Travis Industries 4415 HO GSR2 Bedienungsanleitung

4415 HO GSR2

Fireplace (Aust)

• Direct Vent Fireplace

• Natural Gas or Propane

• Vent Horizontally or Vertically

• Standard Residential

• Mobile Home Approved

Listed by

AS 4553-2008 GMK 10166

IAPMO-R&T OCEANA

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result

causing property damage, personal injury or loss of life.



DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.



DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE.



DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.



DO NOT MODIFY THIS APPLIANCE.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas supplier.

This appliance may be installed in

an aftermarket permanently

located, manufactured home (USA

only) or mobile home, where not

prohibited by local codes.

This appliance is only for use

with the type(s) of gas indicated

on the rating plate. A conversion

kit is supplied with the appliance.

Installation Manual

Installer: After installation give this manual to the home-

owner and explain operation of this heater.

Dragon Wholesaling Pty. Ltd.

Unit 4, 16 Lexington Drive

Bella Vista NSW

Australia 2153

2 Introduction

Overview

This manual details the installation

requirements for the 4415 HO GSR2 fireplace.

For operating and maintenance instructions,

refer to the 4415 HO GSR2 Owner's Manual

(part # 100-01369).

IAPMO-R&T

OCEANA

Gas Mark

GMKXXXX_XX

4415 GSR2

Vented Gas Fireplace Heater

Tested to the combustion performance and construction requirements of AS 4553-2008 Gas Space Heating

Appliances. This appliance must be installed in accordance with all local codes.

This 4415 GSR2 appliance is equipped from the factory only for use with Natural Gas and is only for use

with the type of gas indicated on the rating plate. For conversion to LP (Propane) use a certified kit

supplied by the manufacturer. See owner’s manual for information on making these changes.

This appliance may be installed in an aftermarket, permanently located, manufactured (mobile) home where

not prohibited by local codes.

This vented gas fireplace heater is not for use with air filters. This appliance must be properly connected to

a venting system in accordance with the manufacturer’s installation instructions. Use only approved

coaxial direct vent systems to vent this appliance to the exterior. See owner’s manual for approved brands

of venting.

WARNING:

Improper installation, adjustment, alteration, service or maintenance can cause injury or

property damage. Refer to the owner’s information manual provided with this appliance. For assistance or

additional information consult a qualified installer, service agency or the gas supplier.

This appliance is a Vented Gas Fireplace Heater. Not for use with Solid Fuel.

Young children should be carefully supervised at all times when they are in the same room

as the appliance.

Fireplace to adjacent wall

Wood floor beneath fireplace

Back to enclosure

77 mm

0 mm

4 mm

Base of fireplace to enclosure top

Sides to enclosure

Base of fireplace to a mantel

1524 mm

17 mm

See Owner’s Manual

Minimum Clearances to Combustibles

FAN TYPE VENTED CIRCULATOR

Blower Electrical Rating: 240V., 0.6 Amps, 50 Hz, 76 Watts

Minimum Inlet Pressure (kPa)

Maximum Inlet Pressure (kPa)

Manifold Pressure on “HI” (kPa)

L.P.

2.74

3.24

2.74

N.G.

1.37

1.74

.95

Input Rate on “HI” (MJ/h)

Input Rate on “LO” (MJ/h)

Orifice Size (DMS)

L.P.

44.31

22.6

#49

N.G.

44.31

22.87

#31

This appliance is equipped for installation 0-610 m. For altitudes above 600m, the vent configuration, orifice, or

combination of both may need to be changed. See owner’s manual for information on making these changes.

2014

2015

2013

Feb.

Mar.

Jan.

May

Jun.

Apr.

Aug.

Sep.

Jul.

Nov.

Dec.

Oct.

MANUFACTURE DATE:

4800 Harbour Pointe Blvd. SW

Mukilteo, WA 98275

Manufactured by: Certificate Holder:

www.lopi.com.au

Dragon Wholesaling Pty. Ltd.

Unit 4, 16 Lexington Drive

Bella Vista NSW 2153

Australia

1075

Table of Contents 3

Overview ................................................................... 2

Installation Options.................................................. 6

Heating Specifications............................................. 6

Dimensions............................................................... 6

Packing List .............................................................. 7

Additional Items Required....................................... 7

Recommended Installation Procedure................... 7

Fireplace Placement Requirements ....................... 8

Clearances ......................................................................8

Raised Fireplaces............................................................8

Televisions Placed Above the Fireplace................ 9

Using a Mantel Between the Fireplace and Television....9

Using a Recessed Fireplace Below a Television.............10

Using a Recessed Fireplace with a Recessed

Television ........................................................................11

Minimum Framing Dimensions............................... 12

Nailing Brackets – Extended (Tile Over) Install ....13

Nailing Brackets – Flush Install.............................. 14

Corner Installations.................................................. 15

Removing the Front Panel....................................... 16

Gas Line Requirements........................................... 17

Fuel .................................................................................17

Gas Line Connection.......................................................17

Gas Inlet Pressure...........................................................17

Directions for Connecting a Gas Pressure Test Gauge...17

Gas Line Location............................................................18

Relocating the Gas Line to the Baseplate ......................18

Electrical Connection............................................... 19

Relocating the Electrical Line to the Baseplate ..............19

Vent Requirements................................................... 20

Vent Clearances..............................................................20

Vent Firestop...................................................................20

Altitude Considerations....................................................20

Approved Vent.................................................................20

Vent Installation...............................................................20

Vertical Pipe Shield .........................................................21

Minimum Vent Pipe Shield – Used for Minimum Vent

Applications Only.............................................................22

Approved Vent Configurations............................... 23

Restrictor Position ...........................................................23

Exhaust Restrictor...........................................................23

Intake Restrictor ..............................................................24

Diffuser............................................................................25

Minimum Vent Configuration.................................. 26

Vent Configuration: Vertical Termination.............. 27

Vent Configuration: Horizontal Termination

with Vertical Rise...................................................... 28

Vent Configuration: Horizontal Termination

with Vertical Rise – 8” Vent..................................... 29

Termination Requirements...................................... 30

Hearth Requirements............................................... 31

Drywall Supports......................................................31

Facing Requirements – Flush Install......................32

Facing Requirements – Extended (Tile Over)

Install .........................................................................33

Do Not Drill or Screw Zone..............................................34

Mantel Requirements...............................................35

Mantel Column Clearances...........................................35

Steps for Finalizing the Installation........................36

Air Shutter Adjustment ....................................................37

Glass Frame Removal and Installation ..................38

Fireback Installation.................................................40

Crushed Glass Installation......................................42

LP Conversion Instructions ....................................43

Wiring Diagram.........................................................47

Power Heat Duct Installation...................................48

4 Safety Precautions

Safety Warnings

Failure to follow all of the requirements may result in property damage, bodily injury, or even death.

This unit must be installed by a qualified installer to prevent the possibility of an explosion.

This appliance must be installed in accordance with all local codes, if any; if not, in U.S.A. follow ANSI

Z223.1 and NFPA 54(88), in Canada follow CSA B149.1.

A manufactured home (USA only) or mobile home OEM installation must conform with the

Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a

standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS

A225.1, or Standard for Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4. This

appliance may be installed in Manufactured Housing only after the home is site located.

All exhaust gases must be vented outside the structure of the living-area. Combustion air is drawn

from outside the living-area structure. The venting must not be connected to a chimney flue serving a

separate solid-fuel burning appliance.

Notify your insurance company before hooking up this fireplace.

The room heater should be inspected before use and at least annually by a qualified service person.

More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc.

The instructions in this manual must be strictly adhered to. Do not use makeshift methods or

compromise in the installation. Improper installation will void the warranty and safety listing.

This heater is approved for use with natural gas (NG) or propane (LP). Burning the incorrect fuel will

void the warranty and safety listing and may cause an extreme safety hazard. Direct questions about

the type of fuel used to your dealer.

Contact your local building officials to obtain a permit and information on any installation restrictions

or inspection requirements in your area.

If the flame becomes sooty, dark orange in color, or extremely tall, do not operate the heater. Call

your dealer and arrange for proper servicing.

It is imperative that control compartments, screens, or circulating air passageways of the heater be

kept clean and free of obstructions. These areas provide the air necessary for safe operation.

Do not operate the heater if it is not operating properly in any fashion or if you are uncertain. Call

your dealer for a full explanation of your heater and what to expect.

Do not store or use gasoline or other flammable liquids in the vicinity of this heater.

Do not operate if any portion of the heater was submerged in water or if any corrosion occurs.

Immediately call a qualified service technician to inspect the appliance and to replace any part of the

control system and any gas control which has been under water.

Do not place clothing or other flammable items on or near the heater. Because this heater can be

controlled by a thermostat there is a possibility of the heater turning on and igniting any items placed

on or near it.

Light the heater using the built-in igniter. Do not use matches or any other external device to light

your heater.

Never remove, replace, modify or substitute any part of the heater unless instructions are given in this

manual. All other work must be done by a trained technician. Don't modify or replace orifices.

The viewing glass should be opened only for conducting service.

Any safety screen or guard removed for servicing must be replaced prior to operating the heater.

Safety Precautions 5

Safety Warnings (continued)

Allow the heater to cool before carrying out any maintenance or cleaning.

Operate the heater according to the instructions included in this manual.

If the main burners do not start correctly turn the gas off and call your dealer for service.

This unit is not for use with solid fuel.

Do not place anything inside the firebox (except approved Travis Industries components).

Warning: Do not operate appliance with the glass front removed, cracked or broken. Replacement

of the glass should be done by a licensed or qualified service person.

Do not throw this manual away. This manual has important operating and maintenance instructions

that you will need at a later time. Always follow the instructions in this manual.

Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical

barrier is recommended if there are at risk individuals in the house. To restrict access to a fireplace

or stove, install an adjustable safety gate to keep toddlers, young children and other at risk individuals

out of the room and away from hot surfaces.

Children and adults should be alerted to the hazards of high surface temperature and should stay

away to avoid burns or clothing ignition. Do not touch the hot surfaces of the heater. Educate all

children of the danger of a high-temperature heater.

Due to the high temperature, the heater should be located out of traffic and away from furniture and

draperies.

Instruct everyone in the house how to shut gas off to the appliance and at the gas main shutoff valve.

The gas main shutoff valve is usually next to the gas meter or propane tank and requires a wrench to

shut off.

Travis Industries, Inc. grants no warranty, implied or stated, for the installation or

maintenance of your heater, and assumes no responsibility of any consequential damage(s).

SAFETY WARNINGS:

DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.

DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE.

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN

OPERATION.

DO NOT MODIFY THIS APPLIANCE.

THIS INSTALLATION MUST CONFORM WITH THE FOLLOWING:

Manufacturer’s Installation instructions

Local Gas Fitting Regulations

Municipal Building Codes,

Refer to AS/NZS 5601.1 for Gas Installations.

S.A.A. Wiring Code

Local Electrical Regulations

Any other statutory regulations

NOT SUITABLE FOR MARINE USE.

NOT INTENDED FOR FIREPLACE INSERT.

APPLIANCES INCORPORATING A LIVE FUEL EFFECT, AND DESIGNED TO

OPERATE WITH LUMINOUS FLAMES, MAY EXHIBIT SLIGHT CARBON

DEPOSITION.

6 Features and Specifications

Installation Options

Residential or Mobile Home

Straight or Corner Placement

Raised or Floor Placement

Internal or External Chase

Bedroom Approved

Heating Specifications

Natural Gas Propane

Approximate Heating Capacity (in square meters)* Up to 195 Up to 195

Maximum BTU Input Per Hour (MJ/H) 44.31 44.31

* Heating capacity will vary with floor plan, insulation, and outside temperature.

Dimensions

Left

a' gauche

Front

avant

Right

droit

Rear

arrie're

48-3/4" *

1239mm *

16-1/2" *

420mm *

60"

1524mm

37-3/8"

924mm

25mm

1/2"

12mm

* Includes the requisite clearance to framing (1/8"

4mm to rear, 5/8" 16mm to the sides)

10-3/8"

264mm

15-3/4"

401mm

11-1/4"

286mm

7-5/8"

194mm

34-3/4"

883mm

1150mm

45-1/4"

255 lbs.

115 Kg.

Installation (for qualified installers only) 7

Packing List

Propane Conversion Kit

Remote Control

4 AA Batteries, 3 AAA Batteries

Glass Latch Tool

(2) Firestops (8” Diameter)

Top Drywall Support

Heat Shield

Additional Items Required

If using LP (propane) a conversion kit is required (sku 94400999 – GSR Stepper Motor Kit).

Gas Line Equipment (shutoff valve, pipe, etc.)

Electrical Equipment (min. 14 gauge, grounded line)

This Fireplace Requires Firebacks and 7 lbs. of 1/4” Crushed Glass

Firebacks 96100971 Stainless Steel

96100972 Black Enamel

96100973 Black Painted

96100974 Ledgestone

Crushed Glass 94500580 Platinum (10 lbs.)

94500581 Bronze (10 lbs.)

94500582 Cobalt (10 lbs.)

Recommended Installation Procedure

Frame the opening for the fireplace. Make sure to allow for vent installation.

This fireplace is designed to accommodate 1/2" (13mm) drywall (see "Nailing Brackets" on page 12 for

details). Secure the fireplace to the framing.

Install the vent, gas line and electrical hook-up.

Install the drywall.

Install the hearth (if applicable).

Install the facing (if applicable).

Install the mantel (if applicable).

Finalize the installation (see page 35).

8 Installation (for qualified installers only)

Fireplace Placement Requirements

Fireplace must be installed on a level surface capable of supporting the fireplace and vent

Fireplace must be placed directly on wood or non-combustible surface (not on linoleum or carpet)

Fireplace should be located out of traffic and away from furniture and draperies.

Fireplace must be placed so the gaps below and above the glass frame do not become blocked.

Fireplace may be placed in a bedroom. Please be aware of the large amount of heat this appliance produces

when determining a location.

Clearances

(a) Clearance to Side of Fireplace 5/8” (16mm). Do not place insulation in this space.

NOTE: Drywall or other combustible may contact the side of the fireplace in front of the framing. The

material must not protrude in front of the fireplace and may be a maximum ½” (13mm) thick.

(b) Clearance to Back of Fireplace 1/8” (4mm). Do not place insulation in this space.

Raised Fireplaces

The fireplace (and hearth, if desired) may be placed on a platform designed to support the fireplace and vent.

The base of the fireplace must be a minimum 60” below the room ceiling.

The firebox opening is approximately 10.375” (264mm) above the base of the fireplace. For a

typical raised fireplace of 36” (915mm), place the fireplace on a platform 25.625” (651mm) tall.





Installation (for qualified installers only) 9

Televisions Placed Above the Fireplace

The following section details three methods to allow for television installation above the fireplace.

Using a Mantel Between the Fireplace and Television

IMPORTANT NOTE REGARDING TELEVISIONS AND THIS FIREPLACE

Most television manufacturers instruct the homeowner to not place the television above a heat source. Doing so may

negatively affect the longevity of the television and may negate the warranty. If you do place a television above the fireplace,

please be aware of the large amount of heat generated by the fireplace and consider placing the television above a mantel to

reduce the amount of heat that reaches the television. The homeowner must understand that Travis Industries does not take

responsibility for any negative impact to televisions placed near this fireplace.

Minimum Dimensions:

(a) Mantel Height above Base of Fireplace

Mantel must fall within shaded portion of the chart above. 42” (1067mm) with 8” (203mm) mantel depth

See chart above if using a larger mantel.

(b) Mantel Depth* Minimum 8” (203mm)

* NOTE: The minimum mantel depth is 8”. This allows heat to travel forward and dissipate.

EXAMPLES: If you have a TV that is greater than 6” deep (including the 1” gap behind), you will need to alter the mantel

depth and height. If your TV is 9” deep (including the 1” gap behind), the mantel should be 11” (this provides the necessary 2”

recess for the TV). The 11” mantel would require a 43.5” (292mm) mantel height (see chart above).

WIRING NOTE: If running wiring into the enclosure, use thermal insulating wrap around the wiring. Secure the wiring to

protect from contact with hot surfaces.

Fireplace

Min. 2" (51mm)

From Front of TV

Mantel Must be

Min. 1" (26mm) Thick

Min. 1" (26mm) Air Gap Behind TV

(typically provided by wall mount)

Min. 1" (26mm)

Television (TV)

(b) Depth

(a)

Height

Above

Base of

Fireplace

46" (1169mm)

0" (0mm)

1" (25mm)

2" (51mm)

8" (203mm)

7" (178mm)

6" (152mm)

5" (127mm)

4" (102mm)

3" (76mm)

9" (229mm)

10" (254mm)

11" (279mm)

12" (305mm)

45" (1143mm)

44" (1118mm)

43" (1093mm)

42" (1067mm)

41" (1042mm)

47" (1194mm)

10 Installation (for qualified installers only)

Using a Recessed Fireplace Below a Television

IMPORTANT NOTE REGARDING TELEVISIONS AND THIS FIREPLACE

Most television manufacturers instruct the homeowner to not place the television above a heat source. Doing so may

negatively affect the longevity of the television and may negate the warranty. If you do place a television above the fireplace,

please be aware of the large amount of heat generated by the fireplace and consider placing the television above a mantel to

reduce the amount of heat that reaches the television. The homeowner must understand that Travis Industries does not take

responsibility for any negative impact to televisions placed near this fireplace.

Minimum Dimensions:

(a) Fireplace Recess Height above Base of Fireplace

Recess must fall within shaded portion of the chart above. 42” (1067mm) with 8” (203mm) recess depth

See chart above if using a larger recess.

(b) Fireplace Recess Depth plus Mantel Depth* Minimum 8” (203mm)

* NOTE: The minimum recess plus mantel depth is 8”. This allows heat to travel forward and dissipate.

EXAMPLES: If you have a TV that is 3” deep (including the 1” gap behind), you will need to put in a 5” mantel (the 2” is

measured from the front of the TV). The fireplace can then be recessed 3” into the wall to allow for the 8” of recess plus

mantel depth.

WIRING NOTE: If running wiring into the enclosure, use thermal insulating wrap around the wiring. Secure the wiring to

protect from contact with hot surfaces.

Fireplace

Min. 1" (26mm) Air Gap Behind TV

(typically provided by wall mount)

Television (TV)

Min. 6"

(152mm)

Min. 2" (51mm)

From Front of TV Min. 1" (26mm)

Min. 6"

(152mm)

(b) Depth

(a)

Height

Above

Base of

Fireplace

46" (1169mm)

0" (0mm)

1" (25mm)

2" (51mm)

8" (203mm)

7" (178mm)

6" (152mm)

5" (127mm)

4" (102mm)

3" (76mm)

9" (229mm)

10" (254mm)

11" (279mm)

12" (305mm)

45" (1143mm)

44" (1118mm)

43" (1093mm)

42" (1067mm)

41" (1042mm)

47" (1194mm)

Andere Handbücher für 4415 HO GSR2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Travis Industries Kamin im Innenbereich Handbücher

Travis Industries

Travis Industries 564 Bedienungsanleitung

Travis Industries

Travis Industries DVS FIREPLACE Bedienungsanleitung

Travis Industries

Travis Industries Fireplace Xtrordinair 864 GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 35 CB Australian Bedienungsanleitung

Travis Industries

Travis Industries Fireplace Xtrordinair 864 Deluxe Bedienungsanleitung

Travis Industries

Travis Industries Revolution 36CF Bedienungsanleitung

Travis Industries

Travis Industries 864 See Through Bedienungsanleitung

Travis Industries

Travis Industries 21 DV RV Bedienungsanleitung

Travis Industries

Travis Industries Shadowbox Black Bedienungsanleitung

Travis Industries

Travis Industries ProBuilder 54 Linear Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Bedienungsanleitung

Travis Industries

Travis Industries DVS GSR2 NB Insert Bedienungsanleitung

Travis Industries

Travis Industries 864 HO GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 1080 CF Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV GSR2 Bedienungsanleitung

Travis Industries

Travis Industries Avalon Rosario Winthrop 864 Bedienungsanleitung

Travis Industries

Travis Industries 864 HO NB GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 864 HH Bedienungsanleitung

Travis Industries

Travis Industries 31 DVI Bedienungsanleitung

Travis Industries

Travis Industries Revere Fireplace Insert Bedienungsanleitung

Travis Industries

Travis Industries 36 CF II Bedienungsanleitung

Travis Industries

Travis Industries DVL EF Insert Bedienungsanleitung

Travis Industries

Travis Industries 6015 HO GSR2 Bedienungsanleitung

Travis Industries

Travis Industries DVL EF II Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch