TRENDnet TE-4010 Benutzerhandbuch

The information contains in this file is a startup guide for using the

TE-4010 with TRENDnet-View ver. 1.1.

Before you begin, make sure you have the following described environment:

o A PC with a network card installed and properly configured (IRQ and I/O

base address are set). We use TE-16XP/CT, but you can use any NE-2000

compatible cards.

o Windows ver. 3.1 is properly installed on the PC's hard drive.

o The PC is physically connected through a RJ-45 cable with TE-4010. It does

not matter which port is connected to.

o No network software (or driver) is loaded in either CONFIG.SYS and

AUTOEXEC.BAT files. A "clean boot" is preferred.

o Need two pieces of 25-pin serial cable and make the connection from hub's

OUT-OF-BAND management port -> serial cable -> null modem (provided with

TE-4010) -> serial cable -> PC's com1 or com2 port.

1. Start Windows 3.1.

2. Run TERMINAL program in the ACCESSORIES Group.

3. Make sure you have the following configurations:

o Full duplex

o Asynchronous communication

o Data: 8 bit

o Stop bits: 1

o Parity: none

o Baud rate: 9600

o COM1 or COM2 port

4. Press enter several time to go into the setup menu described on page 25

of the TE-4010's manual. Do not type any password.

5. Record the Hub IP Address. For example, 192.132.65.36. You need the IP

address for the TRENDnet-View software. We will use this number for this

example setup procedure.

6. Exit the setup program by pressing ESC key.

7. Exit the TERMINAL program without saving the current configuration. You

are now ready to load TRENDnet-View software. You can disconnect the

serial cable and the null modem.

8. Load TRENDnet-View disk in the floppy disk drive.

9. From program manager, select Run... in the File menu. A dialog box

appears.

10. Type "A:INSTALL" (do not type " ") and click the OK button.

11. In the TRENDnet-View Configuration dialog box, modify the following

information where appropriate:

o IP Address: 192.132.65.xxx xxx, leave it at default

o Gateway IP Address: 192.132.65.xxx xxx, leave it at default

o Subnet Mask: 255.255.255.0

o Network card: NE-2000

o IRQ Number: xx xx, setting for the network card

o I/O Port: xx xx, setting for the network card

12. Type in your password for any future modification of the above settings.

Do not exit from Windows 3.1.

13. Load the TE-4010 SNMP Module disk in the floppy disk drive. The diskette

is included with TE-4010.

14. From program manager, select Run... in the File menu. A dialog box

appears.

15. Type "A:INSTALL" (do not type " ") and click the OK button.

16. The installation is automatic. All files will be copied to where

TRENDnet-View is installed.

17. Exit Windows to DOS prompt.

18. Change directory to where TRENDnet-View is installed. For example,

CD\TRENDNET.

19. Run MANAGER.BAT and it will bring up Windows 3.1 automatically.

20. Run TRENDnet-View by double clicking the TRENDnet-View In-band icon in

TRENDnet-View group.

21. You must place a TE-4010 software module in order for TE-4010 to be seen

by the TRENDnet-View software. Click once on the leftmost button in

the speed button bar. A Device window appears on the upper right corner

on the screen. Move the mouse over the TE-4010 icon and click on it to

select.

22. Move your mouse to the client area of the TRENDnet-View, notice your

mouse cursor changes from a pointer to a stamp. Click the mouse once and

a TE-4010 icon is placed on the client area area. Assign a name for this

hub and supply the IP Address for this hub (For example, 192.132.65.36).

Ignore all other entries. Close the dialog box.

23. Wait couple seconds and the hub's name (beneath the icon) will turn from

blue to green. Double-click the icon and you will see TE-4010 panel on

the screen. You are ready to manage your TE-4010!

Our current version of TRENDnet-View does not run with any network software

installed on the same machine. For example, Windows for Workgroups 3.1/3.11,

Novell Netware 2.x, 3.x, 4.x,....etc. Therefore, do not load any network

software (or network driver) before go into TRENDnet-View.

You must run MANAGER.BAT from DOS prompt before go into TRENDnet-View

software (in-band or out-of-band). MANAGER.BAT loads Windows 3.1

automatically.

Inhaltsverzeichnis

Andere TRENDnet Netzwerk-Router Handbücher

TRENDnet

TRENDnet TEW-435BRM - 54MBPS 802.11G Adsl Firewall M Bedienungsanleitung

TRENDnet

TRENDnet TW100-BRF114U Bedienungsanleitung

TRENDnet

TRENDnet TEW-435BRM - 54MBPS 802.11G Adsl Firewall M Bedienungsanleitung

TRENDnet

TRENDnet TW100-BRF114 Bedienungsanleitung

TRENDnet

TRENDnet TW100-BRF104 Bedienungsanleitung

TRENDnet

TRENDnet TI-G80 Bedienungsanleitung

TRENDnet

TRENDnet TW100-BRV324 Bedienungsanleitung

TRENDnet

TRENDnet TEW-435BRM - 54MBPS 802.11G Adsl Firewall M Bedienungsanleitung

TRENDnet

TRENDnet TW100-BRV304 - Advanced VPN Firewall Router Bedienungsanleitung

TRENDnet

TRENDnet TW100-W2plus Bedienungsanleitung

TRENDnet

TRENDnet TE100-S32 Handbuch

TRENDnet

TRENDnet TPL-302E2K - Powerline AV Fast EN Adapter Bedienungsanleitung

TRENDnet

TRENDnet TEW-723BRM Bedienungsanleitung

TRENDnet

TRENDnet TEW-671BR Bedienungsanleitung

TRENDnet

TRENDnet TEG-448WS - Switch Bedienungsanleitung

TRENDnet

TRENDnet TVP-224HR Bedienungsanleitung

TRENDnet

TRENDnet AC3200 Bedienungsanleitung

TRENDnet

TRENDnet TW-H6W1IR Bedienungsanleitung

TRENDnet

TRENDnet TEW 632BRP - Wireless Router Bedienungsanleitung

TRENDnet

TRENDnet TEW-452BRP - 108Mbps Wireless Super G Broadband... Bedienungsanleitung

TRENDnet

TRENDnet TE100-S5Pplus Kurzanleitung

TRENDnet

TRENDnet TW100-BRF214 Bedienungsanleitung

TRENDnet

TRENDnet THA?101 Bedienungsanleitung

TRENDnet

TRENDnet TEW-827DRU Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise