Travis Industries Fireplace Xtrordinair 864 GSR2 Bedienungsanleitung

864 GSR2

With Ember-Glo™ Lights

Owner’s Manual

40K, 40K CF, 31K, 31K CF

WARNING:

If the information in these instructions is not followed exactly, a fire or explosion may result

causing property damage, personal injury or loss of life.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas supplier.

HOT GLASS WILL CAUSE

BURNS

DO NOT TOUCH GLASS

UNTIL COOLED

NEVER ALLOW CHILDREN

TO TOUCH GLASS

A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance

and shall be installed for the protection of children

and other at-risk individuals.

Tested and Listed by

Report # 0028GF059S

ANSI Z21.88-2016

CSA 2.33-2016

 Built-In Direct Vent

Fireplace

 Natural Gas or Propane

 Residential or Mobile

Home

This appliance may be installed in an aftermarket, permanently located, manufactured home

(USA only) or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. A conversion

kit is supplied with the appliance.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

French language manuals at travisindustries.com

Manuels de langue Française à travisindustries.com

Travis Industries, Inc. 12521 Harbour Reach Dr., Mukilteo, WA 98275 www.travisproducts.com

2 Introduction

Introduction

We welcome you as a new owner of a 864 GSR2 gas fireplace. This manual details operation and

maintenance of this fireplace. Please familiarize yourself with the Owner's Manual before operating your

heater and save the manual for future reference.

Important Information

No other 864 GSR2 gas fireplace has the same serial

number as yours. The serial number is on the listing

label that is chained to the gas control valve. This

serial number may be needed in case you require

service.

Model: 864 GSR2 Fireplace

Serial Number:

Purchase Date:

Purchased From:

traviswarranty.com

Save Your Bill of Sale.

To receive full warranty coverage, you will

need to show evidence of the date you

purchased your heater.

We suggest that you attach your Bill of Sale

to this page so that you will have all the

information you need in one place should the

need for service or information occur.

Installation Warnings

 Installation requirements are printed in the 864 GSR2 Installation Manual. All

requirements in the installation manual must be met.

 Failure to follow all of the requirements may result in property damage, bodily injury,

or even death.

 This heater must be installed by a qualified installer who has gone through a training

program for the installation of direct vent gas appliances.

 This appliance must be installed in accordance with all local codes, if any; if not,

follow ANSI Z223.1 and NFPA 54(88). In Australia follow AS/NZS 5601.1.

 In Manufactured or Mobile Homes must conform with Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard

is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS

A225.1. This appliance may be installed in Manufactured Housing only after the

home is site located.

 The fireplace is designed to operate on natural gas, or propane (LP).

 All exhaust gases must be vented outside the structure of the living-area.

Combustion air is drawn from outside the living-area structure.

 Notify your insurance company before hooking up this fireplace.

Introduction 3

Table of Contents



Introduction ................................................... 2

Important Information ................................... 2

Installation Warnings .................................... 2

Table of Contents .......................................... 3

Features ......................................................... 3

Heating Specifications .................................. 3

Before You Begin .......................................... 6

Remote Control Warnings ........................................ 6

Remote Set-Up ............................................... 7

Verify the Switch is on “REMOTE” ...................... 7

Synchronize the Transmitter to the IFC ............... 7

Location of Controls ..................................... 8

Direct Operation ............................................ 8

Starting the Fireplace for the First Time ..... 9

Intermittent/Continuous Pilot ....................... 9

Switching from Intermittent (IPI) to Continuous

Pilot (CPI) ............................................................ 9

Remote Operation ....................................... 10

Display Overview .............................................. 1 0 

Listen for the “Beep” .......................................... 10

Manual On-Off / Smart Thermostat /

Standard Thermostat .................................. 11

Mode Controls (Flame, Blower, Light,

Comfort Control, EmberBed Light) ........... 12

Mode Controls - continued ......................... 13

Accent Light ............................................................ 13

Comfort Control (rear burner) ................................. 13

EmberBed Light (AUX) ........................................... 13

Display Fahrenheit or Celsius .................... 13

Low Battery Indicator ................................. 14

Transmitter Batteries ......................................... 1 4 

IFC Batteries ..................................................... 14

Battery Replacement .................................. 14

Battery Installation ............................................. 14

Transmitter Battery Installation .......................... 14

Power Outages ............................................ 14

Child-Proof Feature .................................... 15

Normal Operating Sounds ......................... 15

Normal Operating Odors ............................ 15

Maintaining Your Fireplace's Appearance . 16

Yearly Service Procedure ........................... 16

Grill Installation and Removal ................... 17

Face Installation and Removal .................. 18

Barrier Removal .......................................... 19

Glass Frame Removal and Installation ..... 20

Glass Frame Removal and Installation

(continued) ................................................... 21

Glass Cleaning ............................................ 22

Accent Light Bulb Replacement ................ 22

Ember Light Bulb Replacement ................ 23

Classic Log Set Installation (94500721) .... 24

Wiring Diagram ........................................... 32

Replacement Parts List .............................. 32

CONDITIONS & EXCLUSIONS ................... 33

IF WARRANTY SERVICE IS NEEDED: ...... 33

Features

 Works During Power Outages (battery backup)

 GreenSmart™ 2 Thermostat / Remote Control

 Realistic "Wood Fire" Look

 Included Blower for Effective Heat Distribution

 Built-In Accent Light (night light)t

 EmberBed Light

 Standing or Intermittent (GreenSmart) Pilot

 Convenient Operating Controls

 Variable-Rate Heat Output

 Low Maintenance

Heating Specifications

Natural Gas Propane

31K 864 Approximate Heating Capacity (in square feet)* Up to 1,400 Up to 1,400

Maximum BTU Input Per Hour 31,000 31,000

40K 864 Approximate Heating Capacity (in square feet)* Up to 2,000 Up to 2,000

Maximum BTU Input Per Hour 40,000 40,000

* Heating capacity will vary with floor plan, insulation, and outside temperature.

4 Safety Precautions

IF YOU SMELL GAS:

* Do not light any appliance

* Extinguish any open flame

* Do not touch any electrical switch or plug or unplug anything

* Open windows and vacate building

* Call gas supplier from neighbor's house, if not reached, call fire department

This unit must be installed by a qualified installer to prevent the possibility of an explosion.

Your dealer will know the requirements in your area and can inform you of those people

considered qualified. The room heater should be inspected and cleaned before use and at

least annually by a qualified service person. More frequent cleaning may be required due

to excessive lint from carpeting, bedding material, etc.

The instructions in this manual must be strictly adhered to. Do not use makeshift methods

or compromise in the installation. Improper installation will void the warranty and safety

listing.

This heater is either approved for natural gas (NG) or for propane (LP). Burning

the incorrect fuel will void the warranty and safety listing and may cause an

extreme safety hazard. Direct questions about the type of fuel used to your dealer.

Check for a label on the flame adjust knob on the gas control valve (this is the best

place to check). You may also check for a label on the gas control valve body.

Contact your local building

officials to obtain a permit and

information on any installation

restrictions or inspection

requirements in your area.

Notify your insurance company

of this heater as well.

If the flame becomes sooty, dark

orange in color, or extremely tall,

do not operate the heater. Call

your dealer and arrange for

proper servicing.

It is imperative that control

compartments, screens, or

circulating air passageways of

the heater be kept clean and

free of obstructions. These

areas provide the air necessary

for safe operation.

Do not operate the heater if it is

not operating properly in any

fashion or if you are uncertain.

Call your dealer for a full

explanation of your heater and

what to expect.

Do not store or use gasoline or

other flammable liquids in the

vicinity of this heater.

Do not operate if any portion of

the heater was submerged in

water or if any corrosion occurs.

Immediately call a qualified

service technician to inspect the

appliance and to replace any part

of the control system and any

gas control that has been under

water.

Gas





Safety Precautions 5

Do not place clothing or other

flammable items on or near the

heater. Because this heater can

be controlled by a thermostat

there is a possibility of the

heater turning on and igniting

any items placed on or near it.

Light the heater using the built-in

igniter. Do not use matches or

any other external device to light

your heater.

Allow the heater to cool before

carrying out any maintenance or

cleaning.

The viewing glass should be

opened only for conducting

service. Do not operate with

cracked, broken, or removed

glass.

Any safety screen or guard

removed for servicing must be

replaced prior to operating the

heater.

Never remove, replace, modify or

substitute any part of the heater

unless instructions are given in

this manual. All other work must

be done by a trained technician.

Don't modify or replace orifices.

Operate the heater according to

the instructions included in this

manual.

If the main burners do not start

correctly turn the gas off at the

gas control valve and call your

dealer for service.

Instruct everyone in the house

how to shut gas off to the

appliance and at the gas main

shutoff valve. The gas main

shutoff valve is usually next to

the gas meter or propane tank

and requires a wrench to shut off.

This unit is not for use with solid

fuel

Do not place anything inside the

firebox (except the included fiber

logs).

If the fiber logs become

damaged, replace with Travis

Industries media.

Do not throw this manual away.

This manual has important

operating and maintenance

instructions that you will need at

a later time. Always follow the

instructions in this manual.

Children and adults should be

alerted to the hazards of high

surface temperature and should

stay away to avoid burns or

clothing ignition. Young children

should be supervised when they

are in the same room as the

heater.

Travis Industries, Inc. grants

no warranty, implied or stated,

for the installation or

maintenance of your heater,

and assumes no responsibility

of any consequential

damage(s).







This

Manual

6 Operation

Before You Begin

 Read this entire manual before you use your new heater (especially the section "Safety Precautions"

on pages 4 & 5). Failure to follow the instructions may result in property damage, bodily injury, or

even death.

Remote Control Warnings

KEEP BATTERIES AND COVER INSTALLED AT ALL TIMES

The remote control system requires the batteries and battery cover to

remain in place at all times. Once the batteries or cover are removed, the

system may re-start in standing pilot mode. If this occurs when the heater is

in Remote Mode, you will not be able to turn the heater off manually from

the battery box.

If you need to replace dead batteries, make sure to turn the appliance

off before removing the batteries.

NOTE: If the batteries go dead, the system will operate normally as long

as household power (120v AC) is present.

The transmitter and IFC are radio frequency devices. Placing the transmitter in or near metal may

severely reduce the signal range.

Turn off the main gas supply to the appliance during installation or maintenance. In case of remote

control malfunction turn off the main gas supply to the appliance.

PROGRAMMING THE REMOTE

The SIT GSR2 remote may be programmed to disable the thermostat or any of the modes (flame height, blower, light,

comfort control, Standing Pilot *, or auxiliary power input). This allows you to tailor the remote to the appliance.

* We do not recommend disabling the standing pilot option for our gas appliances. This feature may be recommended

for cold regions or installations with sub-optimal venting.

How to Disable/Enable the Thermostat

The remote is shipped with the thermostat enabled.

1 Remove one battery from the remote.

2 Press and hold the thermostat button while

replacing the battery. This will toggle the

thermostat function. Repeat this process to toggle

the thermostat function to the desired setting.

How to Disable/Enable Modes (Light, Blower, etc.)

The remote is shipped with all modes enabled (except AUXiliary).

1 Remove one battery from the remote.

2 Press and hold the on/off button and mode button while replacing the battery.

Keep the on/off button depressed during the following steps.

3 While keeping the on/off button depressed, press

and release the mode button until the mode that

needs to be changed is illuminated.

4 With the desired mode illuminated (see illustration

to the right), press the “up” or “down” button to

activate or clear the mode being addressed.

Make sure to keep the on/off button depressed

during this process.

5 Release the on/off button to complete

programming.

°F

AAA Battery

"CLR" = thermostat

function disabled.

"SET" = thermostat

function enabled.

°F

AAA Battery

Flame

Height

Optional

Blower

Comfort

Control

Accent

Light

AUX

Standing

Pilot

"SET" = selected

mode enabled.

"CLR" = selected

mode disabled.

Operation 7

Remote Set-Up

Verify the Switch is on “REMOTE”

The battery holder has a switch built into it (see Figure 1). This switch must remain in the REMOTE

position for the remote to operate.

Figure 1

Synchronize the Transmitter to the IFC

The transmitter will need to be synchronized to the IFC (Integrated Fireplace Control) before the remote

will work correctly. Synchronizing is done in the following two steps below (see Figure 2):

1. Press the PRG (Program) button on the battery box (IFC will beep 3 times).

2. Press the “ON” button on the transmitter (IFC will beep 3 times).

Figure 2

NOTE: If power is cut off to the IFC for an extended period of time, you may need to re-synchronize the

remote.

Clearing the System Memory

This appliance uses an Integrated Fireplace Control (IFC) to store the unique code for the

remote control. If you wish to clear the system memory, MAKE SURE GAS IS TURNED OFF

TO THE APPLIANCE then press the PRG (Program) button for 10 seconds. The pilot will start

to spark repeatedly, signifying all system memory has been cleared. The system will return to its

original configuration: a remote will need to be synchronized; and, the system will operate under

continuous pilot mode.

ON REMOTE OFF

°F

"Beep"

8 Operation

Location of Controls

Direct Operation

The fireplace may be directly operated from the battery holder. The three positions are shown below:

ON – Burner turns on (regardless of transmitter settings).

OFF – Burner turns off (regardless of transmitter settings).

REMOTE – Burner is controlled by the transmitter.

NOTE: When the battery holder switch is turned to ON or OFF, the mode settings (Flame Height, Comfort

Control) will remain in the same state as before the switch was moved (i.e.: the IFC “remembers” the last

setting). If you wish to adjust the mode settings use the transmitter mode button to adjust the settings

(see “Mode Controls” on page 12). The thermostat and burner on/off operating functions will not work on

the transmitter.

ON REMOTE OFF

Some fireplaces

use a removable

cover. Remove it

to access the

controls.

Some fireplaces use an

access door (grill) and

concealment cover. Open

them to expose the

controls.

An instruction card for

operating the fireplace is

attached to the inside of

the fireplace here.

Replace it for easy

reference.

The battery holder / switch is on the

right side, below the firebox.

Most features will be controlled by the

included remote.

°F

Use the rheostat on the fireplace to

control the EmberBed brightness.

EM BERBED LIGHT

ON REMOTE OFF

Operation 9

Starting the Fireplace for the First Time

 Burn the heater at a high setting with the blower off for an extended period (up to 48 hours). This will

cure the painted surfaces. Fumes from the paint curing and oil burning off the steel will occur. This

is normal. We recommend opening a window to vent the room.

 Condensation may appear on the glass each time you start the fireplace - this is normal.

 Blue Flames will occur on the fireplace when it first comes on. After fifteen minutes the flames will

turn a more realistic yellow and orange color.

 Verify the power backup batteries are installed (see page 14).

Intermittent/Continuous Pilot

This heater may run with the pilot continuously running or in intermittent mode. For most homeowners,

the intermittent mode is preferred (this saves fuel, doesn’t give off un-needed heat). However, in some

situations the homeowner may prefer to switch the heater to continuous pilot. The most typical reasons

for switching to continuous pilot are:

 Very Cold Conditions – in very cold conditions you may notice that the burner does not light quickly,

and the flames lift off the burner. If this is situation, we recommend you switch to continuous pilot.

This will create a slight draft in the vent, allowing for the burner to light quickly and draft correctly.

 Excessive Condensation on Glass After Startup – certain installations may encounter excessive

fogging on the window after startup (not just the first time the heater was started). This is an aesthetic

condition that may be remedied by switching the heater to continuous pilot.

 Cold Glass or Heater Front – in very cold conditions you may notice that the heater front and glass

become very cold. To remedy this, switch the heater to continuous pilot.

 Frequent On / Off Operation – if you are frequently turning the heater on and off, you may wish to

leave it in continuous pilot. This allows the burner to turn on more quickly, without pilot ignition delay.

Switching from Intermittent (IPI) to Continuous Pilot (CPI)

The pilot mode on this appliance is adjusted using the remote. With the remote in the off position

(thermostat off, manual off), follow the directions below to adjust the pilot mode.

Figure 3

Press the "MODE" button

when the appliance is off to

adjust the IPI/CPI.

NOTE: This icon appears

when the appliance is in

CPI mode. Press the "UP" button

to activate CPI mode.

Press the "DOWN" button

to activate IPI mode.

10 Operation

Remote Operation

When the switch on the battery holder is set to “REMOTE” the transmitter operates the fireplace. Once

you understand how the transmitter works, you will be able to operate your fireplace quickly and easily.

Display Overview

The transmitter display has four main sections (see Figure 4).

Figure 4

Listen for the “Beep”

Each time you press a button on the transmitter that controls the fireplace, a “beep” will come from the

IFC. When you change thermostat target settings the IFC will not beep.

NOTE: When the batteries start to get low, the IFC will beep twice whenever a button is pressed. When

the batteries are nearly depleted, the IFC will no longer beep. See “IFC Batteries” on page 14).

Thermostat Display

Room Temperature Display

Read-Out

(Thermostat Setting,

Function, etc.)

Mode Display (Flame, Blower, Light, Comfort Control)

Inhaltsverzeichnis

Andere Travis Industries Kamin im Innenbereich Handbücher

Travis Industries

Travis Industries Green Smart Bedienungsanleitung

Travis Industries

Travis Industries Small Flush Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries DVS FIREPLACE Bedienungsanleitung

Travis Industries

Travis Industries 864 HO GS Bedienungsanleitung

Travis Industries

Travis Industries Flush Wood Plus Insert Bedienungsanleitung

Travis Industries

Travis Industries 864 HO NB Bedienungsanleitung

Travis Industries

Travis Industries 864 TRVGreenSmart Bedienungsanleitung

Travis Industries

Travis Industries 21 TRV GreenSmart Bedienungsanleitung

Travis Industries

Travis Industries Space Saver IPI Fireplace 564 Bedienungsanleitung

Travis Industries

Travis Industries 564 Cleanface Bedienungsanleitung

Travis Industries

Travis Industries 6015 HO GSR2 Bedienungsanleitung

Travis Industries

Travis Industries DaVinci Bedienungsanleitung

Travis Industries

Travis Industries DVL Insert Bedienungsanleitung

Travis Industries

Travis Industries Cleanface 864 Bedienungsanleitung

Travis Industries

Travis Industries 864 Clean Face Bedienungsanleitung

Travis Industries

Travis Industries DVL EF II Bedienungsanleitung

Travis Industries

Travis Industries 430 GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 1250 Insert Bedienungsanleitung

Travis Industries

Travis Industries 21 DV RV Bedienungsanleitung

Travis Industries

Travis Industries 864 See Through Bedienungsanleitung

Travis Industries

Travis Industries Shadowbox Black Bedienungsanleitung

Travis Industries

Travis Industries 4415 HO GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 4237 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch