TRENDnet TEW-445UB Bedienungsanleitung
TEW-445UB
Quick Installation Guide
Table of Contents
Table of Contents
Version 10.04.2006
English .....................................................................................................
Troubleshooting ........................................................................................
1
1
2
5
7
1. Before You Start
2. How to Install .....................................................................................
3. Wireless Configuration ......................................................................
................................................................................
System Requirements
Application
TEW-445UB
Utility & Driver CD-ROM
Quick Installation Guide
2 dbi Detachable Antenna
CD-ROM Drive
Computer with an available USB 1.1 or 2.0 port
CPU: 300 MHz or above
Memory: 32MB or above
Windows XP/2000/ME/98SE
Package Contents
1. Before You Start
English
1
Workstation with 108Mbps 802.11g
High Power Wireless USB 2.0 Adapter
(TEW-445UB)
Workstation with
108Mbps Wireless
PCI Adapter
(TEW-443PI)
108Mbps Wireless
Access Point
(TEW-450APB)
Notebook with 108Mbps
Wireless PC Card
(TEW-441PC)
Cable/DSL 4-Port
Firewall Router
(TW100-BRF114)
Cable/DSL
Modem
Internet
USB 2.0 Extension Cable
(Type A to Mini-B)
2. How to Install
English
2
Important! DO NOT connect the Wireless USB Adapter to your computer until
instructed to do so.
1. Insert the Utility & Driver
CD-ROM into your computer's
CD-ROM Drive and then click
Install Utility & Driver. Then click
Windows 2000/XP.
2. Click Run.
3. Click Run.
4. When you reach this screen, select
Install Client Utilities and Drivers
and then click Next.
English
3
6. When you reach this screen, click
Next. (Windows XP only)
5. Click Yes.
7. Select WLAN Client Utility (ACU)
and Supplicant and then click
Next. (Windows XP only)
Note: The TEW-445UB is hot-pluggable, you can connect or disconnect the
TEW-445UB while the computer is on.
8. Plug in the provided USB cable
into the TEW-445UB and into an
available USB plug on your
computer.
9. When the Found New Hardware
wizard appears, click cancel.
10. Click OK.
11. Click Yes.
(Windows 2000)
11. Click Continue
Anyways.
(Windows XP)
Your installation is now complete.
12. Select Yes, I want to restart my
computer now and then click
Finish.
English
4
3. Wireless Configuration
Note: Wireless configuration requires a 802.11g or 802.11b Access Point (for
Infrastructure Mode) or another 802.11g wireless adapter (for Ad-Hoc/Peer-to-
Peer networking mode).
1. Double-click the Wireless icon.
2. Click on Profile Management,
then click on Scan.
3. Click on the proper SSID,
and then click on Activate.
4. Type in a Profile Name, then click
on OK.
English
5
Wireless installation is now complete.
For detailed information regarding the TEW-445UB configuration and advanced
settings, please refer to the User's Guide included on the Utility & Driver
CD-ROM or TRENDnet's website at www.trendnet.com
5. Verify that there is signal strength.
The configuration is now complete.
6
English
7
Troubleshooting
Q1:
A1:
Q2:
A2:
Q3:
A3:
Q4:
A4:
Q5:
A5:
I inserted the Utility & Driver CD-ROM into my computer's CD-ROM Drive and the installation
menu does not appear automatically. What should I do?
If the installation menu does not appear automatically, click Start, click Run, and type
D:\setup.exe where "D" in "D:\setup.exe" is the letter assigned to your computer's CD-
ROM Drive. And then click OK to start the installation.
When I open up the utility, all the buttons are greyed out.
Verify that the device is installed properly. Right click on My Computer -> Properties. Click
on Hardware, then Device Manager. Double click on Network Adapters. Make sure that WLAN
USB 2.0 Wireless Network Adapter is listed and there is no yellow question mark or exclamation
point. Also perform a reboot on the computer.
When I click on Scan, I can not see my SSID.
Log on to your wireless router or access point and make sure that the SSID broadcast option is
not disabled. Make sure the wireless light on your wireless router or access point is on.
First, verify that the Network Name (SSID) matches your wireless router or wireless access
point's SSID. Second, check your TCP/IP properties to ensure that Obtain an IP address
automatically is selected. Third, click Profile Management -> Scan in the Wireless Client Utility to
check and see if there are any available wireless networks listed.
The utility program shows good signal strength, but I can not get onto the Internet.
First, log on to your wireless router or access point and check to see if encryption is enable. If
encryption is enabled, go to Profile Management -> Modify -> Security. Select the proper
Security Options, click on configure, then put in the proper encryption key. Then click Ok.
Second, make sure to disable any firewall programs. Third, make sure that your router is properly
configured for Internet.
If you still encounter problems or have any questions regarding the TEW-445UB, please refer to the
User's Guide included on the Utility CD-ROM or contact TRENDnet's Technical Support Departmen
I completed all the steps in the Quick Installation Guide, but my Wireless USB Adapter isn't
connecting to my access point. What should I do?
Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may
cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de
alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al
mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador
de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria
existente en el pais o zona de instalación.
Andere Handbücher für TEW-445UB
3
Inhaltsverzeichnis
Andere TRENDnet Adapter Handbücher
TRENDnet
TRENDnet TBW-105UB Bedienungsanleitung
TRENDnet
TRENDnet TPL-302E Bedienungsanleitung
TRENDnet
TRENDnet TEW-644UB Bedienungsanleitung
TRENDnet
TRENDnet TU3-ETG Bedienungsanleitung
TRENDnet
TRENDnet TE100-ECFX Bedienungsanleitung
TRENDnet
TRENDnet TFW-H3PI Bedienungsanleitung
TRENDnet
TRENDnet TU3-ETGH3 Bedienungsanleitung
TRENDnet
TRENDnet Powerline 1300 AV2 Adapter with Built-in... Bedienungsanleitung
TRENDnet
TRENDnet TEW-648UB - 150Mbps Mini Wireless N USB 2.0... Bedienungsanleitung
TRENDnet
TRENDnet TEW-429UB Bedienungsanleitung
TRENDnet
TRENDnet TPL-405E Bedienungsanleitung
TRENDnet
TRENDnet TE100-PCI Bedienungsanleitung
TRENDnet
TRENDnet TU2-ET100 Bedienungsanleitung
TRENDnet
TRENDnet TPL-304E2K Bedienungsanleitung
TRENDnet
TRENDnet TEW-684UB - Bedienungsanleitung
TRENDnet
TRENDnet TVP-SP5G Bedienungsanleitung
TRENDnet
TRENDnet TEW-509UB Bedienungsanleitung
TRENDnet
TRENDnet TEW-664UB Bedienungsanleitung
TRENDnet
TRENDnet TEW-649UB Bedienungsanleitung
TRENDnet
TRENDnet TEW-624UB Bedienungsanleitung
