TRENDnet TV-IP300W Bedienungsanleitung
Copyright ©2004. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TV-IP300W
Version 1.11.05
Advanced Day/Night Internet Camera Server
Quick Installation Guide
Guide d'installation rapide pour le
Internet Caméra Serveur Avancée Jour et Nuit
Anleitung zur Schnellinstallation des
Infrarot Nachtsicht Farb IP Kamera Server
Guía de Instalación Rápida para
Servidor Avanzado De la Cámara fotográfica Del Internet De Dia/Noche
Table of Contents
English ......................................................................................................
Troubleshooting ........................................................................................
1
1
2
4
5
7
1. Prepare for Installation ......................................................................
2. Install Hardware ................................................................................
3. Configure the Internet Camera ..........................................................
4. Using the Internet Camera Wirelessly ...............................................
Thank you for purchasing the TV-IP300W. This Internet Camera will allow you
to view live images from internal and external networks.
This guide will help you set up and configure your Internet Camera. Following
the installation instructions should be quick and easy. If you run into problems,
please refer to the Troubleshooting section or the more detailed installation
procedures on the CD User's Guide. If you need further technical support,
please visit www.trendnet.com or call our technical support department by
phone.
Verify Package Contents
Please make sure you have everything in the box:
1
1. Prepare for Installation
English QIG
English
System Requirement
1. 10/100Mbps Ethernet
2. CD-ROM Drive
3. CPU: Intel Pentium III 350MHz or above
4. Memory: 128MB or above
5. Web Browser: Microsoft Internet Explorer 5.0 or above
6. VGA Resolution: 800 x 600 or above
TV-IP300W
CD-ROM Quick Installation Guide
AC Power Adapter Metal Stand
Copyright ©2004. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TV-IP300W
Version 1.11.05
Advanced Day/Night Internet Camera Server
Quick Installation Guide
Guide d'installation rapide pour le
Internet Caméra Serveur Avancée Jour et Nuit
Anleitung zur Schnellinstallation des
Infrarot Nachtsicht Farb IP Kamera Server
Guía de Instalación Rápida para
Servidor Avanzado De la Cámara fotográfica Del Internet De Dia/Noche
2
2. Install Hardware
1. Position the metal stand, and mount the Internet Camera to the stand.
2. Connect the RJ-45 network cable to the Internet Camera then connect the
other end of the network cable to a switch or hub.
3. Connect the power adapter to the Internet Camera. Make sure to use the
power adapter supplied with the Internet Camera.
English
TV-IP300W
Note: Using a different power adapter may damage the unit.
32
1
3English
Special I/O Ports Features
1. I/O Connector
The Internet Camera provides the I/O connectors on the rear panel, which
provide the physical interface to send and receive digital signals to variety of
external alarm devices.
2. DIP Switch
AES/AI Switch: When using the Auto Iris Lens, please switch to AI position
Flicker less/Off: If the power frequency used (in NTSC area) is 50Hz, please
switch to Flicker less position.
3. Iris Level
This is used only when the DC-Iris lens is connected to the camera.
4. Reset Button
This resets all the settings in the camera to default factory settings.
Power
Reset switch
RJ-45
Connector
Iris level
I/O connector
DIP switch
4
1. Open Internet Browser Window and enter <http://192.168.0.30> (camera's
default IP address)
2. Click on System Administration to access the configuration page.
3. Enter an IP address, Subnet mask, and Default gateway that corresponds
with your existing network for the camera. Then click on Save button to keep
the changes.
English
3. Configure the Internet Camera
Note: The PC's IP (Example 192.168.0.50) address must correspond
with the Internet Camera's IP address (Default IP: 192.168.0.30) in the
same segment for the two devices to communicate.
Note: If you need to access the configuration remotely, it is
recommended to enter a static IP address and the Internet DNS IP
address.
5English
4. Using the Internet Camera Wirelessly
1. Scroll down in the System Administration configuration page until you see
the Wireless Interface heading.
2. Type in the same SSID of your wireless Access Point or Router into the
ESSID field. Set Wireless Mode to Infrastructure and make sure that the
channel is the same as your wireless Access Point or Router. If your
wireless Access Point or Router has WEP encryption enabled, select Data
encryption and make sure that the Auth mode, Key length, Key format,
and Default key are the same as your wireless Access Point or Router.
6English
3. Scroll down to the bottom of the page and Click Save.
4. Disconnect the CAT5 cable and the power adapter connector from the TV-
IP300W.
5. Reconnect the power adapter connector to the TV-IP300W. Allow 5-10
seconds for the TV-IP300W and the wireless Access Point to communicate
wirelessly. Then type the IP Address that you assigned to the TV-IP300W in
your web browser for verification.
7
Q1.
A1.
Q2.
A2.
Q3.
A3.
Q4.
A4.
The image is blurry, how do I fix this?
You can adjust the Internet Camera's focus by rotating the lens.
Can I replace the camera lens?
The Internet Camera's Lens is replaceable with a standard CS-Mount
type lens.
How do I view the Internet Camera's live images within my Local
Network?
Open a web browser (Internet Explorer or Netscape), type your
Wireless Internet Camera's IP address (i.e.: 192.168.0.30) in the Address
bar, and then hit the Enter key. The Welcome page of the Internet Camera
will appear.
When I enter the IP address of the camera, the image does not load,
why?
Please make sure all the Active X features are enabled for your
Internet Explorer.
1. Go to Tool (on the Tool bar) > Internet options > Security
Troubleshooting
8
2. Click on Custom Level and make sure all ActiveX controls are set to
"Enable" and click OK.
3. Once you save the settings, the browser will load again and the image
should appear.
Andere Handbücher für TV-IP300W
1
Andere TRENDnet Sicherheitskamera Handbücher
TRENDnet
TRENDnet TV-IR500 Bedienungsanleitung
TRENDnet
TRENDnet 15-AH28B Bedienungsanleitung
TRENDnet
TRENDnet TV-IP262PI Bedienungsanleitung
TRENDnet
TRENDnet TV-IP440PI Bedienungsanleitung
TRENDnet
TRENDnet TV-IP743SIC Bedienungsanleitung
TRENDnet
TRENDnet TV-IP522P Bedienungsanleitung
TRENDnet
TRENDnet TV-IP551W Bedienungsanleitung
TRENDnet
TRENDnet TV-IP312PI Bedienungsanleitung
TRENDnet
TRENDnet TV-IP201 Bedienungsanleitung
TRENDnet
TRENDnet TV-IP400 Bedienungsanleitung
TRENDnet
TRENDnet TV-IP512WN - ProView Wireless N Internet Surveillance... Bedienungsanleitung
TRENDnet
TRENDnet TV-IP612WN Bedienungsanleitung
TRENDnet
TRENDnet TV-IP300 Bedienungsanleitung
TRENDnet
TRENDnet TV-IP751WIC Bedienungsanleitung
TRENDnet
TRENDnet TV-IP252P - SecurView PoE Dome Internet Camera... Bedienungsanleitung
TRENDnet
TRENDnet TV-IP301 - ProView Advanced Day/Night Internet Surveillance... Bedienungsanleitung
TRENDnet
TRENDnet TV-IP422WN Bedienungsanleitung
TRENDnet
TRENDnet TV-IP341PI Bedienungsanleitung
TRENDnet
TRENDnet TV-IP325PI Bedienungsanleitung
TRENDnet
TRENDnet TV-IP110WN Bedienungsanleitung
