TP-Link TL-WR940N Bedienungsanleitung

Note Please use onl

wired network connections to configure the Route

Turn off all of your network devices, including your computer, Modem and the

Router.

Connect your computer to the

Port labeled 1~4 on the Route

with an Ethernet cable.

Plug the provided Powe

dapter into the Power jack on

the back of the Router and the

other end to a standard

electrical wall socket.

Connect the WAN port on your

Router to the Modem’s LAN

port with an Ethernet cable.

WAN: Flashing or solid light

Turn on all of your network devices and then check to see if the LEDs of the

Router display normally as the digram below describes.

Note To configure the device, you can either run the Resource CD (method one),

or run the Web-based Quick Setup Wizard (method two). TP-LINK strongly

recommends that you run the Resource CD.

LAN: Flashing or solid light if the

corresponding port is connected

Note If the LEDs display abnormally, please check to see if all the cable

connectors (power adapter and Ethernet cable) are well connected to you

device.

SYS/WLAN: Flashing

PWR: Solid light

The configuration has now been completed. Please skip to step 3 Testing the

Internet Connection.

Insert the provided Resource CD

into your CD-ROM drive.

The Easy Setup Assistant

will automatically prompt you

on your computer’s screen.

Click START, and then follow

the step-by-step instructions

until you complete the

configuration

Please select your

product model and click

Easy Setup Assistant

A dialog box will prompt you fo

the User name and Password.

Enter the default values and click

OK.

Note If the dialog box does not pop up, please refer to T3 in the

Troubleshooting guide. T2 will help you if you forget the password.

The web management page will

display after a successful login.

Open your web browser, type

http://tplinklogin.net in the

address field and press Enter

Click Quick Setup

User name: admin

Password: admin

Click OK

Internet Parameters Configuration

A Configuration for PPPoE

Note

This page will then display.

fter completing the above configuration, please skip to Wireless Settings

Configuration.

Wait for the Router to detect the

connection type.

If PPPoE is detected, the screen will pop up as shown in A. Please proceed to AǗ

If Static IP is detected, the screen will pop up as shown in B. Please skip to BǗ

If Dynamic IP is detected, the screen will pop up as shown in C. Please skip to C.

1. Make sure the cable is securely plugged into the WAN port before

detection.

2. If the connection type your ISP provided is PPTP, L2TP or BigPond (o

Heart Beat Signal), you must go to “Network > WAN” to configure you

connection type manually.

Click Next

Select

Click Next

Enter the Username and

Password provided by your ISP

Click Next

B Configuration for Static IP

C Configuration for Dynamic IP

fter completing the above configuration, please proceed to Wireless Settings

Configuration.

This page will then display.

Click Next

Enter the IP Address,

Gateway, DNS provided

our ISP manuall

This page will then display.

Note 1.It’s strongly recommended that you visit and configure the Router from the

main computer.

2.To find the main computer’s MAC, please go to Start > Run on your main

computer, type in cmd and press Enter. At the command prompt, ente

ipconfig/all and press Enter. The MAC will be displayed under Physical

Address.

Click Clone MAC Address

Click Next

If you are visiting the Router

from the main computer,

please select

Enter the main computer’s MAC

in the field WAN MAC Address

Click Next

If you are visiting the Router

from another computer, rather

than the main computer, please

select No

After completing the above configuration, please proceed to Wireless Settings

Configuration.

Wireless Settings Configuration

Or if wireless settings have been changed

Note The wireless security has not yet been configured in the above steps. You

are suggested to finish this configuration first and then refer to

ppendix

Wireless Security Setup to configure the wireless security.

This page will then display.

Keep the default setting:

Enable Wireless. If you want

to disable wireless, please

select Disable

Select your region from the drop-down list

Click Next

Click Finish

Click Reboot

Create a unique and easy-to-remember

name for your wireless network.

You can also keep default settings

without the device bein

affected.

Note

The basic settings for your Router are completed. Please open the web browser and

log on to the following websites:

http://www.tp-link.com

http://www.google.com

If the above websites can be accessed, it indicates that your Router has been

configured successfully and you can begin to enjoy the Internet. If the website

cannot be accessed, please refer to “T4. What can I do if I cannot access the

Internet?” in the Troubleshooting guide.

The above configurations only need to be set once. If you want other

computers in your network to access the Internet, please connect the desired

computer to the router directly. If the additional computer can not access the

Internet, please set that computer referring to “T3. What can I do if I cannot

access the web-based configuration page?” in the Troubleshooting

guide.

For advanced configurations, please refer to the User Guide on the

Resource CD provided.

Note

T1. How do I restore my Router’s configuration to its factory default

settings?

T2. What can I do if I don’t know or forget my password?

1) Restore the Router’s configuration to its factory default settings. If you don’t

know how to do that, please refer to section T1.

2) Use the default user name and password: admin, admin.

3) Try to configure your Router once again by following the instructions in the

previous steps of the QIG.

T3. What can I do if I cannot access the web-based configuration page?

1) Configure your computer’s IP Address.

For Windows XP OS

Go to Start > Control Panel,

you will then see the following

page.

With the Router powered on,

press and hold the RESET button

on the rear panel for 8 to 10

seconds before releasing it.

Once the Router is reset, the current configuration settings will be lost and

you will need to re-configure the router.

1 2 3 4

WAN

RESET

POWER

Click Network and Internet

Connections

Hold it for 8 to 10 seconds

Click Network

Connections

Right-click Local

Area Connection

Click Properties

Double-click Internet

Protocol (TCP/IP)

Andere Handbücher für TL-WR940N

Inhaltsverzeichnis

Andere TP-Link WLAN-Router Handbücher

TP-Link

TP-Link TD-W8961ND Bedienungsanleitung

TP-Link

TP-Link TD-W8951NB Bedienungsanleitung

TP-Link

TP-Link TL-WR710N Bedienungsanleitung

TP-Link

TP-Link TD-W9970 Bedienungsanleitung

TP-Link

TP-Link TX-W6961N Bedienungsanleitung

TP-Link

TP-Link TL-WR720N Bedienungsanleitung

TP-Link

TP-Link Archer D5 Bedienungsanleitung

TP-Link

TP-Link TD-W8901N Bedienungsanleitung

TP-Link

TP-Link ARCHER-C6U Bedienungsanleitung

TP-Link

TP-Link Archer AX3200 Bedienungsanleitung

TP-Link

TP-Link Archer C7 Bedienungsanleitung

TP-Link

TP-Link TL-WR820N Bedienungsanleitung

TP-Link

TP-Link AC1350 Bedienungsanleitung

TP-Link

TP-Link TL-WPA4220 TKIT Bedienungsanleitung

TP-Link

TP-Link Kasa Smart KP200 Bedienungsanleitung

TP-Link

TP-Link TL-WR710N Bedienungsanleitung

TP-Link

TP-Link Archer AX3000 Bedienungsanleitung

TP-Link

TP-Link TL-WA830RE Bedienungsanleitung

TP-Link

TP-Link RE210 Bedienungsanleitung

TP-Link

TP-Link ARCHER MR200 Bedienungsanleitung

TP-Link

TP-Link td-w8970 Bedienungsanleitung

TP-Link

TP-Link TL-WR1043ND Bedienungsanleitung

TP-Link

TP-Link Archer AXE300 Bedienungsanleitung

TP-Link

TP-Link AX75 V1 Bedienungsanleitung

Beliebte WLAN-Router Handbücher anderer Marken

Milesight

Milesight UG67 Bedienungsanleitung

Airlogic

Airlogic AirSync Class 1 Betriebsanleitung

Samsung

Samsung WCH730B Bedienungsanleitung

TELEFONICA

TELEFONICA USB Adapter Bedienungsanleitung

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Bedienungsanleitung

Askey

Askey RAC2V1K Bedienungsanleitung

Alloy

Alloy WLF2454AP-S Bedienungsanleitung

NETGEAR

NETGEAR WNR2000v4 Bedienungsanleitung

Hama

Hama 53120 Bedienungsanleitung

Intellinet

Intellinet 524582 Bedienungsanleitung

Asus

Asus RT-N10P Bedienungsanleitung

D-Link

D-Link DIR-506L Bedienungsanleitung

Sapido

Sapido GR297n Bedienungsanleitung

Asus

Asus DSL-N55U Bedienungsanleitung

AMTC

AMTC WR7502 Bedienungsanleitung

Compaq

Compaq CP-2W - iPAQ Connection Point Bedienungsanleitung

SMC Networks

SMC Networks WBR14-N2 FICHE Bedienungsanleitung

Draytek

Draytek Vigor2120 Series Bedienungsanleitung