TRENDnet TE100-S800i Bedienungsanleitung

1. Introduction

The 8 10/100Base-TX Management Switch is a compact switch that is ideal

for SOHO (Small Office or Home Office) networks. It provides wired-speeds,

Fast Ethernet switching, and store-and-forward switching to attain

high-performance at low-cost connections. It can also auto-learn and store

source addresses on an 8K-entry MAC address table.

The Switch provides 8 auto-sensing 10/100 Mbps RJ-45 Ethernet ports,

supporting Auto-MDIX function for each port. [In general, MDI means

connecting to another Hub or Switch while MDIX means connecting to a

workstation or PC. Therefore, Auto-MDIX means you can use any cable,

straight-through or cross-over, to connect to another Switch or workstation. ]

With its built-in Web-based Utility, managing and configuring the 8

10/100Base-TX Management Switch becomes easier. From cabinet

management to port-level control and monitoring, you can visually configure

and manage your network via Web Browser. Just click your mouse instead

of typing command strings. If you prefer using a Command Line Interface,

the 8 10/100Base-TX Management Switch can also be managed via Telnet,

Console, or SNMP Management.

Features

8 10/100BASE-TX intelligent switch

Switch fabric up to 3.8Gbps

Layer 2 Web-based management switch

IGMP support for Multi-media application

Port Mirroring supported

Spanning Tree, SNMP, RMON supported

Support Port-based VLAN

IEEE802 .1Q VLAN, GVRP supported

Support Class of Service

Broadcast Storm filter supported

Support Port Security

IEEE802.3ad Port trunk with LACP supported

Software Features

SNMP

RFC 1157 SNMP, RFC 1213 MIB II, Bridge MIB, RFC 1643

Ethernet Like, RFC 1493 Bridge MIB, RFC 1757 RMON1,

LANTECH Enterprise MIB, RFC 1215 Trap,

Management

Web management (IE)

RS-232 console management (Rear side)

Telnet

Trunk

IEEE 802.3ad Trunk with LACP for load distribution control

and fail over recovery

Up to 4 ports per group, max 4 Groups

Class of Service Global system supports 2 queues for Hi and Low priority

QoS Global System support 8 levels of priority and mapping to

Hi/Low priority queue for Class of Service

VLAN

Port based VLAN, 802.1Q Tag VLAN, Protocol Type VLAN,

GVRP support

VLAN ID up to 4094, VLANs up to 256 groups

IP Multicast

Support IGMP Snooping, supports 256 groups.

Support 2 types of Query mode for Enable/Disable or Auto

Query

Filter Database Support port static MAC address lock, MAC Filter, Port

Security

Port Mirror Use this feature to analyze port traffic. It supports a

maximum of 8 ports.

Broadcast

Control None, 5%, 10%, 15%, 20%, 25%

Spanning Tree IEEE802.1d support

RFC Standard

RFC 768 UDP, RFC 783 TFTP, RFC 791 IP, RFC792

ICMP, RFC 854 TELNET Server/Client, RFC 1112 IGMP,

RFC 2068 HTTP,

PackageContents

Unpack the contents of the 8 10/100Base-TX Management Switch and

verify them against the checklist below.

8 10/100Base-TX Management Switch

Power Cord

Four Rubber Feet

RS-232 cable

User Guide

8 10/100Base-TX Management Switch Power Cord

Rubber Feet RS-232 cable

Figure 1-2. Package Contents

Compare the contents of your 8 10/100Base-TX Management Switch

package with the checklist above. IF any item is missing or damaged,

please contact your local dealer for service.

ManagementMethods

The 8 10/100Base-TX Management Switch series supports the following

management methods:

Console and Telnet Management

Web-based Management

SNMP Network Management

Console and Telnet Management

Console Management is done through the RS-232 Console Port. Using this

method to manage the 8 10/100Base-TX Management Switch requires a

direct connection between the PC and the 8 10/100Base-TX Management

Switch. Telnet management is done over the network. Once the 8

10/100Base-TX Management Switch is on the network, you can use Telnet

to Log in and change the Switch’s configuration.

Web-based Management

The Switch provides an embedded HTML web site residing in flash memory.

It offers advanced management features that allow a user to manage the 8

10/100Base-TX Management Switch from anywhere on the network by

using a standard browser, such as Microsoft Internet Explorer.

SNMP Network Management

SNMP (Simple Network Management Protocol) provides a means to

monitor and control a network device, and to manage configuration, statistic

collection, performance, and security.

2. Hardware Description

This section mainly describes the hardware of the 8 10/100Base-TX

Management Switch.

FrontPanel

The Front Panel of the 8 10/100Base-TX Management Switch consist of 8

auto-sensing 10/100Mbps Ethernet RJ-45 ports (automatic MDI/MDIX).

The LED indicators are also located on the frond panel of the switch.

Figure 2-1. The Front Panel of the 8 10/100Base-TX Management Switch

RJ-45 Ports (Auto-MDIX): Eight 10/100Mbps ports can automatically

sense 10Base-T or 100Base-TX connections.

[In general, MDI means connecting to another Hub or Switch while

MDIX means connecting to a workstation or PC. Therefore, Auto-MDIX

means you can use any cable, straight-through or cross-over, to

connect to another Switch or workstation. ]

LEDIndicators

There are three LED-Indicators (100M, LNK/ACT, FDX/COL) for each UTP

port. The following table provides a description for each LED status and

meaning. They provide a real-time indication of systematic operation status.

Figure 2-2. LED Indicators

LED Status Color Description

Power On Green Power On

On Green

The port is operating at the

speed of 100Mbps.

100M

Off In 10Mbps mode or no

device attached

On Green

The port is successfully

connecting with the device.

Blinks Green The port is receiving or

transmitting data.

LNK /ACT

Off No device attached.

On Orange

The port is operating in

Full-duplex mode.

Blinks Orange

Collision of Packets occurs

in the port.

FDX /COL

Off Half-duplex mode or no

device attached.

Table 2-1. The description of LED Indicator

RearPanel

The Console port and 3-pronged power plug are located at the Rear Panel

of the 8 10/100Base-TX Management Switch as shown in Figure 2-3. The

Switch will work with the AC in the range of 100-240V AC, 50-60Hz.

Figure 2-3 The Rear Panel of the 8 10/100Base-TX Management Switch

Console Port: Console management can be done through the Console

Port. It requires a direct connection between the Switch and an end station

(PC) via a RS-232 cable.

DesktopInstallation

Set the switch on a sufficiently large flat space with a power outlet nearby.

The surface where you put your Switch should be clean, smooth, level, and

sturdy. Make sure there is enough clearance around the Switch to

allow attachment of cables, power cord and air circulation.

Attaching Rubber Feet

1. Make sure that the mounting surface on the bottom of the Switch is

grease and dust free.

2. Remove the adhesive backing from your Rubber Feet.

3. Apply the Rubber Feet to each corner on the bottom of the Switch.

These footpads help prevent shock/vibration.

Figure 2-4. Attaching Rubber Feet to each corner on the bottom of the Switch

Power On

Connect the power cord to the power socket on the rear panel of the Switch.

The other side of power cord connects to the power outlet. Check the power

indicator on the front panel to see if power is properly supplied.

Andere Handbücher für TE100-S800i

Inhaltsverzeichnis

Andere TRENDnet Schalten Handbücher

TRENDnet

TRENDnet TK-208K Bedienungsanleitung

TRENDnet

TRENDnet TPE-S80 Bedienungsanleitung

TRENDnet

TRENDnet TPE-224WS - Web Smart PoE Switch Bedienungsanleitung

TRENDnet

TRENDnet NWay Bedienungsanleitung

TRENDnet

TRENDnet TE-500 Bedienungsanleitung

TRENDnet

TRENDnet TE100-S1212 Bedienungsanleitung

TRENDnet

TRENDnet TEG-S50G Bedienungsanleitung

TRENDnet

TRENDnet TK-1602R Bedienungsanleitung

TRENDnet

TRENDnet TEG-S081Fi Handbuch

TRENDnet

TRENDnet TPE-3012L Bedienungsanleitung

TRENDnet

TRENDnet TK-1603R Bedienungsanleitung

TRENDnet

TRENDnet TE100-S1616V Bedienungsanleitung

TRENDnet

TRENDnet TE100-S1616V Bedienungsanleitung

TRENDnet

TRENDnet TEG-224WS - DATA SHEETS Bedienungsanleitung

TRENDnet

TRENDnet TPE-TG50ES Bedienungsanleitung

TRENDnet

TRENDnet TEG-S240TX - DATA SHEETS Bedienungsanleitung

TRENDnet

TRENDnet TE100-SK1 Bedienungsanleitung

TRENDnet

TRENDnet TK-205K - PS/2 KVM Switch Bedienungsanleitung

TRENDnet

TRENDnet TK-423K - USB/PS/2 KVM Switch Bedienungsanleitung

TRENDnet

TRENDnet TEG-S240TX - DATA SHEETS Bedienungsanleitung

TRENDnet

TRENDnet TE100-S32plus Bedienungsanleitung

TRENDnet

TRENDnet TEG-S2400I - DATA SHEETS Installations- und Betriebshandbuch

TRENDnet

TRENDnet TPE-T88G Bedienungsanleitung

TRENDnet

TRENDnet TE100-DX8E Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung