Toshiba RBC-AMT32E Bedienungsanleitung

163

Wired remote controller (RBC-AMT32E)

Operation manual

PartsName of Remote Controller

Display section

In the display example, all indicators are displayed for the explanation.

In reality only, the selected contents are indicated.

• When turning on the main power switch and leak breaker at the first

time,

SETTING

flashes on the display part of the remote controller.

• While this display is flashing, the model is being automatically

confirmed.

Accordingly, wait for a while after

SETTING

display has disappeared, and

then use the remote controller.

1SETTING display

Displayed during setup of the timer etc.

2Operation mode select display

The selected operation mode is displayed.

3CHECK display

Displayed while the protective device works or a

trouble occurs.

4Timer time display

Time of the timer with H mark is displayed.

(When a trouble occurs, the check code is

displayed.)

5Timer SET IN setup display

When pushing the Timer SET IN button, the

display of the timer is selected in order of

[OFF] [OFF] repeat OFF timer

[ON] No display.

6Filter display

If “FILTER ” is displayed, clean the air filter.

7TEST run display

Displayed during a test run.

8Louver position display

(4-way Air Discharge Cassette,

2-way Air Discharge Cassette,

1-way Air Discharge Cassette, Under Ceiling

and High Wall Type only (2H. 3H))

Displays louver position.

9SWING display

Displayed during up/down movement of the louver.

10 Set up temperature display

The selected set up temp. is displayed.

11 Remote controller sensor display

Displayed while the sensor of the remote

controller is used.

12 PRE-HEAT display (Heat-pump model only)

Displayed when the heating operation starts or

defrost operation is carried out.

While this indication is displayed, the indoor fan

stops or the mode enters in LOW.

13 No function display

Displayed if there is no function even if the

button is pushed.

Display

section

Operation

section

TIME

TIMER SET

TEST

FIL

TER

RESET

WING/FI

VENT

MODE

OFF

UNIT

LOUVER

920 19

715

13 12

This remote controller can control

the operation of Max. 8 indoor units.

164

14 Air volume select display

The selected air volume mode is displayed.

(AUTO) (HIGH)

(MED.) (LOW)

15 Louver Number display

(exapmle:01, 02, 03, 04)

16 Operation ready display

Displayed when cooling or heating operation is

impossible because the outdoor temperature

goes out of the operable range.

17 Mode select control display

Displayed when pushing “Operation mode select

” button while the operation mode is fixed to

heating or cooling by the system manager of the

air conditioner.

18 Louver lock display

(4-way Air Discharge Cassette Type

2H series only)

Displayed when there is a louver-locked unit in the

group (including 1 indoor unit by 1 outdoor unit).

19 Unit Number display

Unit number of the indoor unit selected with

the unit select button or abnormal indication of

the indoor/outdoor unit.

20 Central control display

Displayed when the air conditioner is used

under the central control in combination with a

central control remote controller.

In case the remote controller is disabled by the

central control system, flashes.

The button operation is not accepted.

Even when you push ON/OFF, MODE, or

TEMP. button, the button operation is not

accepted.

(Settings made by the remote controller vary

with the central control mode. For details, refer

to the Owner’s Manual of the central control

remote controller.)

920 19

715

13 12

165

Operation section

Push each button to select a desired operation.

• The details of the operation needs to be set up once, afterward, the air conditioner can be used by pushing

ON / OFF

button only.

FAN

button (Air volume select button)

Selects the desired air volume mode.

TIMER SET

button (Timer set button)

TIMER SET button is used when the timer is set up.

TEST

button (Check button)

The CHECK button is used for the check operation.

During normal operation, do not use this button.

VENT

button (Ventilation button)

Ventilation button is used when a fan which is

sold on the market is connected.

• If “No function ” is displayed on the remote

controller when pushing the Ventilation button, a

fan is not connected.

FILTER

RESET

button (Filter reset button)

Resets (Erases) “ FILTER” display.

SAVE

button (Power save operation)

SWING/FIX

button (Swing/Wind direction button)

Selects automatic swing or setting the louver

direction.

• This function is not provided to Concealed Duct

Standard Type, High Static Pressure Type,

Floor Standing Cabinet Type, Floor Standing

Concealed Type, or Slim Duct Type.

8Operation lamp

Lamp is lit during the operation.

Lamp is off when stopped.

Also it flashes when operating the protection

device or abnormal time.

ON / OFF

button

When the button is pushed, the operation starts,

and it stops by pushing the button again.

When the operation has stopped, the operation

lamp and all the displays disappear.

MODE

button (Operation mode select button)

Selects desired operation mode.

UNIT LOUVER

button (Unit/Louver select button)

Selects a unit number (left) and louver number

(right).

UNIT:

Selects an indoor unit when adjusting wind

direction when multiple indoor units are

controlled with one remote controller.

LOUVER (4-way Air Discharge Cassette

Type 2H series only):

Selects a louver when setting louver lock or

wind direction adjustment independently.

TEMP.

button (Set up temperature button)

Adjusts the room temperature.

Set the desired set temperature by pushing

TEMP. or TEMP. .

OPTION :

Remote controller sensor

Usually the TEMP. sensor of the indoor unit senses

the temperature. The temperature on the surrounding

of the remote controller can also be sensed.

For details, contact the dealer from which you have

purchased the air conditioner.

• In case that one remote controller controls the

multiple indoor units, the setup operation is unavail-

able in group control.

TIME

TIMER SET

TEST

FIL

TER

RESET

TEMP

WING/FI

VENT

MODE

ON / OFF

UNIT

LOUVER

166

Correct Usage

• When you use the air conditioner for the first time or when you change the SET DATA value, follow the

procedure below. From the next time, the operation displayed on the remote controller will start by pushing the

ON / OFF

button only.

Preparation

Turn on the main power switch and/or the leakage breaker.

• When the power supply is turned on, a partition line is displayed on the display part of the remote controller.

After the power supply is turned on, the remote controller does not accept an operation for approx. 1 minute,

but it is not a failure.

REQUIREMENT

• While using the air conditioner, operate it only with

ON / OFF

button without turning off the main power switch

and the breaker.

• When you use the air conditioner after it has not been used for a long period, turn on the power switch at least

12 hours before starting operation.

Start

Push

ON / OFF

button.

The operation lamp goes on, and the operation

starts.

Select an operation mode with the

“MODE

MODE

” button.

One push of the button, and the display changes

in the order shown as follows.

• “

DRY mode” function is not provided to

Concealed Duct High Static Pressure Type.

Select air volume with “

FAN

” button.

One push of the button, and the display changes

in the order shown as follows.

• When air volume is “

AUTO”, air volume

differs according to the room temperature.

• In

DRY mode, “

AUTO” is displayed and

the air volume is LOW.

• In heating operation, if the room temperature is

not heated sufficiently with VOLUME “ LOW”

operation, select “

MED.” or “

HIGH”

operation.

• The temperature sensor senses temperature near

the air inlet of the indoor unit, which differs from

the room temperature depending on the installa-

tion condition.

A value of setting temperature is the measure of

room temperature.

(“

AUTO” is not selectable in the FAN mode.)

• Air volume of function is not provided to

“Concealed Duct High Static Pressure Type” but

air speed “

HIGH” only is displayed.

Determine the set up temperature by pushing

the “TEMP.

” or “TEMP. ” button.

Stop

Push

ON / OFF

button.

The operation lamp goes off, and the operation stops.

HEAT

DRY COOL FAN

Heat-pump model

DRY COOL FAN

Cooling only model

(Dehumidify)

UTO HIGH MED. LOW

TIME

TIMER SET

TEST

FIL

TER

RESET

TEMP

WING/FI

VENT

MODE

ON / OFF

UNIT

LOUVER

167

[In case of cooling]

• Start the cooling operation after approx. 1 minute.

[In case of heating (For Heat-pump model only)]

• The heating operation mode is selected in accordance with the room temperature and operation starts after

approximately 3 to 5 minutes.

• After the heating operation has stopped, FAN operation may continue for approx. 30 seconds.

• When the room temperature reaches the set temperature, the super low wind is discharged and the air volume

decreases excessively.

• During defrost operation, the fan stops so that cool air is not discharged. (“

PRE-HEAT” is displayed.)

NOTE

When restarting the operation after stop

• When restarting the operation immediately after stop, the air conditioner does not operate for approx.

3 minutes to protect the machine.

For best cooling and heating performance, adjust the louvers (adjustment of up/down wind direction) appropriately.

CAUTION

• If cooling operation is performed with downward air outlet, dew may fall on surface of the cabinet or the

horizontal louver resulted in dripping.

• If heating operation is performed with horizontal air outlet, unevenness of temperature may increase in the room.

• Do not move the horizontal louver directly with hands; otherwise a trouble is caused.

Select direction of the horizontal louver using

SWING/FIX

switch on the remote controller.

The horizontal louver does not stop immediately even if the switch is pushed.

Adjusting the stop position, push the switch.

For all models

[In Cooling operation]

Use the louvers with horizontal set point.

[In Heating operation (For Heat-pump model only)]

Use the louvers with downward set point.

For Under Ceiling, 1-way Air Discharge Cassette, High Wall Type

[Right / Left air direction adjustment]

To change the air outlet direction to right or left side, set the vertical louver inside of the horizontal louver to the

desired direction.

Adjustment of Wind Direction

Andere Handbücher für RBC-AMT32E

Inhaltsverzeichnis

Andere Toshiba Fernbedienung Handbücher

Toshiba

Toshiba RB-RWS21-E Bedienungsanleitung

Toshiba

Toshiba WH-H1JE2 Bedienungsanleitung

Toshiba

Toshiba RBC-ASC11E Bedienungsanleitung

Toshiba

Toshiba RB-RWS21-E Bedienungsanleitung

Toshiba

Toshiba RBC-AMS54E-ES Bedienungsanleitung

Toshiba

Toshiba RBC-AMS51E-EN Bedienungsanleitung

Toshiba

Toshiba RBC-AS21UL Bedienungsanleitung

Toshiba

Toshiba RBC-AX31U-UL Bedienungsanleitung

Toshiba

Toshiba RBP-RC001-E Betriebsanleitung

Toshiba

Toshiba TCB-AX21U-E Bedienungsanleitung

Toshiba

Toshiba RB-RXS33-E Bedienungsanleitung

Toshiba

Toshiba RBC-SR1-PE Bedienungsanleitung

Toshiba

Toshiba RBC-AX32UW-UL Bedienungsanleitung

Toshiba

Toshiba RBC-AX23UWW-E Bedienungsanleitung

Toshiba

Toshiba TCB-AX21E Bedienungsanleitung

Toshiba

Toshiba MML-AP0074NH-E Bedienungsanleitung

Toshiba

Toshiba RBC-AWSU52-UL Bedienungsanleitung

Toshiba

Toshiba RBC-AMT32E Bedienungsanleitung

Toshiba

Toshiba RBC-AMT31-E Bedienungsanleitung

Toshiba

Toshiba RG57A8/BGEF Bedienungsanleitung

Toshiba

Toshiba Lite-Vision plus RBC-AMS51E Bedienungsanleitung

Toshiba

Toshiba RBC-AMSU51 -ES Bedienungsanleitung

Toshiba

Toshiba CT-8003 Bedienungsanleitung

Toshiba

Toshiba RBC-AX32UM(W)-E Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung