Travis Industries 1080 CF Bedienungsanleitung

1080 CF Fireplace

• Operation

• Maintenance

Tested and Listed by

OMNI-Test Laboratories, Inc.

Beaverton, Oregon

Report # 028- -81-5

ANSI Z21.88a-2007

WARNING: If the information in these instructions is not followe exactly, a fire or

explosion may result causing property amage, personal injury or loss of

life.

- Do not store or use gasoline or other flammable vapors an liqui s in the vicinity of this

or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; o not use any phone in your buil ing.

• Imme iately call gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire epartment.

- Installation an service must be performe by a qualifie installer, service agency or

the gas supplier.

This appliance may be installe as an OEM installation in a manufacture (mobile) home an must be

installe in accor ance with the manufacturer’s instructions an the manufacture home construction

an safety stan ar , Title 24 CFR, Part 3280.

This appliance is only for use with the type(s) of gas in icate on the rating plate. A conversion kit is

supplie with the appliance.

Owner's Manual

Mukilteo, WA 98275

2 Intro uction

Introduction

We welcome you as a new owner of a 1080 C gas fireplace. This manual details operation and

maintenance of this fireplace. Please familiarize yourself with the Owner's Manual before

operating your heater and save the manual for future reference.

Important Information

No other 1080 C gas fireplace has the same serial

number as yours. The serial number is on the listing

label that is chained to the gas control valve. This

serial number may be needed in case you require

service.

Model: 1080 C ireplace

Serial Number:

Purchase Date:

Purchased rom:

traviswarranty.com

Or, mail your warranty car to:

Travis Industries House of ire

4800 Harbour Pointe Blvd. SW

Mukilteo, WA 98275

Save Your Bill of Sale.

To receive full warranty coverage, you will

need to show evidence of the date you

purchased your heater. Do not mail your

Bill of Sale to us.

We suggest that you attach your Bill of

Sale to this page so that you will have all

the information you need in one place

should the need for service or information

occur.

Installation Warnings

• Installation requirements are printe in the 1080 CF Installation Manual (part # 100-

01193). All requirements in the installation manual must be met.

• Failure to follow all of the requirements may result in property amage, bo ily injury, or

even eath.

• This heater must be installe by a qualifie installer who has gone through a training

program for the installation of irect vent gas appliances.

• This appliance must be installe in accor ance with all local co es, if any; if not, follow

ANSI Z223.1 an NFPA 54(88).

• In Manufacture or Mobile Homes must conform with Manufacture Home Construction

an Safety Stan ar , Title 24 CFR, Part 3280, or, when such a stan ar is not applicable,

the Stan ar for Manufacture Home Installations, ANSI/NCSBCS A225.1. This appliance

may be installe in Manufacture Housing only after the home is site locate .

• The fireplace is esigne to operate on natural gas, or propane (LP).

• All exhaust gases must be vente outsi e the structure of the living-area. Combustion

air is rawn from outsi e the living-area structure.

• Notify your insurance company before hooking up this fireplace.

• The ceramic firebacks must be installe in this fireplace prior to operation.

Intro uction 3

Table of Contents

Intro uction an Important Information

Introduction.............................................................2

Important Information ...............................................2

Installation Warnings ................................................ 2

eatures.................................................................3

Gas Input Specifications ........................................... 3

Safety Precautions

Safety Precautions...................................................4

Operation

Before You Begin..................................................... 6

Controls..................................................................6

Starting the ireplace for the irst Time.......................8

Adjusting the lame Height........................................8

Continuous Pilot – or Very Cold Conditions................8

Normal Operating Odors............................................8

Power Outages.........................................................8

Maintenance

Yearly Service Procedure.......................................... 9

Glass rame Removal and Installation........................ 10

Log Set Installation .................................................. 11

Wiring Diagram........................................................ 20

Replacement Parts List ............................................ 20

Warranty

Warranty ................................................................ 24

Optional Equipment

Optional Equipment List............................................ 22

In ex

Index...................................................................... 24

Features

• Works During Power Outages

• Standard Remote Control with Thermostat

• Realistic "Wood ire" Look

• Convenient Operating Controls

• Variable-Rate Heat Output

• Low Maintenance

Gas Input Specifications

Natural Gas Propane

Maximum BTU Input Per Hour 36,000 36,000

Minimum BTU Input on Low 20,800 23,500

4 Safety Precautions

IF YOU SMELL GAS:

* Do not light any appliance

* Extinguish any open flame

* Do not touch any electrical switch or plug or unplug anything

* Open win ows an vacate buil ing

* Call gas supplier from neighbor's house, if not reache , call fire epartment

This unit must be installed b

a qualified installer to prevent the possibilit

of an

explosion. Your dealer will know the requirements in your area and can inform you

of those people considered qualified. The room heater should be inspected and

cleaned before use and at least annually by a qualified service person. More

frequent cleaning may be required due to excessive lint from carpeting, bedding

material, etc.

The instructions in this manual must be strictl

adhered to. Do not use makeshift

methods or compromise in the installation. Improper installation will void the

warrant

and safet

listin

CH 4

- or -

83H

This heater is either approved

for natural gas (NG) or for

propane (LP). Burning the

incorrect fuel will void the

warranty and safety listing and

may cause an extreme safety

hazard. Direct questions

about the type of fuel used to

your dealer or installer

Operate the heater accordin

to the instructions included in

this manual.

If the main burners do not start

correctly turn the gas off to the

fireplace and call your dealer

for service.

Contact

our local buildin

officials to obtain a permit and

information on any installation

restrictions or inspection

requirements in your area.

Notify your insurance

company of this heater as

well.

If the flame becomes soot

dark orange in color, or

extremely tall, do not operate

the heater. Call your dealer

and arrange for proper

servicing.

It is imperative that control

compartments, screens, or

circulating air passageways of

the heater be kept clean and

free of obstructions. These

areas provide the air necessary

for safe operation. ?Do not operate the heater if it is

not operating properly in any

fashion or if you are uncertain.

Call your dealer for a full

explanation of your heater and

what to expect.

Gas

Do not store or use

asoline or

other flammable liquids in the

vicinity of this heater.

AAAAA

Do not operate if an

portion of

the heater was submerged in

water or if an

corrosion occurs.

Immediately call a qualified

service technician to inspect

the appliance and to replace

any part of the control system

and any gas control that has

been under water.

Safety Precautions 5

Do not place clothin

or other

flammable items on or near

the heater. Because this

heater can be controlled by a

thermostat there is a possibility

of the heater turning on and

igniting any items placed on

or near it.

ht the heater usin

the built-

in electronic igniter. Do not

use matches or any other

external device to light your

heater.

Allow the heater to cool before

carrying out any maintenance

or cleaning.

The viewin

lass should be

opened only for conducting

service. Do not operate with

cracked, broken, or removed

glass.

safet

screen or

uard

removed for servicing must be

replaced prior to operating the

heater.

Never remove, replace, modify

or substitute any part of the

heater unless instructions are

given in this manual. All other

work must be done by a trained

technician. Don't modify or

replace orifices.

Prior to removing the glass,

shut off gas to the appliance

(or remove the batteries from

the battery box and shut off

electricity to the fireplace).

This prevents any chance of

accidental burner ignition

when accessing the firebox.

This

Manual

Do not throw this manual awa

This manual has important

operating and maintenance

instructions that you will need

at a later time. Always follow

the instructions in this manual.

This unit is not for use with

solid fuel

Do not place an

thin

inside

the firebox (except the

included fiber logs).

If the fiber lo

s become

damaged, replace with Travis

Industries log set.

Instruct ever

one in the house

how to shut gas off to the

appliance and at the gas main

shutoff valve. The gas main

shutoff valve is usually next to

the gas meter or propane tank

and requires a wrench to shut

off.

Children and adults should be

alerted to the hazards of high

surface temperature and

should stay away to avoid

burns or clothing ignition.

Young children should be

supervised when they are in

the same room as the heater.

Travis In ustries, Inc.

rants

no warranty, implie or state ,

for the installation or

maintenance of your heater,

an assumes no

responsibility of any

consequential amage(s).

Operate the heater accordin

to the instructions included in

this manual.

If the main burners do not start

correctly turn the gas off to the

fireplace and call your dealer

for service.

6 Operation

Before You Begin

Read this entire manual before you use your new fireplace (especially the section "Safety

Precautions" on pages 4 & 5). ailure to follow the instructions may result in property damage,

bodily injury, or even death.

Controls

Remote Control

The remote control can turn the fireplace on and off or operate as a thermostat. In addition, it can

turn the flame height up or down.

ON H/L

OFF

Continuous Pilot

MODE

SET

TEMP

°F

Wall Switch

The wall switch can turn the fireplace on and off or turn the flame height up or down.

OFF

Operation 7

The Two Modes of Operation

This fireplace uses both a wall switch and thermostat to control the fireplace.

NOTE: Whichever

component is operated last

controls the fireplace. If

you are using the remote

and you press any button on

the wall switch, the remote

is no longer in control of the

fireplace until a button is

pressed on the remote.

OFF

NOTE: Whichever control is

operated last controls the

fireplace.

ON H/L

OFF

Continuous Pilot

MODE

SET

TEMP

°F

Manual Mo e

In manual mode you can turn the fireplace on and off using either the thermostat or remote.

Simply press the “ON” and “O ” buttons on either the wall switch or remote.

Thermostat Mo e

While in thermostat mode, the remote will

monitor the temperature and turn the fireplace

on and off to meet the desired temperature.

To turn on Thermostat Mo e:

Press the “MODE” button on the remote until

“ROOM” appears on the LCD display.

To turn off Thermostat Mo e:

Press the “MODE” button on the remote until

“ROOM” no longer appears on the LCD

display.

ON H/L

OFF

Continuous Pilot

MODE

SET

TEMP

°F

ROOM

When the remote is in

thermostat mode the

word "ROOM" will

appear on the remote.

A justing the Target Temperature of the Thermostat:

Make sure the remote is in thermostat mode. Hold down the “SET” button until the desired

temperature is displayed ( “SET TEMP” will be displayed on the LCD, indicating that the

thermostat temperature is being set). The thermostat may be set at any temperature between 45°

and 99° . If the desired temperature is missed, simply hold down the button (the temperature

will scroll up to 99° then re-start at 45°).

NOTE: If the fireplace is in thermostat mode, and any button on the wall switch is pressed, the

remote will return to manual mode. Simply press any button on the remote to return control of

the fireplace to the remote.

WARNING: While in thermostat mode the fireplace will turn on and off to meet the temperature

demands of the remote. Do not place any items near the fireplace or conduct service without

removing the batteries and disabling the fireplace.

WARNING: If the remote is set to a high temperature the fireplace may remain on for an extended

period of time. This may be a concern to those using LP (propane).

8 Operation

Starting the Fireplace for the First Time

• Burn the heater at a high setting for an extended period (up to 48 hours). This will cure the

painted surfaces. Fumes from the paint curing and oil burning off the steel will occur. This is

normal. We recommend opening a window to vent the room.

• Con ensation may appear on the glass each time you start the fireplace - this is normal.

• Blue Flames will occur on the fireplace when it first comes on. After fifteen minutes the flames

will turn a more realistic yellow and orange color.

djusting the Flame Height

A justment with the Wall Switch (recommen e )

With the fireplace in manual mode and the fireplace on, click the “HI” or “LO” button until the

desired flame height is achieved.

A justment with the Remote

With the fireplace in manual mode and the fireplace on, click and hold the “ON” button until the

desired flame height is achieved. Each time the “ON” button is held down, the flame height will

toggle between getting taller (“HI” will be displayed on the LCD screen) or getting smaller (“LO”

will be displayed on the LCD screen).

Continuous Pilot – For Very Cold Conditions

This fireplace can be configured to run with an intermittent or continuous (standing) pilot. or

normal conditions we recommend using the intermittent pilot (pilot is on only when the main

burner is on). or extremely cold conditions we recommend using a continuous pilot (pilot is on all

the time). By having the pilot on continuously, a draft is established in the vent, allowing the main

burner to turn on with less air-flow disruption.

Setting the Fireplace to Continuous Pilot

Press and hold down the “O Continuous Pilot” button on the remote for 10 seconds. “PILOT” will

appear on the LCD screen, indicating that the fireplace is configured for a continuous pilot. To

configure the fireplace for an intermittent pilot, press and hold down the “O Continuous Pilot”

button on the remote for 10 seconds until the “PILOT” is no longer visible on the LCD screen.

Normal Operating Odors

This appliance has several areas that reach high temperatures. Dust or other particles on these

areas may burn and create an odor. This is normal during start-up. You may notice the smell is

more acute if the appliance was left idle for a long period.

Power Outages

This fireplace utilizes household power (110 VAC) to power the receiver module and intermittent

pilot system. A separate battery box is included to provide power for the adjustable flame height

and in case of power outages. If you experience a power outage and the unit does not operate,

make sure to replace the AA batteries in the battery box (see “Battery Installation” on page 19).

Child Protection Feature

The remote can be disabled to prevent children from operating the fireplace. This is done by

holding down the “ON H/L” and “MODE” button for 5 seconds until “CP” (Child Protection) appears

on the screen. If any button is pressed on the remote “CP” will appear on the screen indicating the

child protection feature is on. To turn this feature off, hold down the “ON H/L” and “MODE” button

for 5 seconds until “CP” disappears from the screen.

Maintenance 9

Yearly Service Procedure

WARNING: Prior to removing the glass, shut off gas to the

appliance (or remove the batteries from the battery box and shut

off electricity to the fireplace). This prevents any chance of

accidental burner ignition when accessing the firebox.

• ailure to inspect and maintain the fireplace may lead to improper combustion and a potentially dangerous

situation. We recommend the following procedures be done by a qualified technician.

1. Remove the glass frame and log set (NOTE: the logs are very fragile - see page 11). If severely

deteriorated, replace. Check the logs for sooting. A small amount of soot along the bottom of the logs is

normal. If excessive sooting is found, the fireplace will require adjustment. Contact your dealer.

2. Inspect the burner and remove any debris.

• Make sure the burner is not warped, cracked, or damaged.

• Check the firebox and area around the pilot to make sure there is no warping or damage.

• If any problem is found, discontinue use and contact your dealer for service.

3. Replace the log set. Clean and replace the glasss. If the glass is damaged, replace. Make sure the

gasket along the perimeter of the glass contacts the face of the firebox and forms an air-tight seal. If it

does not, re-align or replace the gasket to insure an air-tight seal.

4. Start the burner. The flames should be orange/yellow and not touch the top of the firebox. If the pilot or

main burners do not burn correctly, contact your dealer for service.

5. Remove any debris or vegetation near the vent termination. Contact your dealer if any sooting or

deterioration is found near the vent termination.

10 Maintenance

Glass Frame Removal and Installation

WARNING: Prior to removing the glass, shut off gas to the

appliance (or remove the batteries from the battery box and shut

off electricity to the fireplace). This prevents any chance of

accidental burner ignition when accessing the firebox.

Warning: The appliance must be completely cool before removing the glass.

Warning: Do not strike or slam the glass.

The glass frame is held in

place with four latches.

Use the door latch tool to pull the latch forward

and away from the glass frame.

These tabs insert over posts

on the fireplace and help

guide the glass into place.

REPLACING THE GLASS

Slide the glass into place and secure the four latches.

Lift and remove the glass frame

cover. Four hooks on the sides of

the coverhold it in place.

Andere Handbücher für 1080 CF

Inhaltsverzeichnis

Andere Travis Industries Kamin im Innenbereich Handbücher

Travis Industries

Travis Industries 564 Bedienungsanleitung

Travis Industries

Travis Industries DVS GSR NB Insert Bedienungsanleitung

Travis Industries

Travis Industries Pro Builder42 Linear Bedienungsanleitung

Travis Industries

Travis Industries DVL EF II Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart 864 HO Bedienungsanleitung

Travis Industries

Travis Industries Lopi Pro Builder 72 GSB2 Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart 2 Fireplace 564 SS GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 564 TRV GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 99200149 Bedienungsanleitung

Travis Industries

Travis Industries Fireplace Xtrordinair 864 Deluxe Bedienungsanleitung

Travis Industries

Travis Industries LOPI X Bedienungsanleitung

Travis Industries

Travis Industries 1080 CF Bedienungsanleitung

Travis Industries

Travis Industries 4415 ST GSR2 Bedienungsanleitung

Travis Industries

Travis Industries Freedom Bay Bedienungsanleitung

Travis Industries

Travis Industries 430 GSR2 Bedienungsanleitung

Travis Industries

Travis Industries EmberGlo 616 Bedienungsanleitung

Travis Industries

Travis Industries DVS EF Insert Bedienungsanleitung

Travis Industries

Travis Industries Interior Bedienungsanleitung

Travis Industries

Travis Industries 864 HH Bedienungsanleitung

Travis Industries

Travis Industries 564 HO Bedienungsanleitung

Travis Industries

Travis Industries DVS EF Insert Bedienungsanleitung

Travis Industries

Travis Industries 564 Bedienungsanleitung

Travis Industries

Travis Industries DVS Ember-Fyre 2.1 Log Bedienungsanleitung

Travis Industries

Travis Industries 35 CB Australian Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung