x5 Screw

Side Panel (L)

SM-4x8 Screw

Cutter Drive Unit

Side Panel (L) Fan Motor Harness

Fan Motor

CN19

Main PC Board

SM-4x8 Screw

Get other manuals https://www.bkmanuals.com

- 3 -

8) Connect the 9-pin connector of the harness ass’y to CN7 and 2-pin connector to CN9 on the cutter

driver unit, respectively.

9) Fit the bush to the harness ass’y in the orientation as shown below.

10) Insert the harness ass’y into the hole in the main frame. Fit the bush into the hole.

CN7 (9 pins)

CN9 (2 pins)

Harness Ass’y

Bush

Harness Ass’y

Hole

Main Frame

Harness Ass’y

Get other manuals https://www.bkmanuals.com

- 4 -

11) Fix the harness ass’y with the clamp.

12) Connect the 9-pin connector of the harness ass’y to CN15, and 2-pin connector to CN18 on the

Main PC board, respectively.

13) Turn the head lever counterclockwise to Free position.

14) Open the ribbon shaft holder plate.

15) Raise the print head block until it stops.

Main PC Board

Clamp

Ribbon Shaft Holder Plate

Print Head Block

CN18 (2 pins)

CN15 (9 pins)

Harness Ass’y

Head Leve

Free position

Lock position

(Label)

Lock position

(Tag)

Stoppe

Get other manuals https://www.bkmanuals.com

- 5 -

16) Connect the four harnesses of the cutter unit to CN8, CN10, CN11 and CN12 on the cutter drive

unit.

17) Fit the two tabs of the cutter drive unit into the notches, and then fix the cutter unit with the three

SM-4x8 screws.

Cutter Unit

Cutter Drive Unit

Print Head Block

Cutter Unit

CN8 CN12 CN10

CN11

SM-4 x 8 Screw

Notch

Tab

Notch Tab

SM-4 x 8 Screw

Get other manuals https://www.bkmanuals.com

- 6 -

18) Attach the cutter cover to the cutter unit with the two screws so that the tab of the cutter cover turns

on the cutter cover open switch.

NOTES: 1. Be careful not to pinch the cutter harness by the cutter cover.

2. Make sure that the anti-static brush is protruding from the media outlet.

19) Close the print head block and ribbon shaft holder plate.

NOTE: DO NOT excessively push down the print head block to close it. Doing so may cause a

failure of the print head block or damage to the print head.

20) Reassemble the side panel (L) and close the top cover. Finally check the cutter operation.

Screw

Cutter Cover

Anti-static

Brush

Media Outlet

Cutter Cover

Open Switch

Tab

Cutter Cover

Get other manuals https://www.bkmanuals.com

- 7 -

3.2 Installing the Rotary Cutter Unit on the B-SX5T Series

Since the strip module is standard on the B-SX5T series, it is necessary to remove the rewinder guide plate,

strip sensor, etc. before installing the cutter module.

1) Turn the power off and disconnect the power cord.

2) When the printer is used in the batch or strip mode:

Remove the two black screws to detach the front plate.

NOTE: Retain the two black screws and front plate.

When the printer is used in the built-in rewinder mode:

Open the top cover, remove the two SMW-4x8 screws, and detach the rewinder guide plate from the

printer.

3) Remove the four B-4x5 screws from the side panel (L).

4) Open the top cover and remove the three P-4x8 screws that secure the side panel (L).

Front Plate

Black Screws

B-4x5 Screw P-4x8 Screw

Top Cover

B-4x5 Screw

Side Panel (L)

Rewinder Guide Plate

SMW-4x8B Screw

Get other manuals https://www.bkmanuals.com

- 8 -

5) Lift the side panel (L) and put it aside.

6) Disconnect the fan motor harness from CN19 on the Main PC board, and then separate the side panel

(L).

7) Remove the SM-4x8 screw that secures the operation panel ass’y.

8) Half open the top cover, otherwise the operation panel ass’y cannot be removed from the printer.

9) Lift the operation panel ass’y to release the hook, and then remove the operation panel ass’y by

moving it forward.

Operation Panel Ass’

Top Cover

SM-4x8 Screw

Side Panel (L) Fan Motor Harness

Fan Motor

CN19

Main PC Board

Get other manuals https://www.bkmanuals.com

- 9 -

10) Disconnect the operation panel harness from the operation panel ass’y.

11) Turn the head lever clockwise to Free position.

12) Open the ribbon shaft holder plate.

Operation Panel Ass’y

Ribbon Shaft Holder Plate

Operation Panel Harness

Hook

Head Leve

Free position

Lock position

(Label)

Lock position

(Tag)

Get other manuals https://www.bkmanuals.com

- 10 -

13) Raise the print head block until it stops.

14) Remove the two SMW-4x8 screws that secure the strip sensors (TR) and (LED).

15) Release the strip sensor (LED) harness from the cable clamp, and disconnect it from the shorter harness

of the strip sensor harness (TR).

Print Head Block

Stoppe

SMW-4x8B Screw

Strip Sensor (Tr)

SMW-4x8B Screw

Strip Sensor (LED)

Cable Clamp

Strip Sensor Harness

(for LED)

Shorter Harness of the Strip

Sensor Harness (for Tr)

Get other manuals https://www.bkmanuals.com

Andere Toshiba Steuereinheit Handbücher

Toshiba

Toshiba RBM-SV1121HUPE Bedienungsanleitung

Toshiba

Toshiba TCB-PCIN2E Bedienungsanleitung

Toshiba

Toshiba IK-TF7U Bedienungsanleitung

Toshiba

Toshiba PA912 Bedienungsanleitung

Toshiba

Toshiba GN2020 Bedienungsanleitung

Toshiba

Toshiba IK-HR1CD Bedienungsanleitung

Toshiba

Toshiba RBM-A101VAE Bedienungsanleitung

Toshiba

Toshiba TC Series Bedienungsanleitung

Toshiba

Toshiba BMS-SM1280HTLE Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-AS1 Series Bedienungsanleitung

Toshiba

Toshiba IK-HD2E Bedienungsanleitung

Toshiba

Toshiba e-STUDIO 810 Bedienungsanleitung

Toshiba

Toshiba LTD121EA43G Bedienungsanleitung

Toshiba

Toshiba B-EX700-WLAN2-QM-R Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-MB1 Bedienungsanleitung

Toshiba

Toshiba IK-HR1CS Bedienungsanleitung

Toshiba

Toshiba IK-CU44A Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-A7 Bedienungsanleitung

Toshiba

Toshiba BMS-SM1280HTLE Bedienungsanleitung

Toshiba

Toshiba 3 axis TB6560 Bedienungsanleitung

Toshiba

Toshiba B-EP700-BLTH-QM-R Bedienungsanleitung

Toshiba

Toshiba LONWORKS LIU007Z Bedienungsanleitung

Toshiba

Toshiba IK-HD1E Bedienungsanleitung

Toshiba

Toshiba nv Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung