Troy Built Models SPITFIRE MK.XIV Bedienungsanleitung

120mm

Top view

Side View

40mm

RUDDER

Air tank

Switch

Air inlet

3-way

pressure inlet

3-way

pressure inlet

3-way

pressure inlet

The status when the

gear up

Pull out length of 8mm

to make gear down

Air valve Air valve

Make sure to assemble retracts as instructed below.

Two wheel retract system

Quick release connector

Pressure reduction inlet

Strut

3-way pressure inlet 3

Pressure reduction inlet 1

Air tank

Air inlet

Air line (3000mm)

Quick release connector

Strut

( 90 )

Switch

Clevis

Rod (2X300mm)

Retainer

TP Screw(2x14mm) 2

Ø1.7mm

Ø0.2mm

Pleas notice the inner diameter

of eachside the pressure reduction inlet.

Please insure the sealing of theretract

system before flight .

Adjustment. The centre of the Gravity.

Specifications:

Wing Span: 1840mm (72 ½” Inches)

Length: 1625mm(64in)

Wing Area: 946sq.in

Wing loading: 33oz/sq.ft

Flying weight: 13 Ibs

Power: ..91 _ 1.20 Two Stroke or .90 - .120 Four Stroke

Radio: 6 Channel w/8 Standard Servos

SPITFIRE MK.XIV\XIX

SAFETY PRECAUTIONS

INSTRUCTION MANUAL

First-time builders should seek advice from people having building

experience.If misused or abused,it can cause serious bodily injury

and damage to property.

Fly only in open areas and preferably at a dedicated R/C flying site.

We suggest having a qualified instructor carefully inspect your

airplane before its first flight.Please carefully read and follow all

instructions included with this airplane,your radio control system

and any other components purchased separately.

(The people under 18 years old is forbidden from flying this model)

This R/C airplane is not a toy!

:4-cycle-120

15″X73.7 in Spinner

6 channel radio for aiplane is highly recommended for this model.

Optional parts: rubber wheel with metal hub,

oleo struts and retracts system.

TP Screw (3x20mm)

Wooden Block

TP Screw (2.6x14mm)

Collar (5mm)

Wooden supporter

Collar (5mm)

Washer (3x6mm)

Wooden Block(43x28x26mm)

Gear door

Collar (5mm)

Wheel (100mm)

Landing gear(5mm) 2

TP Screw (3x20mm )

Landing gear straps

TP Screw (2.6x14mm)

Washer (3x6mm)

Wooden Block(25x15x13mm)

Assemble the wheel and gear door to landing gear.

30mm

40mm

AILERON

FLAP

Side View

Top view

Position for

right diagram.

ELEVATOR

Side View

30mm

Centre of Gravity.

Adjustment.

Epoxy the landing gear to the wing steadily.

Adjustment.

AILERON FLAP

260mm

115mm

TP Screw (2.3x8mm)

1.5mm

TP Screw (2.3x8mm)

Epoxy plastic part underneath the wing.

Accessory list for the coming installation steps.

Epoxy plies inside the fuselage under the cowing and

mount the cowing with TP screw as illustration.

TP Screw (2.3x8mm)

Ply (15x15x3mm) 5

1.5mm

TP Screw (2.3x8mm)

Ply (15x15x3mm) 8

1.5mm

TP Screw (2.3x8mm)

Deconation

Epoxy plies to relevant position inside the fuselage as

below for assembling the cowling.

Epoxy plies inside the fuselage under the cowing and

mount the cowing with TP screw as illustration.

Cut off the surplus part of pvc parts.

Cut off the surplus part from the cowling,exhausts and

canopy carefully.

Epoxy the exhaust the the cowling as figure. Epoxy the deconation to appropriate position

under the wing.

Make sure hinges are

mounted in the same line.

1mm

Aileron

Trailing

edge

Make sure they are in

the right position while

installing.

Pin hinge(24x24mm)

Clevis

Rod (2x300mm)

Retainer

TP Screw (2.3x12mm)

Wooden Block(20x20x8mm)

Servo tray(68.5x56.5x2mm)

Pin hinge(24x24mm)

Screw (3x35mm)

Washer(3x15mm)

Lock Nut (3mm )

Clevis

Retainer

Rod (2x300mm)

Screw (2x10mm)

Securely glue together. If coming off during flights, you 'll

lose control of your airplane which leads to accidents!

Install the servo as the illustration below

Install the nylon control horn and connect the linkage.

Apply instant CA glue to aileron and pin hinge.

Keep some space about 1mm width between

aileron and trailing edge.

Assemble the aileron to main wing with instant type CA glue. Be careful

to ensure the moving parts of the hinges are able to move freely.

Accessory list for the coming installation steps.

Clevis

Rod (2x300mm)

Retainer

TP Screw (2.3x12mm)

Wooden Block(20x20x8mm)

Servo tray(68.5x56.5x2mm)

Pin hinge(24x24mm)

Screw (3x35mm)

Washer(3x15mm)

Lock Nut (3mm )

1.5mm

TP Screw (2.3x12mm)

3mm

Rod (2x300mm)

Clevis

Washer(3x15mm)

Washer

Lock Nut (3mm )

Screw (3x35mm)

Screw (2x10mm)

Pin hinge(24x24mm)

Keep some space about 1mm width between

trailing edge and flap.

Securely glue together. If coming off during flights, you 'll

lose control of your airplane which leads to accidents!

Flap

1mm

Make sure they are in

the right position while

installing.

Trailing

edge

Secure the servo.Install the nylon control horn

and connect the linkage.

The position of the control horn in the aileron. Epoxy the pin hinges to the flap.

Epoxy the flaps to the wings as illustration.

Accessory list for the coming installation steps.

Clevis

Copper joiner

Screw (2x10mm)

Nut (2mm )

Washer(2x5mm)

Clevis 1

Rod (2x300mm) 1

Retainer

Ring

Air tank

Switch

Clevis

Copper joiner

Screw (2x10mm)

Nut (2mm )

Washer(2x5mm)

Steel wire

Copper joiner

Lock Nut (2mm )

Screw (2x10mm)

Ball joint

Washer(2x5mm)

Add a rubber ring to the

clevis for insuring safety

Pvc part

Deconation

Install the servo of swith.

Install the servo.

switch servo

Throttle servo

Rudder servo

Elevator servo

The servos installation finished sketch map.

Assemble the receiver and the battery to appropriate

in the fuselage.

Ply(15x15x2mm)

TP Screw (2.3x8mm)

Canopy

Pvc part

Accessory list for the coming installation steps.

2.5mm

Tail wheel

Washer(3x15mm)

Screw (3x65mm)

Lock Nut (3mm )

Clevis

Aluminum tube

Steel wire

Steel wire (0.5x1200mm)

Clevis

Retainer

Washer(3x15mm)

Lock Nut (3mm )

Screw (3x65mm)

Copper joiner

The sketch map after the rudder shaft assemble finished.

The sketch map for the linkage of the rudder

and the tail wheel and elevator in the fuselage.

3mm

30mm

Retainer

TP Screw (2.3x8mm)

Ply (15x15x3mm) 8

Collar

Tail landing gear

Drill holes to the relevant position in the tailing edge

and epoxy the rudder to them.

Drill a small hole to appropriate possition in the

fuselage for installing the plastical tube.

15mm

45mm

Plastical tube(3x50mm)

Drill a hole to appropriate position in the

rudder as illustration.

Epoxy plies to appropriate position in the fuselage and

assemble the tail gear cover with screw.

Then assemble the wheel as illustration.

49 52

1.5mm

TP Screw (2.3x12mm)

Rod (2x300mm)

Clevis

Washer(3x15mm)

Washer

Lock Nut (3mm )

Screw (3x35mm)

Screw (2x10mm)

3mm

Wood dowel (6x50mm)

Blind Nut (6mm)

Screw (6x50mm)

Gear door

Wheel (100mm)

TP Screw (3x20mm)

Washer (3x6mm)

Wooden Block(25x15x13mm)

PVC part

Retracts strut

LockNut(4mm)

Wooden Block

Note:rubber wheels oleo struts

and retracts are optional.

5mm

Cut away the surplus parts of plastic cover

carefully along the shaded line.

Main wing joiner

Rib template (3mm ply)

PVC part

Wood dowel (4x30mm)

Reinforcement Plate 1

LockNut(4mm)

Mount the gear door and the wheel to the retract.

Cut away the shaded portion for assembling

the gear house.

Secure the servo.Install the nylon control horn

and connect the linkage.

The position of the control horn for flap in the wing.

Accessory list for the coming installation steps.

TP Screw (2.3x12mm)

C = C"

side wing centre wing

4mm

Wood dowel (4x30mm)

Rib template (3mm ply)

Main wing joiner 1

330mm

219mm

4mm

The sketch maps when the retract up and down.

Epoxy the gear house to the relevant position.

Assemble the retracts to the appropriate position

in the gear house.

Epoxy the PVC decoration parts to the appropriate

position on the wing as illustration.

According to the rib template drill holes to one wing

root and epoxy wood dowel in them.

According to the rib template drill holes to anther wing

root and connect the wings with main wing joiner.

16 19

Plastical tube(3x50mm)

Nose arm(3mm)

Collar (3mm) 2

Tail landing gear(3mm)

Tail wheel (45mm)

Retainer

Rod (2X257mm) 1

TP Screw(3x20mm)

Washer (3x6mm)

Steel wire (0.5x1200mm)

Clevis

Washer(3x15mm)

Lock Nut (3mm )

Screw (3x65mm)

Copper joiner

Collar

Tail landing gear

Collar

2.5mm

Pin hinge(2.5x48mm)

Make sure hinges are

mounted in the same line.

42mm 84mm 80mm

Ply (6mm)

1.8mm

TP Screw(3x20mm)

Washer (3x6mm)

Ply (3mm) 2

suggest drilling a hole here for

assembling wheel steeling

mount

25mm

Pin hinge(2.5x48mm)

The sketch map when tail wheel assemble completion.

Drill holes to appropriate position in the rudder and epoxy

the ping hinges in them

1mm

Rudder

Tailing

edge

Cut away the rubber tube when

the epoxy glue dried.

Make sure they are in

the right position while

installing.

Keep some space about 1mm width between

the tailing edge and the rudder.

The sketch map when assemble the tail landing

gear to the wheel steeling mount.

The sketch map of assembling the wheel steeling

mount to appropriate position in the fuselage.

Accessory list for the coming installation steps.

Fuel supply line

Fuel spray line

Air pressure line

Linkage Stopper

Washer (2mm)

Nut (2mm)

Set screw (3x4mm)

Washer (

2mm

)

Set screw (3x4mm)

Set Screw (3x4mm)

Set Screw (2mm)

Rod (2x400mm)

Set Screw (2mm)

Washer (2mm)

Linkage Stopper

Washer (4x8mm)

Set Screw (3x4mm)

Assemble the accelerateor push rod to the engine. Mount the fuel tank to the fuselage.

Install the servo.

Assemble the throttle servo to appropriate

position in the fuselage.

Assembly of the fuel tank.

Engine installation finished sketch map.

39 42

Accessory list for the coming installation steps.

100mm

R10

40mm

Wood dowel (6x50mm)

Assemble the wings to the fuselage with screw

and blind nut as below.

Drill holes to relevant position in the fuselage.

6mm

80mm

AA'

Make sure to glue securely.

If not properly glued, a failure in flight may occur.

Temporarily fasten down the main wing and

check its correct position.

Securely glue together.If coming off during flights,

you'll lose control of your airplane which leads

to accidents!

A=A'

B=B'

Blind Nut (6mm)

Screw(6x50mm)

Reinforcement Plate 1

6.2mm

Blind Nut

Steel wire (0.5x3000mm)

U-style wire (25x5mm)

Pin hinge(24x24mm) 6

TP Screw (2.3x12mm)

Pin hinge(2.5x48mm)

Wood dowel (4x30mm)

Rib template (2mm ply)

Stab joiner (12x210mm)

Screw(6x50mm)

80mm

6mm

220mm

Trim holes in the appropriate position for draging

the air tubes and servo lines out.

Drill holes to appropriate postition in the wing leader

and epoxy wood dowels in them as illustration.

The sketch map should be when the stabilizer

assembly completion.

Accessory list for the coming installation steps.

Make sure hinges are

mounted in the same line.

Pin hinge(24x24mm)

3mm

1mm

Elevator

Tailing

edge

Make sure they are in

the right position while

installing.

Steel wire (0.5x3000mm)

U-style wire (3mm)

4mm

Rib template (3mm ply)

2x7mm

4mm

Wood dowel (4x30mm)

Securely glue together. If coming off during flights, you 'll

lose control of your airplane which leads to accidents!

Stab joiner (12x210mm)

Apply instant type CA glue to elevator and pin hinge.

Keep some space about 1mm width between

elevator and tailing edge.

Drill holes to appropriate position in the stabilizer and

epoxy it to the fuselage as below.

According to the rib templete drill holes to appropriate

position in the tail fuselage.

According to the rib templete drill holes one the

stabilizer root and epoxy wood dowel in them.

Set the U-style wire through the enlarged hole as below.

3mm

Securely glue together. If coming off during flights, you 'll

lose control of your airplane which leads to accidents!

Glue the elevator to the stabilizer by CA and epoxy.

3mm

Securely glue together. If coming off during flights, you 'll

lose control of your airplane which leads to accidents!

Glue the elevator to the stabilizer by CA and epoxy.

3mm

Securely glue together. If coming off during flights, you 'll

lose control of your airplane which leads to accidents!

Glue the elevator to the stabilizer by CA and epoxy.

Blind Nut (4mm)

Engine mount (68x105mm)

Linkage Stopper

Washer(4x8mm)

Screw (4x35mm)

Spring Washer (4mm)

Nut (4mm)

Screw (4x25mm)

Plastic tube (2x400mm)

Fuel tank (550cc) 1

In case of 2-cycle & 4-cycle engine.

The front view of the engine installation finished.

158 mm

The side sketch map of the engine installation finished.

Washer (4x8mm)

Screw (4x35mm)

Screw (4x25mm)

Nut (4mm)

Spring Washer (4mm)

4mm

Install the engine carefully.

Drill 4 holes and set blind nut in appropriate position

in the firewall before install the engine.

5.2mm

Blind Nut

Blind Nut (4mm) 4

Accessory list for the coming installation steps.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Troy Built Models Spielzeug Handbücher

Troy Built Models

Troy Built Models PA-25 Bedienungsanleitung

Troy Built Models

Troy Built Models Hawker hurricane MK.IIa Bedienungsanleitung

Troy Built Models

Troy Built Models Electric Beaver Bedienungsanleitung

Troy Built Models

Troy Built Models F-4u Corsair Bedienungsanleitung

Troy Built Models

Troy Built Models T-28 Trojah Bedienungsanleitung

Troy Built Models

Troy Built Models Ki84 Hayate Bedienungsanleitung

Troy Built Models

Troy Built Models BF-110C ZERSTORER Bedienungsanleitung

Troy Built Models

Troy Built Models Hawker Typhoon Bedienungsanleitung

Troy Built Models

Troy Built Models Stinson 108 Bedienungsanleitung

Troy Built Models

Troy Built Models Fw-190 D9 Bedienungsanleitung

Troy Built Models

Troy Built Models P-51B Mustang Bedienungsanleitung

Troy Built Models

Troy Built Models SHOCKJET MF 6 Bedienungsanleitung

Troy Built Models

Troy Built Models 105” Curtiss JN-4 Bedienungsanleitung

Troy Built Models

Troy Built Models P-40 warhawk Bedienungsanleitung

Troy Built Models

Troy Built Models P-39 Airacobra Bedienungsanleitung

Troy Built Models

Troy Built Models B-25 Mitchell Bedienungsanleitung

Troy Built Models

Troy Built Models Memphis Belle B-17 Bedienungsanleitung

Troy Built Models

Troy Built Models DC-3 Bedienungsanleitung

Troy Built Models

Troy Built Models F86D DOG SABRE Bedienungsanleitung

Troy Built Models

Troy Built Models FAIREY SWORDFLSH Bedienungsanleitung

Troy Built Models

Troy Built Models ROBIN DR400 Bedienungsanleitung

Troy Built Models

Troy Built Models Aichi D3A1 Bedienungsanleitung

Troy Built Models

Troy Built Models Bonanza V-35 Bedienungsanleitung

Troy Built Models

Troy Built Models ME - 109 Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Handbuch

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

Meccano

Meccano 15103 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung