TP-Link Auranet EAP120 Bedienungsanleitung

Quick Installation Guide

LED Indication

Hardware Overview

2Hardware Installation

Software Configuration

Power Supply

1Network Topology Requirement

A DHCP server (typically a router) is required to assign IP addresses to the EAP and clients in your local network.

A computer running the EAP Controller software, which can be in the same or different subnet with the EAPs.

Option 1: Ceiling Rail Mounting

Option 2: Ceiling Mounting

Option 3: Wall Mounting

The EAP can be ceiling rail mounted, ceiling-mounted, and wall-mounted.

The instructions for various mounting options are on the back of this Quick Installation Guide.

The device is working properly.

Solid green

System errors. RAM, Flash,

Ethernet, WLAN or firmware

may be malfunctioning.

Flashing red

The device is being reset to its

factory default settings.

Double-flashing red, green, yellow

Firmware update is in progress.

Do not disconnect or power off

the device.

Flashing yellow

RESET ON/OFF POWER

CONSOLE ETHERNET

Interface Panel

RESET

With the device powered on, press and hold the button for about 8 seconds until the LED flashes red, then

release the button. The device will restore to factory default settings.

CONSOLE

The port is used to connect to the serial port of a computer or a terminal to check and monitor system information

of the EAP device.

CLI commands are not available in current software version. We will release a new version supporting CLI

commands soon. Please pay close attention to our official website.

The port is used to connect to a router or a switch to transmit data or to a PSE (Power Sourcing Equipment),

such as a PoE switch, for both data transmission and Power over Ethernet (PoE) through Ethernet cabling.

ETHERNET

Press this button to turn on or turn off the EAP device.

ON/OFF

EAP can be powered via a PSE device (such as a PoE switch) or a power adapter.

Via Power Adapter

1. Plug one end of the provided power adapter into the POWER port of the EAP and the other end to a standard

electrical wall outlet.

2. Press the ON/OFF button on the interface panel of the EAP.

1. Connect the Ethernet cable from the PoE switch to the ETHERNET port.

Via PoE Switch

PoE Switch Switch

ON/OFF

EAP120 / EAP220

7106505542 REV1.0.0

Clients

Switch

EAP

Controller Host

EAP Controller

Router

Internet

ON/OFF

To quickly set up a wireless network connection with mass EAPs, please follow the steps below.

For More Configurations

Now you can manage your wireless network and view network statistic using the EAP Controller. Please refer

to the EAP Controller User Guide to learn more information on configuring and using the Controller software.

Find the EAP Controller application file on the Resource CD (for Windows user only) or from our website at

www.tp-link.com. Run the file and follow the wizard to install the EAP Controller on the computer.

Step 1: Installing the EAP Controller

Launch the EAP Controller and follow the configuration wizard to create a primary wireless network. After the wizard

is finished, a login screen will appear. Enter the admin name and password you created and click Sign In.

Step 2: Configuring the EAP Controller

Adopt the EAP devices in the Controller management interface to change the status from pending to connected.

Step 3: Adopting the EAP devices

Note: The IP address of the management computer must be reachable for the EAPs in the network.

Option 1: Ceiling Rail Mounting Option 3: Wall Mounting

Option 2: Ceiling Mounting

M3×20 Self-tapping Screws

(Qty.3)

M3×28 Plastic Wall Anchors

(Qty.3)

Connect the Ethernet cable to the ETHERNET port on

the EAP.

Feed the Ethernet cable through the hole and set the

ceiling tile back into place. Connect the Ethernet

cable to the ETHERNET port.

Connect the Ethernet cable to the ETHERNET port.

Make two small pencil marks on the wall. Make sure

the two marks are level and should be 98.6mm apart.

Drill two 6mm holes through the center of your marks.

Place the mounting bracket in the center of the ceiling

tile. Mark the three positions of the screw holes and a

10mm hole for the Ethernet cable to feed through.

Drill three 4mm holes and a 10mm hole for the Ethernet

cable.

Use an M3×6 pan-head screw to secure the T-rail Clip

onto the ceiling rail.

Position the Ceiling T-rail Clip and push the movable

part toward the rail base.

Remove the ceiling tile.

Attach the EAP to the mounting bracket by aligning

ARROW 1 (on the EAP) with ARROW 2 (on the

mounting bracket), then rotate the EAP clockwise until

it locks into place.

Insert the plastic wall anchors into the 6mm holes and

drive the self-tapping screws into the anchors. Do not

drive the screws all the way in and leave enough

clearance to hang the EAP.

Secure the mounting bracket to the ceiling tile using

three M3x30 pan-head screws, washers and wing

nuts, as shown on the left.

Attach the mounting bracket to the Ceiling T-rail Clip

using four M3x6 pan-head screws.

Hang the EAP on the screws. Make sure the EAP is

firmly seated against the wall.

Attach the EAP to the mounting bracket by aligning

ARROW 1 (on the EAP) with ARROW 2 (on the

mounting bracket), then rotate the EAP clockwise until

it locks into place.

Attach the EAP to the mounting bracket by aligning

ARROW 1 (on the EAP) with ARROW 2 (on the

mounting bracket), then rotate the EAP clockwise until

it locks into place.

Ceiling T-rail Clip M3×6 Pan-head Screws

(Qty.5)

Hole for Ethernet cable

98.6mm

Wing Nuts

(Qty.3)

Washers

(Qty.3)

M3×30 Pan-head Screws

(Qty.3)

Andere Handbücher für Auranet EAP120

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere TP-Link Drahtloser Zugangspunkt Handbücher

TP-Link

TP-Link Deco Bedienungsanleitung

TP-Link

TP-Link 6935364097752 Bedienungsanleitung

TP-Link

TP-Link Omada EAP225 Bedienungsanleitung

TP-Link

TP-Link Omada TPL-EAP225 Bedienungsanleitung

TP-Link

TP-Link Deco E4/W2400 Bedienungsanleitung

TP-Link

TP-Link Omada Pro Bedienungsanleitung

TP-Link

TP-Link CPE605 Bedienungsanleitung

TP-Link

TP-Link AP200 Bedienungsanleitung

TP-Link

TP-Link AP500 Bedienungsanleitung

TP-Link

TP-Link Auranet EAP110 Bedienungsanleitung

TP-Link

TP-Link Omada EAP653 Bedienungsanleitung

TP-Link

TP-Link Auranet EAP330 Bedienungsanleitung

TP-Link

TP-Link TL-WA7110ND Bedienungsanleitung

TP-Link

TP-Link deco AC1300 Einrichtungshandbuch

TP-Link

TP-Link Omada EAP230-Wall Bedienungsanleitung

TP-Link

TP-Link TL-WA801N Bedienungsanleitung

TP-Link

TP-Link TL-WA1201 Bedienungsanleitung

TP-Link

TP-Link Omada Pro AP9670 Bedienungsanleitung

TP-Link

TP-Link AP300 Bedienungsanleitung

TP-Link

TP-Link PHAROS SERIES Bedienungsanleitung

TP-Link

TP-Link TL-WA901ND Bedienungsanleitung

TP-Link

TP-Link TL-WA7210N Bedienungsanleitung

TP-Link

TP-Link Auranet EAP320 Bedienungsanleitung

TP-Link

TP-Link Auranet EAP110 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung