Travis Industries Arbor Bedienungsanleitung

Leyden / Arbor Firebox Parts Installation

(see part numbers below)

Page 1 of 4 Printed 6/24/08 © Travis Industries, Inc.

Overview

This instruction sheet details installation of the three components listed below. Follow the instructions for to

the component being replaced. Refer to the exploded view diagram for parts reference and overview.

Packing List

Combustor Brick (250-00141)

•Combustor Brick

•Combustor Brick Gasket

•Interram Gasket

Back Plate (250-00704)

•Back Plate

•(2) Push Plugs

•(4) ¼-20 1-1/2” Bolts

•(4) ¼-20 Brass Nuts

Combustor (250-00247)

•Combustor (with gaskets

attached)

Exploded View Diagram

ID # Description Qty Part # ID # Description Qty Part #

1 Side Brick 2 250-00139 2 Combustor Brick w 2 Gaskets 1 250-00141

3 Inter-Ram Gasket 1 250-00294 4 Combustor Brick Gasket 1 250-00145

5 Back Brick 1 250-00140 6 Firebox Back w 4 Nuts & Bolts 1 250-00704

7 Brick Retainers with Bolts 1 250-00144 8 Combustor Pack with Gaskets 1 250-00247

9 Push Plugs (pack of 4) 2 92-1360



Apply penetrating oil (WD40) to the bolts

prior to removal to prevent stripping.

This nut is located on

the exterior of the stove

beneath the rear heat

shield.



Leyden / Arbor Firebox Parts Installation

(see part numbers below)

Page 2 of 4 Printed 6/24/08 © Travis Industries, Inc.

Combustor Brick Installation

The bolts inside the firebox may become difficult to remove after the stove has been burned. Apply

penetrating oil (WD40™) to the bolts 5 minutes prior to removal to prevent stripping or breaking the bolts.

1. Remove the side bricks and retainers (5/16” Nutdriver). See Figure 1.

2. Remove the back brick and retainer (7/16” Socket Wrench). See Figure 2.

Figure 1 Figure 2

3. Grasp the combustor brick with both hands and rotate it forward. See Figure 3. A ledge along the bottom

of the firebox floor helps hold the brick in place, make sure the brick clears this ledge while removing.

Figure 3

4. Before replacing the combustor brick, place the combustor brick gasket along the floor of the firebox,

making sure the slot in the gasket lines up correctly. Install the combustor brick and place the interram

gasket on top of it.

5. Replace the back and side bricks and retainers. You may wish to place high-temperature anti-seize on the

firebox bolts prior to installation to prevent the bolts from seizing.

Leyden / Arbor Firebox Parts Installation

(see part numbers below)

Page 3 of 4 Printed 6/24/08 © Travis Industries, Inc.

Back Plate Installation

1. Follow the instructions for removing the combustor brick (see page 2).

2. Remove the bypass ratcheting mechanism from the stove (see Figure 4). Remove the heat shield from the

back of the stove, exposing the four brass nuts holding the back plate in place (see Figure 5).

Figure 4 Figure 5

3. Unscrew the four screws holding the back plate in place (use a #3 Phillips screwdriver – See Figure 6). If

the bolts on the back of the stove begin to spin, use a wrench to secure.

Figure 6

4. When replacing the back plate, take care to prevent damage to the combustor. Tighten the bolts in an

alternating pattern (upper left, lower right, upper right, lower left) to prevent un-even tension on the plate.

When replacing the back

plate, place a thin bead

of furnace cement

around the perimeter of

the back plate to seal it.

Leyden / Arbor Firebox Parts Installation

(see part numbers below)

Page 4 of 4 Printed 6/24/08 © Travis Industries, Inc.

Combustor Installation

1. Follow the instructions for removing the combustor brick (see page 2).

2. Follow the instructions for removing the back plate (see page 3).

3. Apply penetrating oil (WD40™) to the two nuts holding the bypass assembly to the stove top and the two

bolts holding it to the back of the stove. Allow the oil to absorb for five minutes. Remove the two bolts with

a 7/16” socket wrench (see Figure 7). Remove the two nuts and washers along the stove top with a 7/16”

deep socket wrench. Hold the bypass plate in the closed position and carefully remove the bypass

assembly.

4. Remove the combustor from the firebox.

5. When replacing the combustor, make sure it is centered in the rear of the firebox (see Figure 8). Then re-

install the bypass, using one hand to hold the bypass plate closed while lifting the assembly into place. By

holding the bypass plate closed, it allows the bypass rod to engage the bypass correctly. Hold the bypass

in place and install the washers and nuts that install into the stove top (do not fully tighten at this time).

Take care to prevent damage to the combustor during bypass installation. Install the two bolts into the back

of the bypass assembly. Tighten the bolts in an alternating pattern, making sure the bypass is aligned

correctly. Tighten the nuts along the top in an alternating pattern to secure the bypass.

6. Replace the remaining firebox components (see pages 2 and 3).

Figure 7 Figure 8

Andere Handbücher für Arbor

Dieses Handbuch passt für folgende Modelle

Andere Travis Industries Kaminzubehör Handbücher

Travis Industries

Travis Industries Revolution 36CF Bedienungsanleitung

Travis Industries

Travis Industries Fireplace Xtrordinair GreenStart Apex 42 Bedienungsanleitung

Travis Industries

Travis Industries 564 EF-I Bedienungsanleitung

Travis Industries

Travis Industries Illuminations 4915 Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart DFC Montage- und Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart 2 Bedienungsanleitung

Travis Industries

Travis Industries Rosario DVS Face Bedienungsanleitung

Travis Industries

Travis Industries PB36CF Bedienungsanleitung

Travis Industries

Travis Industries ProBuilder 36 Bedienungsanleitung

Travis Industries

Travis Industries 96100593 Bedienungsanleitung

Travis Industries

Travis Industries 95400424 Bedienungsanleitung

Travis Industries

Travis Industries SKU 94400111 Bedienungsanleitung

Travis Industries

Travis Industries 616 DF Bedienungsanleitung

Travis Industries

Travis Industries 98500677 Bedienungsanleitung

Travis Industries

Travis Industries 98500668 Bedienungsanleitung

Travis Industries

Travis Industries Fireplace Xtrordinair 96300770 Bedienungsanleitung

Travis Industries

Travis Industries 4237 Bedienungsanleitung

Travis Industries

Travis Industries DVS EG Firebacks Bedienungsanleitung

Travis Industries

Travis Industries 96100110 Bedienungsanleitung

Travis Industries

Travis Industries 95600654 Bedienungsanleitung

Travis Industries

Travis Industries 96100212 Bedienungsanleitung

Travis Industries

Travis Industries 250-00128 Bedienungsanleitung

Travis Industries

Travis Industries GreenStart Igniter 3 Bedienungsanleitung

Travis Industries

Travis Industries 864 40K Bedienungsanleitung

Beliebte Kaminzubehör Handbücher anderer Marken

Valor

Valor L2 1700K Bedienungsanleitung

Exodraft

Exodraft Xzense Bedienungsanleitung

Whalen

Whalen Ruso MNFP62BF23-6 Bedienungsanleitung

Lopi

Lopi Hearthview 864 Bedienungsanleitung

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Bedienungsanleitung

EdilKamin

EdilKamin SERBATOIO 250 Kurzanleitung

Bronpi

Bronpi KIT-1 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Bedienungsanleitung

Superior

Superior ASD3628-TI Bedienungsanleitung

pleasant hearth

pleasant hearth OFP28WG Bedienungsanleitung

IHP

IHP Astria Series Bedienungsanleitung

Firegear

Firegear FG-H-2110SS Bedienungsanleitung

Nibe

Nibe Contura C i31 Bedienungsanleitung

kozy heat

kozy heat KZK-052 Bedienungsanleitung

SimpliFire

SimpliFire SF-WM36 Bedienungsanleitung

Bluegrass Living

Bluegrass Living BC18NR Kurzanleitung

pleasant hearth

pleasant hearth IRIS SCROLL Bedienungsanleitung

Cooke

Cooke Glass Wind Guard Bedienungsanleitung