Travis Industries 42 ProBuilder GSB2 Bedienungsanleitung

42 ProBuilder

GSB2

Owner’s Manual

WARNING: FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Leave the building immediately

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas supplier.

HOT GLASS WILL CAUSE

BURNS

DO NOT TOUCH GLASS

UNTIL COOLED

NEVER ALLOW CHILDREN

TO TOUCH GLASS

A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance

and shall be installed for the protection of children

and other at-risk individuals.

Tested and Listed by

Report # 0028GF105S

Omni-Test Laboratories, Inc.

Portland, Oregon

ANSI Z21.88-2016

CSA 2.33-2016

Operation

Maintenance

This appliance may be installed in an aftermarket, permanently located, manufactured home

(USA only) or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. A conversion

kit is supplied with the appliance.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Travis Industries, Inc. 12521 Harbour Reach Dr., Mukilteo, WA 98275 www.travisproducts.com

2 Table of Contents

Introduction

We welcome you as a new owner of a 42 ProBuilder GSB2 gas fireplace. This manual details operation

and maintenance of this fireplace. Please familiarize yourself with the Owner's Manual before operating

your heater and save the manual for future reference.

Important Information

No other 42 ProBuilder gas fireplace has the same

serial number as yours. The serial number is on the

listing label that is chained to the gas control valve.

This serial number may be needed in case you require

service.

Model: 42 ProBuilder GSB2

Serial Number:

Purchase Date:

Purchased From:

traviswarranty.com

Or, mail your warranty card to:

Travis Industries House of Fire

4800 Harbour Pointe Blvd. SW

Mukilteo, WA 98275

Save Your Bill of Sale.

To receive full warranty coverage, you will

need to show evidence of the date you

purchased your heater. Do not mail your Bill

of Sale to us.

We suggest that you attach your Bill of Sale

to this page so that you will have all the

information you need in one place should the

need for service or information occur.

Installation Warnings

Installation requirements are printed in the 42 ProBuilder GSB2 Installation Manual.

All requirements in the installation manual must be met.

Failure to follow all of the requirements may result in property damage, bodily injury,

or even death.

This heater must be installed by a qualified installer who has gone through a training

program for the installation of direct vent gas appliances.

This appliance must be installed in accordance with all local codes, if any; if not,

follow ANSI Z223.1 and NFPA 54(88). In Australia follow AS/NZS 5601.1.

In Manufactured or Mobile Homes must conform with Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard

is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS

A225.1. This appliance may be installed in Manufactured Housing only after the

home is site located.

The fireplace is designed to operate on natural gas, or propane (LP).

All exhaust gases must be vented outside the structure of the living-area.

Combustion air is drawn from outside the living-area structure.

Notify your insurance company before hooking up this fireplace.

Introduction 3

Table of Contents



Introduction ...................................................2

Important Information...................................2

Installation Warnings....................................2

Table of Contents..........................................3

Features .........................................................3

Heating Specifications..................................3

Before You Begin..........................................6

Location of Controls.....................................6

Starting the Fireplace for the First Time.....7

Turning the Fireplace On and Off................7

Adjusting the Flame Height..........................8

Adjusting the Blower Speed (Optional) ......8

Continuous Pilot / GreenSmart™ Pilot

Switch.............................................................9

Starting the Heater for the First Time..........9

Adjusting the Blower Speed (Optional) ......9

Normal Operating Odors..............................9

Power Outages..............................................9

Glass Frame Removal and Installation.....10

Crushed Glass Installation.........................13

Maintaining Your Heater's Appearance....13

Cleaning The Glass.............................................. 15

Cleaning the Fireplace ......................................... 15

Yearly Service Procedure...........................15

Troubleshooting Table...............................16

Replacement Parts List..............................17

Wiring Diagram ...........................................18

Safety Label......................................................19

CONDITIONS & EXCLUSIONS ...................20

IF WARRANTY SERVICE IS NEEDED: ......20

Index.............................................................21

Features

Works During Power Outages

Contemporary Look

Optional Blower for Heat Distribution

Optional Remote Thermostat

Standing Pilot

Standing or Intermittent (GreenSmart) Pilot

Variable-Rate Heat Output

Low Maintenance

Heating Specifications

Natural Gas Propane

Approximate Heating Capacity (in square feet)* Up to 1,250 Up to 1,250

Maximum BTU Input Per Hour 25,000 25,000

* Heating capacity will vary with floor plan, insulation, and outside temperature.

4 Safety Precautions

IF YOU SMELL GAS:

* Do not light any appliance

* Extinguish any open flame

* Do not touch any electrical switch or plug or unplug anything

* Open windows and vacate building

* Call gas supplier from neighbor's house, if not reached, call fire department

This unit must be installed by a qualified installer to prevent the possibility of an explosion.

Your dealer will know the requirements in your area and can inform you of those people

considered qualified. The room heater should be inspected and cleaned before use and at

least annually by a qualified service person. More frequent cleaning may be required due

to excessive lint from carpeting, bedding material, etc.

The instructions in this manual must be strictly adhered to. Do not use makeshift methods

or compromise in the installation. Improper installation will void the warranty and safety

listing.

This heater is either approved for natural gas (NG) or for propane (LP). Burning

the incorrect fuel will void the warranty and safety listing and may cause an

extreme safety hazard. Direct questions about the type of fuel used to your dealer.

Check for a label on the flame adjust knob on the gas control valve (this is the best

place to check). You may also check for a label on the gas control valve body.

Contact your local building

officials to obtain a permit and

information on any installation

restrictions or inspection

requirements in your area.

Notify your insurance company

of this heater as well.

If the flame becomes sooty, dark

orange in color, or extremely tall,

do not operate the heater. Call

your dealer and arrange for

proper servicing.

It is imperative that control

compartments, screens, or

circulating air passageways of

the heater be kept clean and

free of obstructions. These

areas provide the air necessary

for safe operation.

Do not operate the heater if it is

not operating properly in any

fashion or if you are uncertain.

Call your dealer for a full

explanation of your heater and

what to expect.

Do not store or use gasoline or

other flammable liquids in the

vicinity of this heater.

Do not operate if any portion of

the heater was submerged in

water or if any corrosion occurs.

Immediately call a qualified

service technician to inspect the

appliance and to replace any part

of the control system and any

gas control that has been under

water.

Gas





Safety Precautions 5

Do not place clothing or other

flammable items on or near the

heater. Because this heater can

be controlled by a thermostat

there is a possibility of the

heater turning on and igniting

any items placed on or near it.

Light the heater using the built-in

igniter. Do not use matches or

any other external device to light

your heater.

Allow the heater to cool before

carrying out any maintenance or

cleaning.

The viewing glass should be

opened only for conducting

service. Do not operate with

cracked, broken, or removed

glass.

Any safety screen or guard

removed for servicing must be

replaced prior to operating the

heater.

Never remove, replace, modify or

substitute any part of the heater

unless instructions are given in

this manual. All other work must

be done by a trained technician.

Don't modify or replace orifices.

Operate the heater according to

the instructions included in this

manual.

If the main burners do not start

correctly turn the gas off at the

gas control valve and call your

dealer for service.

Instruct everyone in the house

how to shut gas off to the

appliance and at the gas main

shutoff valve. The gas main

shutoff valve is usually next to

the gas meter or propane tank

and requires a wrench to shut off.

This unit is not for use with solid

fuel

Do not place anything inside the

firebox (except the crushed

glass).

If any component becomes

damaged, replace with Travis

Industries components.

Do not throw this manual away.

This manual has important

operating and maintenance

instructions that you will need at

a later time. Always follow the

instructions in this manual.

Children and adults should be

alerted to the hazards of high

surface temperature and should

stay away to avoid burns or

clothing ignition. Young children

should be supervised when they

are in the same room as the

heater.

Travis Industries, Inc. grants

no warranty, implied or stated,

for the installation or

maintenance of your heater,

and assumes no responsibility

of any consequential

damage(s).







This

Manual

6 Operation

Before You Begin

Read this entire manual before you use your new fireplace (especially the section "Safety Precautions" on

pages 4 & 5). Failure to follow the instructions may result in property damage, bodily injury, or even death.

Location of Controls

There is a door on the lower portion of the screen assembly to provide access to the manual controls on the

fireplace. The door is held closed by two magnets. Open the door by gently pulling outward on the upper

portion of the lower trim.

On/Off Switch This control is used to turn the heater on and off.

Gas Control Knob This knob is used to control gas to the heater and for starting the pilot. There are

three positions, ON, OFF, & PILOT. The pointer to the left of the knob indicates

the position this knob is in.

Flame Adjust Knob This knob controls the flame height from low ("LO") to high ("HI"). The pointer

above the knob points to the position this knob is in.

Continuous Pilot --

GreenSmart Pilot This switch controls how the pilot flame works. See the section “Continuous

Pilot / GreenSmart Pilot” for details.

Optional Remote Receiver The receiver is used in conjunction with the optional remote thermostat. It is used

to control the remote and replaces the on/off switch for direct operation.

Optional Blower Dial This knob controls the speed of the internal convection blower that pushes the

heated air into the room.

On/Off Switch

Flame Adjust Knob

Optional Blower Dial

Shutoff Valve

(accessible with

screen removed)

Rotate the Control Door Down to

Access Controls

Battery Tray - or - Optional Remote Receiver

Continuous / Intermittent Pilot Switch

Operation 7

Starting the Fireplace for the First Time

Burn the heater at a high setting with the blower off for an extended period (up to 48 hours). This will cure

the painted surfaces. Fumes from the paint curing and oil burning off the steel will occur. This is normal.

We recommend opening a window to vent the room.

Condensation may appear on the glass each time you start the fireplace - this is normal.

Blue Flames will occur on the fireplace when it first comes on. After fifteen minutes the flames will turn a

more realistic yellow and orange color.

Certain installations use a remote, thermostat, or wall switch to turn the fireplace on and off. If this is the

case, leave the ON/OFF switch "ON".

Verify the power backup and control light batteries are installed.

Turning the Fireplace On and Off

Do not place any combustible items on top of or directly in front of the heater, even temporarily. The

optional thermostat may start the heater causing a combustible item to ignite.

If the heater turns on and off frequently while using the thermostat, you may want to adjust the flame

height down until it produces just enough heat needed.

ON/OFF SWITCH

Use this switch to turn the main

burner on and off manually.

After the pilot has been started...

OPTIONAL REMOTE THERMOSTAT

See the instructions included with the remote

for details on operation.

°F

8 Operation

Adjusting the Flame Height

This fireplace has an adjustable flame to tailor the look and heat output to your specific needs. It is adjusted

by turning the flame adjust knob.

Adjusting the Blower Speed (Optional)

The optional blower helps transfer heat from the heater into the room. It will not turn on until the heater is up to

temperature (approximately 10 minutes after starting). See the illustration below for instructions on adjusting

the blower speed.

HIGH

LOW

FLAME ADJUST

BLOWER

OFF

HIGH

LOW

Operation 9

Continuous Pilot / GreenSmart™ Pilot Switch

This fireplace may run with the pilot continuously running or in GreenSmart (intermittent) mode. For most

homeowners, the GreenSmart mode is preferred (this saves fuel, doesn’t give off un-needed heat). However,

in some situations the homeowner may prefer to switch the fireplace to continuous pilot. The most typical

reasons for switching to continuous pilot are:

Very Cold Conditions – in very cold conditions you may notice that the burner does not light quickly, and

the flames lift off the burner. If this is situation, we recommend you switch to continuous pilot. This will

create a slight draft in the vent, allowing for the burner to light quickly and draft correctly.

Excessive Condensation on Glass After Startup – certain installations may encounter excessive fogging on

the window after startup (not just the first time the fireplace was started). This is an aesthetic condition that

may be remedied by switching the fireplace to continuous pilot.

Cold Glass or Fireplace Front – in very cold conditions you may notice that the fireplace front and glass

become very cold. To remedy this, switch the fireplace to continuous pilot.

Frequent On / Off Operation – if you are frequently turning the fireplace on and off, you may wish to leave

it in continuous pilot. This allows the burner to turn on more quickly, without pilot ignition delay.

Starting the Heater for the First Time

Burn the heater at a low setting with the blower off for an extended period (up to 48 hours). This will cure

the painted surfaces. Fumes from the paint curing and oil burning off the steel will occur. This is normal.

We recommend opening a window to vent the room.

Condensation may appear on the glass each time you start the heater - this is normal.

Blue Flames will occur on the heater when it first comes on. After fifteen minutes the flames will turn a

more realistic yellow and orange color.

Verify the batteries are installed.

Adjusting the Blower Speed (Optional)

The optional blower helps transfer heat from the heater into the room. It will not turn on until the heater is up to

temperature (approximately 10 minutes after starting). See page 8 for details on adjusting the blower speed.

Normal Operating Odors

This appliance has several areas that reach high temperatures. Dust or other particles on these areas may

burn and create an odor. This is normal during start-up. You may notice the smell is more acute if the

appliance was left idle for a long period.

Power Outages

Four AA batteries are used as a power backup for the fireplace in case the household (AC) power goes out. These

batteries must be inserted into battery holder (or remove receiver is using the optional GS thermostatic remote). The

fireplace controller will beep once these batteries start to go dead. Replace batteries before each heating season to insure

proper operation.

CONTINUOUS

PILOT

GREEN SMART

PILOT

10 Maintenance

Glass Frame Removal and Installation

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this

appliance and shall be installed for the protection of children and other at-risk individuals.

If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for

this appliance.

The appliance must be completely cool before removing the glass.

Do not strike or slam the glass.

Warning: Do not operate appliance with the glass front removed, cracked or broken.

Replacement of the glass should be done by a licensed or qualified service person.

Remove the screen-trim assembly by lifting the assembly up slightly and tilting it toward you. The mounting

hooks on the back of the assembly will disengage the fireplace. Set the assembly aside for reinstallation.

NOTE: Opening the access door on the front of the assembly allows for a easy location to get a secure grip on the

assembly for removal

Replacement Barrier Part #

270-01989

Remove the glass frame following the directions below.

Top Corner Bottom Corner

Bottom hook

engages this slot in

bracket

Top hook engages

this slot in bracket

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Travis Industries Kamin im Innenbereich Handbücher

Travis Industries

Travis Industries 36 CF II Bedienungsanleitung

Travis Industries

Travis Industries 564 Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries 564 Bedienungsanleitung

Travis Industries

Travis Industries Maverick Bedienungsanleitung

Travis Industries

Travis Industries 616 GSR2 Insert Bedienungsanleitung

Travis Industries

Travis Industries Pro Builder Linear Bedienungsanleitung

Travis Industries

Travis Industries DaVinci Bedienungsanleitung

Travis Industries

Travis Industries 564 HO Bedienungsanleitung

Travis Industries

Travis Industries 1080 CF Bedienungsanleitung

Travis Industries

Travis Industries 564 TRV 25K Bedienungsanleitung

Travis Industries

Travis Industries Flush Plus Bedienungsanleitung

Travis Industries

Travis Industries Flush Wood Plus Bedienungsanleitung

Travis Industries

Travis Industries DVL GSR2 NB Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries Granite 99600200 Service-Handbuch

Travis Industries

Travis Industries 42 ProBuilder MV Bedienungsanleitung

Travis Industries

Travis Industries 21 TRV GreenSmart Bedienungsanleitung

Travis Industries

Travis Industries Avalon Ashpan Bedienungsanleitung

Travis Industries

Travis Industries 4415 HO ST Bedienungsanleitung

Travis Industries

Travis Industries 1750 Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 21 TRV GreenSmart Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch