Toshiba TRST-A10 SERIES Bedienungs- und Wartungsanleitung
1
Quick Installation Manual
This sheet contains only the quick Installation procedures. Please be
sure to read the Owner’s Manual in the web site for further
information about this printer.
Important Information to the User
In order to meet Product Safety, FCC and CE marking requirements, it is advised
to use the power supply, power cord, and interface cable which were shipped with
this product. Otherwise these devices need to meet following standards.
Power Supply
The power supply should follow UL/EN/IEC60950-1 certification, Class I power
supply with SELV (Secondary Extra Low Voltage), non-energy hazard output,
limited power source, input rated 100-240 Vac, 1.5/0.8 A, 50/60 Hz, output rated
24 Vdc, 3.15A.If this product is used with a power supply different from the
Toshiba TEC power supply, you will need to test this power supply and the
Toshiba TEC printer to comply to FCC and CE mark certification.
Interface Cable
You are advised to use a shielded (360 degree) interface cable with this product.
The shield must be connected to the frame or earth ground connection or earth
ground reference at BOTH ends of the cable.
If another cable is used than described above you will need to test this cable with
the Toshiba TEC printer and your system for FCC and CE mark certification.
Power Cord
For this product a UL listed, detachable power cord is required. When the power
supply is mounted on the floor, a power cord with Type SJT marking is required.
Outside the US, power cords need to meet the particular country’s certification and
application requirements. If a power cord is used different from described above
you might violate safety certifications which are in force in the country of use. The
socket-outlet needs to be installed near the equipment and must be easily
accessible.
TOSHIBA REMOTE RECEIPT PRINTER
TRST-A10 SERIES
2
1. Front/Rear View
Front View Rear View
2. LED and Feed Button
POWER LED (Green)
Lights when the power is turned
on.
ERROR LED (Blinking Green)
The Error LED indicates an error
by blinking
FEED Button
Used to feed receipt paper. A
touch of this button causes one
line feed. Pressing and holding it
feeds the paper continuously.
When the power switch is turned
on while the [FEED] button is
pressed and held, the printer will
perform a self test print
Feed Button
Printer
Cover
LED
Power Switch
Top Cover
3
3. Loading the Receipt Roll
When you use this printer for the first time or when the receipt paper has been used up,
load a receipt roll in the following procedures while the printer power is set to ON. A
thermal printer prints thermal receipt paper by applying heat to the paper to react with
the chemicals on the paper surface. A red line which appears on the reverse side of
the receipt paper indicates that the paper is almost used up.
WARNING!
The print
head
becomes
very hot
while
printing.
Never
touch the
print head
to avoid
getting
burned.
Hazardous
moving
cutter.
Keep
fingers and
other body
parts
away.
Standard operating temperature of printer is 5oC to 50 oC. Please do not operate out of
range for safe operation.
Cutter
Print Heads
4
1) Turn the printer power ON.
2) Hold the raised sides firmly and lift upwards to unhook the printer cover. (1)
3) Hold both sides of the printer cover and open it until it stops. (2)
4) Check for the correct orientation of the receipt roll, and put it into the paper
holder.
Pull the receipt until it extends past the paper outlet for about 5 cm (3), and then
close the printer cover by pressing it’s front center gently until a positive lock is felt.
CAUTION!
1. Use only TOSHIBA TEC specified paper. Use of non-specified paper may
shorten the print head life resulting in problems with print quality, cause a paper
feed failure, or shorten the cutter life.
2. Do not subject the thermal receipt roll to water, oil, or heat source as this will
darken the paper.
3. Load the receipt roll in the correct orientation. Failure to do this may cause a
paper jam error.
4. Care must be taken not to damage the print head and platen when the printer
cover is opened as this may cause a poor print or a printer failure.
5. Do not open the printer cover while the printer is printing.
6. Do not hold the receipt while the printer is printing. Doing so may cause a paper
jam.
7. When closing the printer cover, do not press it down too hard.
8. Do not put anything on the printer cover or push the cover too strongly. Doing so
may cause a print failure.
1
2
3
Raised
ed
g
e
Print Cover
Receipt Roll
5
4. Receipt Roll
Paper type Thermal paper rolled with the print side facing outside
Width (W1) 80 +/ -1.0 mm
Width (W2) 58 +0/ -1.0 mm (With optional 58 mm paper guide)
Outer diameter (D) 76 +/-2.0 mm
Paper thickness (T) 0.065 +/- 0.005 mm
Weight 53 g/m2
Outer core diameter 21.5 mm
Inner core diameter 12.5 +/- 0.5 mm
Recommended thermal
paper Only paper rolled onto a core is acceptable, however, the
paper end should not be pasted to the core. TOSHIBA
TEC recommends using the following thermal paper for
this product.
Manufacturer : OJI
Type : JFD210
CAUTION!
Use only paper which meets specified requirements. Use of non-specified paper may
shorten the head life of the printer, resulting in problems with print quality, cause a paper
feed failure or shorten the cutter life. All paper should be handled with care to avoid any
damage to the paper. Read the following guideline carefully.
• Do not store the paper for longer than the manufacturer’s recommended shelf life.
• Store the paper in a cool, dry place. Avoid areas where they would be exposed to direct
sunlight, high temperature, high humidity, dust or gas.
• A contact of chemical or oil may discolor or erase the printed record.
• Rubbing the paper hard with nail or hard object may discolor the paper.
• The paper end should not be pasted to the core.
For further information please contact your authorized TOSHIBA TEC representative or
authorized paper manufacturer.
W1 or W2
E
PRINTED IN SINGAPORE
EO1-13020
< For EU only >
TOSHIBA TEC Europe Retail
Information Systems S.A
Rue de la Célidée 33 BE-1080
Brussels
www.toshibatec-eu.com
C
opyr
i
g
ht
©
200
7
by TOSHIBA TEC CORPORATION
A
ll Rights Reserved
570 Ohito, Izunokuni-shi, Shizuoka-
ken, JAPAN
Andere Handbücher für TRST-A10 SERIES
6
Inhaltsverzeichnis
Andere Toshiba Drucker Handbücher
Toshiba
Toshiba B-EP4DL Series Bedienungsanleitung
Toshiba
Toshiba TEC B B-SX5T SERIES Bedienungsanleitung
Toshiba
Toshiba B-570 Bedienungsanleitung
Toshiba
Toshiba E-STUDIO E-Studio 3511 Service-Handbuch
Toshiba
Toshiba B-SX5T Series Technische Daten
Toshiba
Toshiba B-SX6T Series Bedienungsanleitung
Toshiba
Toshiba TRST-A10 SERIES Bedienungsanleitung
Toshiba
Toshiba B-SA4TM SERIES Bedienungsanleitung
Toshiba
Toshiba 1TN Bedienungsanleitung
Toshiba
Toshiba B-SA4TP SERIES Bedienungsanleitung
Toshiba
Toshiba es525p Bedienungsanleitung
Toshiba
Toshiba B-852 Series Bedienungsanleitung
Toshiba
Toshiba GA-1310 Bedienungsanleitung
Toshiba
Toshiba e-STUDIO400P Konfigurationshandbuch
Toshiba
Toshiba e-STUDIO 207L Bedienungsanleitung
Toshiba
Toshiba e-STUDIO165 Bedienungsanleitung
Toshiba
Toshiba B-FV4D-GS12-QM-R Bedienungsanleitung
Toshiba
Toshiba B-480-QQ Bedienungsanleitung
Toshiba
Toshiba B-EP2DL Series Bedienungsanleitung
Toshiba
Toshiba B-SA4TM-GS12 Bedienungsanleitung
