TRENDnet TPL-4052E Bedienungsanleitung

TPL-4052E User’s Guide

TPL-4052E User’s Guide Table of Contents

Table of Contents

Product Overview��1

Package Contents�� 1

Features �� 1

Product informaon on device label �� 2

Push Buons�� 3

Diagnosc LEDs�� 3

Applicaon Diagram �� 4

Install Your Powerline Adapter ��5

Before you Install �� 5

Connect a Powerline Adapter to your router �� 5

Add adapters to your network�� 6

Secure Your Powerline Network ��7

Using the Sync buon�� 7

Change the network name and associate two Powerline Adapters: 8

Add adapters using the Sync buon�� 8

Congure an addional Powerline Adapter to connect and use the

network name of your exisng powerline network:�� 9

Using the Powerline Ulity��9

Powerline Ulity System Requirements�� 10

Soware Installaon�� 10

Using the Ulity �� 13

Powerline Ulity - Map View �� 14

Powerline Ulity - Detailed View�� 16

Powerline Ulity - Device Setup �� 17

Powerline Ulity - Advanced �� 18

Powerline Ulity - Opons�� 19

Powerline Ulity - About �� 20

Technical Specicaons ��21

Troubleshoong ��22

Appendix��23

Overlapping powerline networks �� 23

Move Powerline Adapters between dierent overlapping powerline

networks �� 23

Federal Communicaon Commission Interference Statement��25

RoHS �� 25

Europe – EU Declaraon of Conformity�� 25

Limited Warranty �� 27

TPL-4052E User’s Guide Product Overview

Product Overview

Package Contents

TPL-4052E package includes:

• TPL-4052E: 4-Port Powerline 500 AV Adapter

• Mul-language Quick Installaon Guide

• CD-ROM (Ulity & User’s Guide)

• Network cable (1.5 m / 5 .)

TPL-4052E

Features

TRENDnet’s 4-Port Powerline 500 AV Adapter, model TPL-4052E, uses

an electrical outlet to create a 500 Mbps powerline network. Two

adapters are needed to start a network. Connect network ready TVs,

media players, game consoles, and computers to the four Ethernet

ports. No CD installaon required—encrypted TRENDnet adapters auto-

connect out of the box. This adapter will automacally connect to other

out of box TRENDnet Powerline AV adapters. No installaon required.

(To add up privacy on top of your network, TRENDnet recommends

using buon pressing sequence to scramble network name instead

leave the key public as set in default.) Power saving mode reduces

up to 80% electric consumpon when network is idle. QoS, Quality

of Service, technology priorizes video, audio, and online gaming,

smoothing your streaming experience. LED lamps indicate device and

port status for network monitoring and easy troubleshoong. Advanced

AES encrypon secures your network. This adapter is ideal for use in

buildings that interfere with wireless networking signals.

• Compliant with IEEE1901 and HomePlug AV standards

• High speed networking over an exisng electrical system

• 4 x 10/100 Mbps Auto-MDIX Fast ports

• One-touch Sync buon networks adapters quickly

• Three LED indicators: Power (on/o), Powerline Link (green (best),

amber (beer), red (good), o(no connecon), Ethernet Link

(solid, blinking, o)

• Connect one Powerline 500 AV Adapter to the Internet and then

plug in up to 15* addional Powerline 500 AV Adapters for instant

connecvity

• Share data intensive les, play games, download music and more

at faster data transfer rates

• Advanced 128-bit AES encrypon to ensure total network security

• Power Save mode reduces electric consumpon by 80%

• Network signal transmits up to 300 meters (984.)

• Auto QoS support through trac classicaon and mulple

priority queuing

TPL-4052E User’s Guide Product Overview

• Oponal management ulity compable with Windows 8 (32/64-

bit), Windows

* 8 acve adapter can stream data at the same me. Up to 16 adapters

can be congured in the same network. Addional adapters may decrease

network performance. 500Mbps is the maximum theorecal powerline data

rate. Actual throughput will vary depending on the environment. Networked

Powerline devices must be plugged into power outlets that are on the

same electrical system. GFCI outlets and AFCI circuit breakers may degrade

powerline network signals.

Product informaon on device label

Model Number

Serial Number

Network MAC Address

Device Password (DPW)

Hardware version

Firmware version

Power (PWR) LED

Powerline (PL) LED

Network 1 ~ 4 {

Power plug

Plugs directly into an

available power outlet.

Not on power strip�

Reset buon

Resets the unit to factory

defaults.

Sync buon

Synchronize with other

Powerline Adapters.

Connect network cables

from Powerline Adapter

to your computer, game

console, network TV, and

other network devices.

TPL-4052E User’s Guide Product Overview

Push Buons

Buon Acon Funcon

Sync

(see Using

the Sync

Buon

Secon for

instrucons)

Push and hold

for 2 seconds

Iniate Sync/Connecon and generate random

private network name on rst adapter (PWR

LED will start blinking).

Match the network name on secondary

or addional adapter and connect to rst

adapter. (PWR LED will start blinking)

Note: To establish connecvity, the secondary

or addional Powerline Adapter’s Sync buon

must also be pushed within 2 minutes (120

sec) of pushing the Sync buon of the rst

adapter�

Push/hold for

15 seconds

Erases the network name

(All LEDs will turn o and turn back on).

Reset Push/Hold for

1 second only

Reset device to factory defaults (All LEDs will

turn o and turn back on).

Note: Will reset to the factory default private

network name “HomePlug AV”.

Save Mode: The device will automacally standby to reduce power usage when there

is no network trac for more than 10~20 minutes. It will automacally resume back

to full speed service when trac resumes.

Diagnosc LEDs

Indicates the device and connecon status

LED Color Sequence Denion

PWR

(Power)

Green Solid Device powered on

N/A O Device powered o

(Powerline)

Green

Solid Powerline connected (Best)

Blinking Syncing or Powerline data

transming/receiving (Best)

Amber

Solid Powerline connected (Beer)

Blinking Powerline data transming/receiving

(Beer)

Red

Solid Powerline connected (Good)

Blinking Powerline data transming/receiving

(Good)

N/A O Powerline is not synced or

connected

1-4

(Fast

Ethernet

Connecon)

Green Solid Network connecon established

Blinking Data transmission is detected

N/A O Network standby or no network

connecon

Note: Powerline (PL) LED color indicates the strength and quality of the Powerline

connecon through the electrical system. The following factors may aect the

powerline network’s connecon quality:

•

Noise – Generated by appliances which use your electrical system (e.g.

Microwaves, ovens, hair dryer, irons, dishwashers, etc.). The quality of your

household electrical wiring may also cause addional noise on your electrical

system.

•

Distance – Long lengths of electrical wiring through your electrical system

between connected Powerline Adapters.

TPL-4052E User’s Guide Product Overview

Applicaon Diagram

Diagram Explanaon:

The rst Powerline unit is networked

to a router which is in turn

connected to a modem (typically

supplied by your Internet Service

Provider (ISP)) that provides Internet

connecvity. A second Powerline

Adapter is plugged into a wall power

outlet near a media center and is

providing Internet connecvity to a

game a game console and a Blu-ray

player / media player via Ethernet.

TPL-4052E User’s Guide Installing Your Powerline Adapter

Installing Your Powerline Adapter

Before you install

1. Before you proceed with the installaon, verify the following:

• Verify that you already have Internet access through your

exisng network.

• Verify that you have an available Ethernet port (also known as a

LAN port) on you router.

• Verify that you have at least two Powerline Adapters. Two or

more Powerline Adapters are required to create a powerline

network�

Note: The TPL-4052E package only includes a single Powerline

Adapter. Please ensure that your other Powerline Adapter is

HomePlug® AV or IEEE 1901 compliant (e.g. TRENDnet models

TPL-401E, TPL-402E, TPL-405E , TPL-406E , TPL-407E or another

TPL-4052E.)

2. Plan the locaon of where you will install your Powerline Adapters.

• Avoid plugging the adapters into power strips, extension cords,

or surge protectors as this may prevent the adapter from

funconing correctly or degrade performance.

• Avoid plugging the adapters into wall power outlets that are

controlled by a light switch to prevent the Powerline Adapter

from being turned o accidentally.

• Avoid plugging the adapters into wall power outlets that

are located near appliances that consume a lot of power

(e.g. refrigerators, washers, dryers) as this may degrade

performance�

• Make sure there is an available wall power outlet in the room

where the router is installed and also near the router.

• Make sure there is an available wall power outlet in the room

where you want to extend network connecvity.

Connecng a Powerline Adapter to your router

1. Plug the Powerline Adapter into an available wall power outlet near

your router�

Note: This will allow devices connected to your powerline network to

access the Internet and other devices connected to your network.

2. Connect the included Ethernet cable (also called a network cable)

from the Ethernet port (also called network port) of your Powerline

Adapter to an available Ethernet port (also called LAN port) on your

router�

3. Once the Powerline Adapter is installed and connected to your

router, verify that the Power (PWR) LED is on or blinking and the

Network LED is on or blinking.

TPL-4052E

TPL-4052E User’s Guide Installing Your Powerline Adapter

Adding adapters to your network

Once you have installed and connected the rst Powerline Adapter

to your router, you can easily extend your network to other rooms by

adding addional Powerline Adapters.

To extend your network using an addional Powerline Adapter:

1. First, make sure the rst Powerline Adapter is installed and

connected to your router�

Note: This will allow devices connected to your powerline network to

access the Internet and other devices connected to your network. See

“Connecng a Powerline Adapter to your router” on page 5.

2. Plug in the addional Powerline Adapter to an available wall power

outlet in another room near a computer or network device (e.g. game

consoles, network-enabled TVs, network aached storage, network

media server/players, etc.) you want to connect to your network.

3. Connect one end of the included Ethernet cable to the Ethernet

port on your Powerline Adapter and then connect the other end to the

Ethernet port on your computers or another network enabled device.

4. Aer the addional Powerline Adapter is connected and installed to

your computer or network device, wait for the Powerline (PL) LED to

turn on. Aer the Powerline (PL) LED turns on, verify that the Power

(PWR) LED is on, the Powerline (PL) LED is on or blinking, and the

network LED is on or blinking.

Note: To verify that your Powerline Adapters are connected successfully

to your network, you can check if the computer(s) or network device(s)

can access the Internet through your powerline network.

To install addional Powerline Adapters in other rooms, repeat the

steps above for each adapter�

TPL-4052E User’s Guide Securing Your Powerline Network

Secure Your Powerline Network

Powerline Adapters join powerline network by using network name.

The default network name is “HomePlugAV”. All out-of-the-box

TRENDnet HomePlugAV Powerline Adapters have the same default

network name and can be connected to each other without further

conguraon. To add network security to your network, you can change

your Powerline network name away from the factory default name.

With a private custom network name, no one can connect to your

Powerline network with an out-of-the-box HomePlugAV adapter.

TRENDnet recommends you change the Powerline network name

away from the factory default name to increase network security. Once

congured, the Powerline network name will be saved. The adapter

can be moved freely within its operang range without having to

recongure the network name. If a mistake is made in the sengs,

the adapter can be reset to the factory default sengs by pressing the

reset Reset buon for 1 second.

There are two ways to change the default network name:

1� (Recommended) Use the physical Sync buon on your

Powerline Adapter to generate a random private network name.

See “Using the Sync Buon” in next secon.

2� Create a customized private network name for your powerline

network by using the included Powerline Ulity. See “Using the

Powerline Ulity” on page 9”.

* If the Powerline Adapter sengs have been changed, the

adapter must be reset to the factory default sengs to be

recognized by Powerline Ulity.

Using the Sync buon

Change your default network name using the Sync buon

The physical Sync buon on the Powerline Adapter provides an easy

method of changing the network name� The Sync buon generates

a random network name for your powerline network. To create a

customized network name, see “Using the Powerline Ulity” on page

9�

Note: The default network name assigned to TRENDnet Powerline

Adapters is HomePlugAV. Before changing the default network name,

please make sure your Powerline Adapters are already installed and

connected using the default network name.

See “Installing Your Powerline Adapter” on page 5.

TPL-4052E User’s Guide Securing Your Powerline Network

Changing the network name and associang two Powerline

Adapters:

Note: Use the Sync buon procedure below if you are connecng

TRENDnet Powerline models TPL-401E, TPL-402E, TPL-405E , TPL-406E ,

TPL-407E or TPL-4052E.

1. Verify that all Powerline Adapters are already installed and

connected using the default network name, see “Installing Your

Powerline Adapter” on page 5.

Prepare your adapters:

2. On one of the connected Powerline Adapters, push and hold the

Sync buon for 15 seconds and then release it. All LEDs will turn o and

turn back on. This will erase the current network name assigned to the

rst Powerline Adapter.

Note: Once you have completed this step, the other Powerline Adapter

will no longer be able to communicate to this Powerline Adapter.

3. On the other Powerline Adapter, push and hold the Sync buon for

15 seconds then release it. All LEDs will turn o and turn back on. This

will erase the current network name assigned to the second Powerline

Adapter�

Start associaon:

4. Within 2 minutes, push and hold the Sync buon on the rst

Powerline Adapter for 2 seconds and then release it. The Power (PWR)

LED will start blinking. This will generate a random network name on

the rst Powerline Adapter.

5. Push and hold the Sync buon on the second Powerline Adapter

for 2 seconds and release it. The Power (PWR) LED will start blinking.

This will create a connecon between both Powerline Adapters using

Adding adapters using the Sync buon

If you have changed the default network name assigned to your

Powerline Adapters, addional adapters will not automacally connect

to your powerline network aer they are plugged into a wall power

outlet. You have to change the network name on addional Powerline

Adapter in order to join your exisng powerline network.

the new network name. All LEDs will turn o and turn back on and the

Powerline (PL) LED will turn on the when adapters are connected.

Andere Handbücher für TPL-4052E

Inhaltsverzeichnis

Andere TRENDnet Adapter Handbücher

TRENDnet

TRENDnet TE-PCIWplus Bedienungsanleitung

TRENDnet

TRENDnet TEW-644UB Bedienungsanleitung

TRENDnet

TRENDnet TEW-504UB Bedienungsanleitung

TRENDnet

TRENDnet TU2-ET100 Bedienungsanleitung

TRENDnet

TRENDnet TU-PS2 Bedienungsanleitung

TRENDnet

TRENDnet N600 Bedienungsanleitung

TRENDnet

TRENDnet TEW-445UB Bedienungsanleitung

TRENDnet

TRENDnet TEW-424UBK Bedienungsanleitung

TRENDnet

TRENDnet TU2-ETG Bedienungsanleitung

TRENDnet

TRENDnet TU3-HDMI Bedienungsanleitung

TRENDnet

TRENDnet TEW-229UB Bedienungsanleitung

TRENDnet

TRENDnet TU-ET100C - Bedienungsanleitung

TRENDnet

TRENDnet TE-16PNP Bedienungsanleitung

TRENDnet

TRENDnet TEW-623PI Bedienungsanleitung

TRENDnet

TRENDnet TEW-646UBH Bedienungsanleitung

TRENDnet

TRENDnet TBW-106UB Bedienungsanleitung

TRENDnet

TRENDnet TPL-307E Bedienungsanleitung

TRENDnet

TRENDnet TBW-107UB Bedienungsanleitung

TRENDnet

TRENDnet TEW-649UB - Mini Wireless N Speed USB 2.0... Bedienungsanleitung

TRENDnet

TRENDnet TEW-687GA 1.0R Bedienungsanleitung

TRENDnet

TRENDnet TU3-SA - Bedienungsanleitung

TRENDnet

TRENDnet TEW-429UB Bedienungsanleitung

TRENDnet

TRENDnet HotFlash TEW-429UF Bedienungsanleitung

TRENDnet

TRENDnet TEW-647GA Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung