Travis Industries 864 ST GS Bedienungsanleitung

864 ST

Fireplace

Installation

Manual

Tested and Listed by

OMNI-Test

Laboratories, Inc.

Beaverton, Oregon

• Built-In Direct Vent Fire lace

• Natural Gas or Pro ane

• Residential or Mobile Home

Re ort # 028-F-84-5

ANSI Z21.88b-2003

ARNING: If the information in these instructions is not followed exactly, a fire or

explosion may result causing property damage, personal injury or loss of life.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance.

HAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the

gas supplier.

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only)

or mobile home, where not prohibited by local codes.

This appliance is only for use with the type(s) of gas indicated on the rating plate. A conversion kit is

supplied with the appliance.

INSTALLER:Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

 Co yright 2007, T.I. $10.00 100-01195_000 4071126

4800 Harbour Pointe Blvd. SW

Mukilteo, WA 98275

2 Introduction

Overview

This manual details the installation

requirements for the 864 ST (See Through)

fire lace. For o erating and maintenance

instructions, refer to the 864 ST Owner's Manual

( art # 100-01196).

Listing Details

This a liance was listed by OMNI-Test

Laboratories, Inc. to ANSI Z21.88 - re ort # 028-

F-84-5. The listing label is attached to the

a liance near the gas control valve. A co y is

shown to the right.

IAS (ICBO) Approval

This a liance was listed by OMNI-Test

Laboratories, Inc. - IAS # TL130 ( reviously

ICBO).

Massachusetts Approval

This manual has been submitted to the

Massachusetts Board of State Examiners of

Plumbers and Gas Fitters

National Fireplace Institute

Table of Contents 3

Introduction

Overview.................................................................2

Listing Details..........................................................2

Safety Precautions

Safety Precautions...................................................4

Features and Specifications

Features.................................................................6

Installation O tions...................................................6

Heating S ecifications .............................................. 6

Dimensions.............................................................6

Installation

Packing List.............................................................7

Additional Items Required..........................................7

Recommended Installation Procedure .........................7

Massachusetts Requirements..................................... 8

To Vent or Side Vent Configuration............................9

Converting the Fire lace to Side Vent Configuration...9

Fire lace Placement Requirements.............................11

Clearances...........................................................11

Raised Fire laces .................................................11

Min. Framing Dims................................................12

Nailing Brackets....................................................13

Gas Line Requirements............................................. 14

Fuel ....................................................................14

Gas Line Connection .............................................14

Gas Inlet Pressure ................................................14

Gas Line Location .................................................15

Electrical Connection (required).................................. 16

Wall Switch or Thermostat Installation .........................17

Wiring Diagram (Millivolt System) ............................17

Wall Switch Installation...........................................17

Vent Requirements...................................................18

Vent Clearances ...................................................18

Altitude Considerations ..........................................18

A roved Vent......................................................19

Vent Installation....................................................19

A roved Vent Configurations ....................................20

Restrictor Position.................................................20

Exhaust Restrictor Adjustment................................20

Intake Restrictor Adjustment...................................21

Diffuser Plate Adjustment.......................................22

Side Vent Config. W Horizontal Term. (no vertical rise).. 23

Side Vent Config. W Horizontal Term. (w vertical rise)....24

Side Vent Configuration with Vertical Termination ..........25

To Vent Configuration with Horizontal Termination........26

To Vent Configuration with Vertical Termination ........... 27

Termination Requirements.........................................28

Installation (continued)

Hearth Requirements ............................................... 29

Facing Requirements ............................................... 30

Drywall Installation ................................................ 30

Facing Overview ...................................................31

O tional Face lates – Sizing Chart ..........................31

Thin Facing Installation..........................................32

Thick Facing Installation.........................................34

Thick Facing Installation with FPX Arched Faces........35

Mantel Requirements................................................ 37

Install Exam le - Build-Out (Dog-House) w Hor. Term.... 37

Finalizing the Installation

Ste s for Finalizing the Installation ............................. 38

Starting the Pilot Flame ......................................... 38

Pilot Flame Ins ection...........................................38

Air Shutter Adjustment...........................................39

Glass Frame Removal and Installation........................ 40

Log Set Installation .................................................. 42

Optional Equipment

LP Conversion Instructions ....................................... 52

Fireback Installation ................................................. 56

Grill Installation........................................................ 58

Remote Control Receiver Installation (2 O tions) ......... 59

Extra Room Power Heat Duct (sku 98500769)............ 60

Andiron Installation................................................... 61

Index

Index...................................................................... 62

4 Safety Precautions

Travis Industries 4071126 100-01195_000

Safety Warnings:

• Failure to follow all of the requirements may result in property damage, bodily injury, or even death.

• This unit must be installed by a qualified installer to prevent the possibility of an explosion.

• This appliance must be installed in accordance with all local codes, if any; if not, in U.S.A. follow ANSI

Z223.1 and NFPA 54(88).

• In Manufactured or Mobile Homes must confirm with: In USA, Manufactured Home Construction and

Safety Standard, Title 24 CFR, Part 3280, or, when such a standard is not applicable, the Standard for

Manufactured Home Installations, ANSI/NCSBCS A225.1. This appliance may be installed in

Manufactured Housing only after the home is site located.

• All exhaust gases must be vented outside the structure of the living-area. Combustion air is drawn

from outside the living-area structure.

• Notify your insurance company before hooking up this fireplace.

• The room heater should be inspected before use and at least annually by a qualified service person.

More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc.

• The instructions in this manual must be strictly adhered to. Do not use makeshift methods or

compromise in the installation. Improper installation will void the warranty and safety listing.

• This heater is approved for use with natural gas (NG) or propane (LP). Burning the incorrect fuel will

void the warranty and safety listing and may cause an extreme safety hazard. Direct questions about

the type of fuel used to your dealer. Check the label and flame adjust knob on the gas control valve.

• Contact your local building officials to obtain a permit and information on any installation restrictions or

inspection requirements in your area.

• If the flame becomes sooty, dark orange in color, or extremely tall, do not operate the heater. Call your

dealer and arrange for proper servicing.

• It is imperative that control compartments, screens, or circulating air passageways of the heater be

kept clean and free of obstructions. These areas provide the air necessary for safe operation.

• Do not operate the heater if it is not operating properly in any fashion or if you are uncertain. Call your

dealer for a full explanation of your heater and what to expect.

• Do not store or use gasoline or other flammable liquids in the vicinity of this heater.

• Do not operate if any portion of the heater was submerged in water or if any corrosion occurs.

• Do not place clothing or other flammable items on or near the heater. Because this heater can be

controlled by a thermostat there is a possibility of the heater turning on and igniting any items placed

on or near it.

• Light the heater using the built-in piezo igniter. Do not use matches or any other external device to

light your heater.

• Never remove, replace, modify or substitute any part of the heater unless instructions are given in this

manual. All other work must be done by a trained technician. Don't modify or replace orifices.

• The viewing glass should be opened only for lighting the pilot or conducting service.

• Any safety screen or guard removed for servicing must be replaced prior to operating the heater.

Safety Precautions 5

Safety Warnings (continued):

• Allow the heater to cool before carrying out any maintenance or cleaning.

• Operate the heater according to the instructions included in this manual.

• If the main burners do not start correctly turn the gas off at the gas control valve and call your dealer for

service.

• The pilot flame must contact the thermopile and thermocouple. If it does not, turn the gas control

valve to "OFF" and call your dealer.

• This unit is not for use with solid fuel.

• Do not place anything inside the firebox (except the included logs).

• If the fiber logs become damaged, replace with Travis Industries log set.

• Do not throw this manual away. This manual has important operating and maintenance instructions

that you will need at a later time. Always follow the instructions in this manual.

• Do not touch the hot surfaces of the heater. Educate all children of the danger of a high-temperature

heater. Young children should be supervised when they are in the same room as the heater.

• Due to the high temperature, the heater should be located out of traffic and away from furniture and

draperies.

• Instruct everyone in the house how to shut gas off to the appliance and at the gas main shutoff valve.

The gas main shutoff valve is usually next to the gas meter or propane tank and requires a wrench to

shut off.

• Travis Industries, Inc. grants no warranty, implied or stated, for the installation or

maintenance of your heater, and assumes no responsibility of any consequential

damage(s).

6 Features and Specifications

Travis Industries 4071126 100-01195_000

Installation Options

• Residential or Mobile Home

• Flush or Recessed Face

• Raised or Floor Placement

• Internal or External Chase

• Horizontal or Vertical Vent

• Bedroom A roved

Heating Specifications

Natural Gas Propane

A roximate Heating Ca acity (in square feet)* U to 1,500 U to 1,500

Maximum BTU In ut Per Hour 37,500 37,500

* Heating ca acity will vary with floor lan, insulation, and outside tem erature.

Dimensions

AAAAAAAAAAAA

Side Vent Configuration

8" Diameter Vent

38-1/4"

41"

24"

Top Vent Configuration

8" Diameter Vent

eight: 310 Lbs.

35-1/4"

AAAAAAAAAAAA

AAAAAAAAAAAAA

37"

38-1/4"

39-1/8"

33-7/8"

41-1/2"

4-3/8"

3-3/8"

Right

Left

Front

Back

42-1/2"

Lifting Handle Tabs

These tabs may be

used in conjuction with

the lifting handles

(98500711) - make sure

to use the required

ada ters (250-01038)

Finalizing the Installation (for qualified installers only) 7

Packing List

• Propane Conversion Kit

• Log Set

• Wall Swit h with Wire (see page 17 for details)

• Firestop (sku 93006094)

Additional Items Required

• Dire t Vent

• Gas Line Equipment (shutoff valve, pipe, et .)

• Ele tri al Equipment (min. 14 gauge, grounded line)

• Two Grill Kits and/or Fa es

Recommended Installation Procedure

• Prepare the framing, making sure to leave the area around the firepla e open (see page

12). Make sure to allow for vent installation and fa ing depth.

• Pla e the firepla e into position.

• Install the vent, gas line and ele tri al hook-up.

• Finalize the framing around the firepla e.

• Se ure the firepla e to the framing.

• Install the wall swit h (see page 17) or thermostat (if appli able).

• Install the drywall.

• Install the hearth (if appli able).

• Install the fa ing (if appli able).

• Install the mantel (if appli able).

• Finalize the installation (see page 38) and install the grill or fa e.

8 Finalizing the Installation (for qualified installers only)

Travis Industries 4071126 100-01195_000

Massachusetts Requirements

NOTE: The following requirements reference various Massachusetts and national codes not contained in this document.

Requirements for the Commonwealth of Massachusetts

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in

part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent

termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and

porches, the following requirements shall be satisfied:

Installation of Carbon onoxide Detectors

At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gasfitter shall

observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor level where the

gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery operated or hard

wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served

by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the

services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired

carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.

In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall

have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day

period, a battery operated carbon monoxide detector with an alarm shall be installed.

Approved Carbon onoxide Detectors

Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be

ANSI/UL 2034 listed and IAS certified.

Signage

A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight

(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or

equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP

CLEAR OF ALL OBSTRUCTIONS”.

Inspection

The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation

unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the

provisions of 248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

• The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as

adopted by the Board; and

• Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the

dwelling, building or structure used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or

venting system components with the equipment, the instructions provided by the manufacturer for installation of the

equipment and the venting system shall include:

• Detailed instructions for the installation of the venting system design or the venting system components; and

• A complete parts list for the venting system design or venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts

for venting the flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by the

manufacturer:

• The referenced “special venting system” instructions shall be included with the appliance or equipment installation

instructions; and

• The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a

parts list and detailed installation instructions.

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting

instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or

equipment at the completion of the installation.

See Gas Connection section for additional Commonwealth of Massachusetts requirements.

Finalizing the Installation (for qualified installers only) 9

Top Vent or Side Vent Configuration

This applian e is shipped in the top vent onfiguration. To hange to the side vent onfiguration,

follow the dire tions below.

NOTE: the vent onfiguration affe ts several aspe ts of installation (framing, maximum vent rise,

maximum vent run). When reviewing the installation requirements make sure to pay attention to the

type of onfiguration being used.

Converting the

Fireplace to

Side Vent

Configuration

Remove the back plate on

the fireplace.

NOTE: Use a magnetic-tipped

nutdriver on these screws -

take care to prevent the

screws from falling into the

fireplace.

AAAAAAAA

Remove the flue assembly.

Tuck the two 24" pieces of insulation

into the area between the exhaust

manifold and fireplace can.

WARNING: Failure to properly

place the insulation will void the

warranty and create a safety

hazard.

10 Finalizing the Installation (for qualified installers only)

Travis Industries 4071126 100-01195_000

Converting

the Fireplace

to Side Vent

(continued)

AAAAAAAA

AAAAAA

AAAAAAAA

AAAAAAAAA

Re-attach the flue assembly

in the side position.

Tuck the two 20" pieces of insulation

into the area above the exhaust

manifold and fireplace can. Note how

the insulation is folded in half and

covers the entire area above the

exhaust manifold (see illustration

below).

WARNING: Failure to properly

place the insulation will void the

warranty and create a safety

hazard.

Re-attach the back plate to the

top of the fireplace.

NOTE: Make sure the flange on

the back plate tucks between the

fireplace and the flue assembly.

Andere Handbücher für 864 ST GS

Inhaltsverzeichnis

Andere Travis Industries Kamin im Innenbereich Handbücher

Travis Industries

Travis Industries Avalon Ashpan Bedienungsanleitung

Travis Industries

Travis Industries Fireplace Xtrordinair 864 GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 430 GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 564 Clean Face GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 35 CB Australian Bedienungsanleitung

Travis Industries

Travis Industries Revolution 36CF Bedienungsanleitung

Travis Industries

Travis Industries Fire Garden 40x24 Single Sided Bedienungsanleitung

Travis Industries

Travis Industries Travis DVL Bedienungsanleitung

Travis Industries

Travis Industries Fireplace Xtrordinair CoolSmart TV Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Bedienungsanleitung

Travis Industries

Travis Industries 864 ST GS Bedienungsanleitung

Travis Industries

Travis Industries Cleanface 864 Bedienungsanleitung

Travis Industries

Travis Industries Xtrordinair 44 Elite Bedienungsanleitung

Travis Industries

Travis Industries 42 ProBuilder GSB2 Bedienungsanleitung

Travis Industries

Travis Industries LOPI X Bedienungsanleitung

Travis Industries

Travis Industries Avalon Rosario Winthrop 864 Bedienungsanleitung

Travis Industries

Travis Industries Revolution 36CF Bedienungsanleitung

Travis Industries

Travis Industries 42 ProBuilder MV Bedienungsanleitung

Travis Industries

Travis Industries 21 TRV GreenSmart Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart 2 Fireplace 564 SS GSR2 Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Bedienungsanleitung

Travis Industries

Travis Industries 21 TRV GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 864 ST GSR2 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch