TrickleStar TS1921 Bedienungsanleitung

Installation Guide

TS1921 Occupancy Sensor

Table of Contents

1 What is in the box? 4

2 Sensor Overview 5

3 Pairing the Sensor 6

4 Mounting the Sensor on the wall 10

5 Placing the Sensor on a at surface 11

6 Ready for use 12

7 Changing Occupancy Detection settings on the Portal 13

8 Occupancy Detection 14

9 Connectivity 19

10 Specications 20

11 Enviromental-Friendly Features 22

12 Replacing the battery 23

13 Troubleshooting 24

Welcome!

Thank you for choosing the TrickleStar TS1921 Occupancy Sensor.

This Occupancy Sensor is an accessory for the TrickleStar Wi-Fi Smart

Thermostat. The Sensor helps the Thermostat to maximize comfort to your

room as the sensor can detect occupancy as well as measure the temperature

in the room. Maximum 6 sensors can be connected to the thermostat via

bluetooth.

This Installation Guide describes how to install the Sensor and pair it to a

TrickleStar Wi-Fi Smart Thermostat.

If you have any inquiries about TrickleStar products or need technical support,

visit our website for tutorials, videos and Frequently Asked Questions (FAQ).

You can also contact us by email or phone.

Instruction Videos

If you want to see the Installation Instructions

as videos, visit our YouTube channel:

https://www.youtube.com/user/TrickleStarUS/

Website: www.tricklestar.com

Email: customer.service@tricklestar.com

Toll Free: 1-888-700-1098

Preparation

What is in the box?

Occupancy

Sensor

QR code sheet Lithium cell battery

(CR2477X x 1)

Stand Double-sided

adhesive

Sensor Overview

Fresnel Lens

Stand

Battery Cover

Top View

Bottom View

LED Indicator

Battery Cover

Double-sided

adhesive

(for wall mount)

Slot (for stand)

Stand (detachable)

Pairing

Button

Pairing the sensor

Step 1: Pull the plastic tag

To power up the Sensor, pull out the plastic tag from the Sensor gently.

When the Sensor is powered up, it enters Pairing mode automatically. The

LED starts blinking and continues blinking up to eight minutes.

Plastic tag

If the LED does not blink after the Sensor is powered up or after battery

insertion or the Sensor exits Pairing mode after eight minutes, hold the Pairing

Button for 2 seconds to re-initiate pairing to the thermostat. The sensor will

enter Pairing mode again and broadcast itself for 8 minutes for thermostat

scanning. LED will blink briefly in the mode.

Step 2: Add Occupancy Sensor to the system

at: portal.tricklestar.com You can also use the QR

code here.

At Dashboard screen, select Devices, then click on your Thermostat Name

to enter Thermostat page.

Select Sensors on the left panel, then click on “+” to add a new sensor.

4. Enter the name for your sensor.

5. Press Next once your sensor LED is blinking to complete the pairing process.

This will initiate a scan function and Thermostat will scan for sensors in range.

Sensors that are detected will be listed by their MAC addresses. User can

select from the list if there is more than one sensor to be paired and add the

sensors. Note: It may take up to 30 seconds to detect and pair a new sensor.

6. Once your sensor is successfully added, the Connection Status, Temperature

and Occupancy State will be “Not Used”. Wait for 1-2 minutes then click on

the "Refresh Sensor Data" button to update the sensor readings.

If the LED does not blink after the Sensor is powered up or after battery

insertion or the Sensor exits Pairing mode after eight minutes, hold the Pairing

Button for 2 seconds to re-initiate pairing to the thermostat. The sensor will

enter Pairing mode again and broadcast itself for 8 minutes for thermostat

scanning. LED will blink briefly in the mode.

Step 2: Add Occupancy Sensor to the system

1. Log in to your TrickleStar Portal account

at: portal.tricklestar.com You can also use the QR

code here.

2. At Dashboard screen, select Devices, then click on your Thermostat Name

to enter Thermostat page.

3. Select Sensors on the left panel, then click on “+” to add a new sensor.

4. Enter the name for your sensor.

5. Press Next once your sensor LED is blinking to complete the pairing process.

This will initiate a scan function and Thermostat will scan for sensors in range.

Sensors that are detected will be listed by their MAC addresses. User can

select from the list if there is more than one sensor to be paired and add the

sensors. Note: It may take up to 30 seconds to detect and pair a new sensor.

Once your sensor is successfully added, the Connection Status, Temperature

and Occupancy State will be “Not Used”. Wait for 1-2 minutes then click on

the "Refresh Sensor Data" button to update the sensor readings.

If pairing is successful, the LED will blink twice. Then, the Bluetooth indicator

appears on the Thermostat display.

If pairing is unsuccessful or time-out after 8 minutes, the LED will stop

blinking and the Sensor will go into standby mode. In Standby mode, the

connection between the sensor and the thermostat is not set up. All the

sensor circuits will be shut down to save power. Hold the Pairing Button for 2

seconds to initiate the Pairing mode again.

Note: If the sensor is previously registered, it will be added to the thermostat

network automatically in Pairing mode. The sensor LED will blink twice, then

Pairing mode finishes, and change to Normal mode. If disconnected, the

sensor will change to Pairing mode automatically and try to reconnect with

the thermostat. User can also press the pairing button to restart the sensor in

Pairing mode.

Mounting the Sensor on the wall

Before you mount the Sensor on the wall, be sure to check that:

•

The sensor is connected to the Thermostat.

•

The sensor is mounted away from direct heating or cooling sources, such

as a fireplace or an air ventilator.

Attach the double-sided adhesive to the Sensor. Then, mount the Sensor at a

height of approximately 5 ft. (1.5 m) on the wall.

5 ft.

(1.5 m)

Andere Handbücher für TS1921

Inhaltsverzeichnis

Andere TrickleStar Zubehör Handbücher

TrickleStar

TrickleStar TS1914 Bedienungsanleitung

TrickleStar

TrickleStar SENSORCLICK 188LV-US-4 Series Bedienungsanleitung

TrickleStar

TrickleStar TS1810 Bedienungsanleitung

TrickleStar

TrickleStar TS1921 Bedienungsanleitung

TrickleStar

TrickleStar SENSORCLICK 188LV-TFS-3F Bedienungsanleitung

TrickleStar

TrickleStar SENSORCLICK 188LV-TFS-3F Bedienungsanleitung

TrickleStar

TrickleStar Advanced PowerStrip+ Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung