Toshiba B-EP700-BLTH-QM-R Bedienungsanleitung

EO2-38061

1/8

TOSHIBA Bluetooth Module

B-EP700-BLTH-QM-R Installation Manual

Thank you for purchasing TOSHIBA Bluetooth module, B-EP700-BLTH-QM-R.

The B-EP700-BLTH-QM-R is an optional Bluetooth module for the B-EP2DL/EP4DL Series.

The pictures used in this document are those of the B-EP4DL, but the installation procedure is common with the

B-EP2DL unless otherwise noted.

1. PACKING LIST

The following parts are supplied with the kit. Make sure you have all items shown below.

Bluetooth Module (1 pc.)

Installation Manual (1 copy)

Standard Label (1 pc.)

FPC Cable

1. Follow all manual instructions. Failure to do so could create safety hazards such as fire or electrocution.

• Manual instructions must be followed when installing option kits or adding cables to avoid system

failures and to insure proper performance and operation.

• Failure to follow manual instructions or any unauthorized modifications, substitution or change to this

product will void the limited product warranty.

2. Turn the power off and remove the battery before installing the Bluetooth module.

3. Be careful not to pinch your fingers or hands with the covers.

WARNING!

For B-EP2DL Series (1pc.)

Connected to

Bluetooth module

Connected to

Main PCB

For B-EP4DL Series (1pc.)

Connected to

Bluetooth module

Connected to

Main PCB

2/8

2. INSTALLATION PROCEDURE

Step 1. Turn off the printer.

Step 2. Slide the battery lever in the direction of the arrow, and remove the battery pack from the printer.

Step 3. Remove the four tapping screws from the bottom cover.

Step 4. Press the top cover open button to open the top cover.

Step 5. Remove the left side cover in the direction of the arrow.

NOTE: The gears shown in the picture below is not secured and is easily removed. Be careful not to drop

and break or lose it.

B-EP4DL Series B-EP2DL Series

Gea

Top Cover

Top Cover Open Button Left Side Cover

Gea

Gear

T-3x10 Tapping Screw

Battery Pack

Battery

Lever

3/8

Step 6. Remove the right side cover and the front cover in the direction of the arrow, respectively.

Step 7. Connect the FPC cable to the Bluetooth module in the correct orientation.

Two FPC cables are supplied with the Bluetooth module. One is designed for the B-EP2DL series, and

the other is for the B-EP4DL series. Care must be taken not to mistake them for each other.

NOTE: Pass the FPC cable through the slot, as shown in the picture below. (B-EP4DL series only)

Step8. Connect the FPC cable to the CN301 connector on the Main PC board in the correct orientation.

Main PC Board

CN301

FPC Cable

Bluetooth

Module

FPC Cable

Slot

Right Side Cover

Front Cove

4/8

Step9. Fit the Bluetooth module into the following position.

Pass the FPC cable as shown below so that they do not get caught on the gears or by the cover.

Step10. Close the front cover.

NOTES: 1. Make sure that the pins on the both sides of the front cover are fit in position, as shown in the pictures

below.

2. Do not install the front cover with the top cover open button depressed. Doing so could disable the top

cover open button after the assembly, and as a result, the top cover cannot be opened.

Front Cover

B-EP4DL

FPC Cable

Cover O

en Button

Good No Good

B-EP2DL

FPC Cable

Bluetooth Module

5/8

Step11. Mount the left side cover to the printer while fitting the tabs on the left side cover into the slots of the

printer enclosure. Place the cables avoiding the protrusions on the left side cover. Especially, be

careful of the protrusion E on the cover for the B-EP2DL series.

B-EP4DL Series: Fit the tabs A to D into the slots A’ to D’.

B-EP2DL Series: Fit the tabs A to C into the slots A’ to C’.

NOTE: It is easy to mount the left side cover if you fit the tabs from the LCD side in order, then secure the

bottom side. Be careful not to catch the cable by the cover while reassembling.

Tab

Tab B Tab C Tab D

’

B’

C’

D’

Tab

Tab C

Tab B

’

B’

C’

Left Side Cove

Protrusion

6/8

Step12. Mount the right side cover to the printer while fitting the tabs on the right side cover into the slots of the

printer enclosure.

B-EP4DL Series: Fit the tabs A to C into the slots A’ to C’.

B-EP2DL Series: Fit the tabs A to C into the slots A’ to C’.

NOTE: It is easy to mount the right side cover if you fit the tabs from the LCD side in order, then secure the

bottom side. Be careful not to catch the cable by the cover while reassembling.

Tab A

Tab BTab C

’

B’

C’

Tab A

Tab B

Tab C

’

B’

C’

Right Side Cover

7/8

Step13. Close the top cover and load the battery pack.

Step14. Attach the supplied Standard Label to the following position.

Step15: Configure the Bluetooth module settings in the system mode with reference to the Key Operation

Specification or Service manual.

For how to configure the Bluetooth Module settings by the B-EP Setting Tool, please refer to B-EP

Setting Tool Operation Manual.

Precautions for Handling of Wireless Communication Devices

Bluetooth® Module: TEC-BTM-R (B-EP700-BLTH-QM-R)

Trade Mark

Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. and used byTOSHIBA TEC CORPORATION under

license.

Cautions

General

For all countries and areas

This product is a wireless communication device, and the use of thisproduct is restricted to the following countries or

areas. If the product isused in the countries or areas other than the following, you may bepunished according to the laws

of those countries or areas.

USA, Canada, Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany,

Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania,

Slovakia, Slovenia, Spain, Sweden, United Kingdom, Switzerland, Norway, Iceland, Liechtenstein, Australia,

New Zealand, Mexico

For Europe

for Bluetooth

Hereby, TOSHIBA TEC CORPORATION, declares that the TEC-BTM-R is in compliance with the essential requirements

and other relevant provisions of Directive 1999/5/EC. This equipment uses a radio frequency band that has not been

harmonized throughout all EU and EFTA countries, and can be used in EU and EFTA countries.

For USA

This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, includinginterference that may cause undesired operation.

Changes or modification not expressly approved by manufacturer forcompliance could void the user’s authority to

operate the equipment.

Standard Label Standard Label

B-EP2DL Series

B-EP4DL Series

8/8

For Canada

Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device.

To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from

windows to provide maximum shielding. Equipment that is installed outdoors is subject to licensing.

For safety

Do not use this product in locations where use may be forbidden, for example,in an aeroplane or a hospital. If you do not

know the forbidden areas, please referto and follow the airline company or medical institution guidelines.

Flight instrument or medical equipment may be affected, causing a serious accident.

Since this product uses extremely low power compared with mobile phones, itcannot possibly interfere the pacemakers

and defibrillators. However, if the useof this product should be likely to have affected the pacemaker or

defibrillator,immediately stop using the product and contact your TOSHIBA TEC sales agent.

Do not disassemble, modify, or repair the product. Doing so may cause injury. Also, modification is against the Laws

and Regulations for Radio Equipment. Please ask your TOSHIBA TEC sales agent for repair.

Precaution in use

This product communicates with other devices by radio. Depending on the installation location, orientation, environment,

etc., its communication performance may deteriorate or devices installed near by may be affected.

Keep away from a microwave.

Communication performance may deteriorate or a communication error may occur due to the radio emitted from a

microwave.

Since the Bluetooth and wireless LAN use the same radio frequency band, each radio wave may interfere with each

other when they are used at the same time, causing a deterioration of communication performance or a disconnection of

network. If there is any problem with connection, please stop using either Bluetooth or wireless LAN.

Do not use the product on a metal table or near a metal object.

Communication performance may be deteriorated.

TEC-BTM-R Specification

• Bluetooth class 2

• Built-in protocol stack activated by Bluetooth V1.2 serial port profile

• Operating temperature (When installed to the printer): -5 to 50°C, 25% to 85%RH (No condensation)

• Dimensions: 38.1 mm (W) x 25.4 mm (H) x 7 mm (D)

PRINTED IN SINGAPORE

EO2-38061

Inhaltsverzeichnis

Andere Toshiba Steuereinheit Handbücher

Toshiba

Toshiba MMW-UP0271LQ-E Bedienungsanleitung

Toshiba

Toshiba B-8204-QM-R Bedienungsanleitung

Toshiba

Toshiba BMS-SM1280HTLE Bedienungsanleitung

Toshiba

Toshiba Carrier RBM-A0601UPVA-UL Bedienungsanleitung

Toshiba

Toshiba IK-CU43A Bedienungsanleitung

Toshiba

Toshiba IK-TF9U Bedienungsanleitung

Toshiba

Toshiba Adjustable Speed Drive H7 Series Bedienungsanleitung

Toshiba

Toshiba HX7 Series Bedienungsanleitung

Toshiba

Toshiba TC Series Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-MB1 Bedienungsanleitung

Toshiba

Toshiba V Series Bedienungsanleitung

Toshiba

Toshiba MD911 Bedienungsanleitung

Toshiba

Toshiba G3 Plus Pack Bedienungsanleitung

Toshiba

Toshiba G3 Plus Pack Bedienungsanleitung

Toshiba

Toshiba BMS-SM1280HTLE Bedienungsanleitung

Toshiba

Toshiba IK-CT2D Bedienungsanleitung

Toshiba

Toshiba LONWORKS LIU007Z Bedienungsanleitung

Toshiba

Toshiba IK-4KE Bedienungsanleitung

Toshiba

Toshiba nv Series Bedienungsanleitung

Toshiba

Toshiba nv Series Bedienungsanleitung

Toshiba

Toshiba nv Series Bedienungsanleitung

Toshiba

Toshiba GN-4020 Bedienungsanleitung

Toshiba

Toshiba LTD121EA43G Bedienungsanleitung

Toshiba

Toshiba IK-HR1CD Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung