Travis Industries 564 HO Bedienungsanleitung

564 HO GS

Fireplace

Tested and Listed by

ANSI Z21.88

Built-In Direct Vent Fireplace

Natural Gas or Propane

Residential or Mobile Home

WARNING: If the information in these instructions is not followed exactly, a fire or

explosion may result causing property damage, personal injury or loss of life.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas

supplier.

This appliance may be installed in

an aftermarket permanently

located, manufactured home (USA

only) or mobile home, where not

prohibited by local codes.

This appliance is only for use

with the type(s) of gas indicated

on the rating plate. A conversion

kit is supplied with the appliance.

Installation Manual

Installer: After installation give this manual to the home-

owner and explain operation of this heater.

www.travisproducts.com

4800 Harbour Pointe Blvd. SW

Mukilteo, WA 98275

2 Introduction

Overview

This manual details the installation requirements for

the 564 HO GS fireplace. For operating and

maintenance instructions, refer to the 564 HO GS

Owner's Manual (part # 100-01264).

Listing Details

This appliance was listed by Intertek Test Labs to

ANSI Z21.88. The listing label is attached to the

appliance near the gas control valve. A copy is

shown to the right.

Massachusetts Approval

This manual has been submitted to the

Massachusetts Board of State Examiners of

Plumbers and Gas Fitters.

National Fireplace Institute

Report No. B100307498PRT-001

Control No. 4000515

Certified for USA and Canada

Tested to: ANSI Z21.88-2009/CSA 2.33-2009 “Vented Gas Fireplace Heaters”, CGA 2.17-M91, UL 307b-2006 “Gas Burning Heating

Appliances for Manufactured Homes”, and CSA P.4.1-09.

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI

Z223.1/NFPA 54, or Natural Gas and Propane Installation Codes, CSA B149.1.

This appliance must be installed in accordance with the current Standard CAN/CSA Z240 MH, Mobile Housing, in Canada or with

the Manufactured Home Constructions and Safety Standard, Title 24 CFR, Part 3280, in the United States, or when such a

standard is not applicable, ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installation Standard.

This vented gas fireplace heater is equipped at the factory for use with natural gas. If conversion to propane (LP) is desired, the

optional factory conversion kit must be used.

This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket,

permanently located, manufactured home (USA only) where not prohibited by local codes. See owner’s manual for details. This

appliance is not convertible for use with other gases, unless a certified kit is used.

This vented gas fireplace heater is not for use with air filters.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

This appliance must be properly connected to a venting system in accordance with the manufacturer’s installation instructions.

Use only approved coaxial direct vent system to vent this appliance to the exterior. See owner’s manual for approved brands of

venting.

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to

the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified

installer, service agency or the gas supplier.

CAUTION: Hot while in operation. Do Not Touch. Severe burns may result. Keep children,

clothing, furniture, gasoline and other liquids having flammable vapors away. Do not operate

this appliance with glass removed, cracked or broken. Replacement of the panel(s) should be

done by a licensed or qualified service person.

VENTED GAS FIREPLACE HEATER - NOT FOR USE WITH SOLID FUEL

MINIMUM CLEARANCES TO COMBUSTIBLES

Fireplace to Adjacent Wall

Wood Floor Beneath Fireplace

Back to Enclosure

12” (305 mm)

0” (0 mm)

Base of Fireplace to Enclosure Top

Sides to Enclosure

Base of Fireplace to a 12” Mantel*

(*See manual for other mantel depths)

56” (1423 mm)

0.5” (13 mm)

48.75” (1239 mm)

Input Rate on “HI” (BTU/Hr)

Input Rate on “LO” (BTU/Hr)

35,000

7,500

35,000

10,400

Minimum Inlet Pressure (inches W.C.)

Maximum Inlet Pressure (inches W.C.)

Manifold Pressure on “HI” (inches W.C.)

11”

13”

10”

5.5”

7”

3.5”

For natural gas when equipped with the following drill size orifice: DMS 50 Front - DMS 44 Back

For propane when equipped with the following drill size orifice: 1.10mm Front - DMS 55 Back

This appliance is equipped for use only at altitudes 0-2000 feet (0-610m) in the USA. In Canada, 0-4500 feet (0-1370m).

For altitudes above 2000 feet, the vent configuration, orifice, or combination of both may need to be changed.

See the owner’s manual for information on making these changes.

Electrical Rating: 115V., 60 Hz, 1.5 Amps

L.P. N.G. L.P. N.G.

2011

2012

2013

Jan.

Feb.

Mar.

Apr.

May

Jun.

Jul.

Aug.

Sep.

Oct.

Nov.

Dec.

Manufacture

Date:

www.travisproducts.com

0962

Table of Contents 3

Overview ...........................................................2

Listing Details...................................................2

Installation Options..........................................6

Heating Specifications.....................................6

Dimensions.......................................................6

Packing List......................................................7

Additional Items Required...............................7

Installation Overview .......................................7

Recommended Installation Procedure ..........8

Massachusetts Requirements ........................9

Requirements for the Commonwealth of

Massachusetts................................................9

MANUFACTURER REQUIREMENTS...........9

Fireplace Placement Requirements.............10

Clearances ...................................................10

Raised Fireplaces.........................................10

Minimum Framing Dimensions.....................11

Nailing Brackets............................................12

Corner Installations.......................................13

Gas Line Requirements.................................14

Fuel...............................................................14

Gas Line Connection....................................14

Gas Inlet Pressure........................................14

Gas Line Location.........................................15

Electrical Connection (required) ..................16

Optional Wall Switch or Thermostat

Installation ......................................................17

Parallel ConnectionSeries Connection 17

Vent Requirements ........................................18

Vent Clearances...........................................18

Altitude Considerations.................................18

Approved Vent..............................................19

Vent Installation............................................19

Approved Vent Configurations.....................20

Restrictor Position........................................20

Exhaust Restrictor Adjustment.....................20

Intake Restrictor Adjustment........................21

Diffuser Plate Adjustment.............................22

Vent Configurations with Horizontal

Termination (EmberFyre Burner only).........23

Vent Configurations with Vertical

Termination (EmberFyre Burner only).........24

Vent Configurations with Horizontal

Termination (Dancing/DiamondFyre)...........25

Vent Configurations with Vertical

Termination (Dancing/DiamondFyre)...........26

Hearth Requirements ....................................28

Facing Requirements ....................................29

Drywall Installation .......................................29

Facing Overview...........................................30

Optional Faceplates – Sizing Chart..............30

Thin Facing Installation (tile, marble, or other

non-combustible under 1" (25mm) thick).....31

Thin Facing Installation (tile, marble, under 1"

(25mm) thick) — Side View..........................32

Thick Facing Installation (stone, brick, or other

non-combustible over 1" (25mm) thick) .......33

Thick Facing with Fireplace Xtrordinair (FPX)

Arched Faces...............................................34

Thick Facing Installation — Side View.........35

Mantel Requirements ....................................36

Combustible Mantels....................................36

Steps for Finalizing the Installation.............36

Air Shutter Adjustment.................................38

Glass Frame Removal and Installation........39

Glass Frame Removal and Installation

(continued) .....................................................40

LP Conversion Instructions..........................41

Installation ..................................................41

Index.............................................................58

4 Safety Precautions

Safety Warnings:

Failure to follow all of the requirements may result in property damage, bodily injury, or even death.

This unit must be installed by a qualified installer to prevent the possibility of an explosion.

This appliance must be installed in accordance with all local codes, if any; if not, in U.S.A. follow ANSI

Z223.1 and NFPA 54(88), in Canada follow CSA B149.1.

A manufactured home (USA only) or mobile home OEM installation must conform with the

Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a

standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS

A225.1, or Standard for Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4. This

appliance may be installed in Manufactured Housing only after the home is site located.

All exhaust gases must be vented outside the structure of the living-area. Combustion air is drawn

from outside the living-area structure. The venting must not be connected to a chimney flue serving a

separate solid-fuel burning appliance.

Notify your insurance company before hooking up this fireplace.

The room heater should be inspected before use and at least annually by a qualified service person.

More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc.

The instructions in this manual must be strictly adhered to. Do not use makeshift methods or

compromise in the installation. Improper installation will void the warranty and safety listing.

This heater is approved for use with natural gas (NG) or propane (LP). Burning the incorrect fuel will

void the warranty and safety listing and may cause an extreme safety hazard. Direct questions about

the type of fuel used to your dealer.

Contact your local building officials to obtain a permit and information on any installation restrictions

or inspection requirements in your area.

If the flame becomes sooty, dark orange in color, or extremely tall, do not operate the heater. Call

your dealer and arrange for proper servicing.

It is imperative that control compartments, screens, or circulating air passageways of the heater be

kept clean and free of obstructions. These areas provide the air necessary for safe operation.

Do not operate the heater if it is not operating properly in any fashion or if you are uncertain. Call

your dealer for a full explanation of your heater and what to expect.

Do not store or use gasoline or other flammable liquids in the vicinity of this heater.

Do not operate if any portion of the heater was submerged in water or if any corrosion occurs.

Immediately call a qualified service technician to inspect the appliance and to replace any part of the

control system and any gas control which has been under water.

Do not place clothing or other flammable items on or near the heater. Because this heater can be

controlled by a thermostat there is a possibility of the heater turning on and igniting any items placed

on or near it.

Light the heater using the built-in igniter. Do not use matches or any other external device to light

your heater.

Never remove, replace, modify or substitute any part of the heater unless instructions are given in this

manual. All other work must be done by a trained technician. Don't modify or replace orifices.

The viewing glass should be opened only for conducting service.

Any safety screen or guard removed for servicing must be replaced prior to operating the heater.

Safety Precautions 5

Safety Warnings (continued):

Allow the heater to cool before carrying out any maintenance or cleaning.

Operate the heater according to the instructions included in this manual.

If the main burners do not start correctly turn the gas off and call your dealer for service.

This unit is not for use with solid fuel.

Do not place anything inside the firebox (except the optional artwork).

Warning: Do not operate appliance with the glass front removed, cracked or broken. Replacement

of the glass should be done by a licensed or qualified service person.

Do not throw this manual away. This manual has important operating and maintenance instructions

that you will need at a later time. Always follow the instructions in this manual.

Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical

barrier is recommended if there are at risk individuals in the house. To restrict access to a fireplace

or stove, install an adjustable safety gate to keep toddlers, young children and other at risk individuals

out of the room and away from hot surfaces.

Children and adults should be alerted to the hazards of high surface temperature and should stay

away to avoid burns or clothing ignition. Do not touch the hot surfaces of the heater. Educate all

children of the danger of a high-temperature heater.

Due to the high temperature, the heater should be located out of traffic and away from furniture and

draperies.

Instruct everyone in the house how to shut gas off to the appliance and at the gas main shutoff valve.

The gas main shutoff valve is usually next to the gas meter or propane tank and requires a wrench to

shut off.

Travis Industries, Inc. grants no warranty, implied or stated, for the installation or

maintenance of your heater, and assumes no responsibility of any consequential damage(s).

6 Installation (for qualified installers only) 6

Installation Options

Residential or Mobile Home

Straight or Corner Placement

Flush or Recessed Face

Raised or Floor Placement

Internal or External Chase

Bedroom Approved

Heating Specifications

Natural Gas Propane

Approximate Heating Capacity (in square feet)* Up to 1,700 Up to 1,700

Maximum BTU Input Per Hour 35,000 35,000

* Heating capacity will vary with floor plan, insulation, and outside temperature.

** Efficiency rating is a product thermal efficiency rating determined under continuous operation

independent of installed system.

Dimensions

(a) Center Location of Vent

(b) Heat Shield (must be bent vertically after fireplace is in location)

30"

762mm

Left

a' gauche

Front

avant

Right

droit

Rear

arrie're

36.25"

921mm

30-1/4"

768mm

33-1/4"

845mm

28-3/4"

730mm

1” 25mm

32.5"

826mm

18.75"

476mm

36-1/2”

928mm

31-3/4”

807mm

6-1/4”

159mm

16-1/2”

420mm

Installation (

for qualified installers only)

Packing List

Propane Conversion Kit

564 HO Thimble (250-02318)

Additional Items Required Direct Vent

Gas Line Equipment

Electrical Equipment

This Fireplace Requires a Burner Kit, Firebacks, Logs/Media, and Face/Grill

This fireplace is shipped without a burner. This allows the fireplace to be configured in one of three

unique designs. See the table below to verify you have all of the items required.

Burner Style EmberFyre™ Burner

96900116 DiamondFyre™

Burner

96900115

DancingFyre™ Burner

96900114

Firebacks Requires 564 Ceramic

Firebacks:

96100179

96100181

96100182

96100183

96100270

96100271

Requires one of the

following:

Stainless 96100249

Enamel Black 96100250

Painted Black 96100251

Included w Burner

(Black Painted)

NOTE: You may use

ceramic or 564 HO

DiamondFyre firebacks,

but they are only installed

on the firebox walls (floor

firebacks are discarded).

Logs/Media Included w Burner Use 564 HO (31 DVI)

Media

Driftwood (94500548)

Other Media To Follow

Included w Burner

Face/Grill Use any 564 Face or Grill Use any 564 Face or Grill Use any 564 Face or Grill

8 Installation (for qualified installers only) 8

Installation Overview

All requirements below must be met.

Recommended Installation Procedure

Frame the opening for the fireplace. Make sure to allow for vent installation.

This fireplace is designed to accommodate 1/2" (13mm) or 5/8" (16mm) drywall (see "Nailing

Brackets" on page 12 for details). Secure the fireplace to the framing.

Install the vent, gas line and electrical hook-up.

Install the drywall.

Install the hearth (if applicable).

Install the facing (if applicable).

Install the mantel (if applicable).

Finalize the installation (see page 36) and install the grill or face.

Drywall

See the section

“Mantel Requirements”

Drywall

Side

Wall 12” min.

305mm

See “Optional Non-

Combustible Facing” See “Optional Non-

Combustible Hearth”

See the section

“Electrical Connection”

See the section

“Vent Requirements”

See the section

“Approved Vent

Configurations”

Nailing brackets

See the section

“Minimum Framing

Dimensions”

See the section

“Gas Line Installation”

Installation (for qualified installers only) 9

Massachusetts Requirements

NOTE: The following requirements reference various Massachusetts and national codes not contained in this document.

Requirements for the Commonwealth of Massachusetts

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in

part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent

termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and

porches, the following requirements shall be satisfied:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gasfitter shall

observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor level where the

gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery operated or hard

wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served

by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the

services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired

carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.

In the event that the requirements of this subdivision cannot be met at the time of completion of installation, the owner shall

have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day

period, a battery operated carbon monoxide detector with an alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be

ANSI/UL 2034 listed and IAS certified.

Signage

A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight

(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or

equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP

CLEAR OF ALL OBSTRUCTIONS”.

Inspection

The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation

unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the

provisions of 248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08(2) (a) 1 through 4:

• The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54

as adopted by the Board; and

• Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the

dwelling, building or structure used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or

venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment

and the venting system shall include:

• Detailed instructions for the installation of the venting system design or the venting system components; and

• A complete parts list for the venting system design or venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts

for venting the flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by the

manufacturer:

• The referenced “special venting system” instructions shall be included with the appliance or equipment installation

instructions; and

• The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a

parts list and detailed installation instructions.

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting

instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or

equipment at the completion of the installation.

See Gas Connection section for additional Commonwealth of Massachusetts requirements.

10 Installation (for qualified installers only) 10

Fireplace Placement Requirements

The fireplace requires a 1/2" (13mm) clearance from the angled sides of the fireplace to the framing

members. No material (insulation, framing, etc.) may be placed into this area.

Fireplace must be installed on a level surface capable of supporting the fireplace and vent

Fireplace must be placed directly on wood or non-combustible surface (not on linoleum or carpet)

This heater may be placed in a bedroom. Please be aware of the large amount of heat this appliance

produces when determining a location.

Clearances

When installed, walls in front of the fireplace must be a minimum 12" (305mm) to the side of the

fireplace.

Due to the high temperature, the heater should be located out of traffic and away from furniture and

draperies.

Fireplace must be placed so the vents below and above the glass do not become blocked.

Raised Fireplaces

The fireplace (and hearth, if desired) may be placed on a platform designed to support the fireplace

(155 lbs., 70Kg) and vent.

Andere Handbücher für 564 HO

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Travis Industries Kamin im Innenbereich Handbücher

Travis Industries

Travis Industries 36 CF ST/Pier Bedienungsanleitung

Travis Industries

Travis Industries 564 HO Bedienungsanleitung

Travis Industries

Travis Industries 21 TRV GreenSmart Bedienungsanleitung

Travis Industries

Travis Industries LOPI X Bedienungsanleitung

Travis Industries

Travis Industries 21 DV RV Bedienungsanleitung

Travis Industries

Travis Industries 864 Clean Face Bedienungsanleitung

Travis Industries

Travis Industries Fireplace Xtrordinair 864 GSR2 Bedienungsanleitung

Travis Industries

Travis Industries Shadowbox Black Bedienungsanleitung

Travis Industries

Travis Industries 1750 Bedienungsanleitung

Travis Industries

Travis Industries DVL GSR2 NB Bedienungsanleitung

Travis Industries

Travis Industries 6015 HO GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 99200149 Bedienungsanleitung

Travis Industries

Travis Industries 4415 HO GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 33 DVI Cypress Bedienungsanleitung

Travis Industries

Travis Industries 21 DV RV Bedienungsanleitung

Travis Industries

Travis Industries 33 DVI Log Set Bedienungsanleitung

Travis Industries

Travis Industries DVS EF Fireplace Bedienungsanleitung

Travis Industries

Travis Industries 864 HO NB GSR2 Bedienungsanleitung

Travis Industries

Travis Industries EmberGlo 616 Bedienungsanleitung

Travis Industries

Travis Industries Cleanface 864 Bedienungsanleitung

Travis Industries

Travis Industries 4237 Bedienungsanleitung

Travis Industries

Travis Industries 616 Diamond-Fyre GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Bedienungsanleitung

Travis Industries

Travis Industries Granite 99600200 Service-Handbuch

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch