Trumpf TruTool TKF 1500 Bedienungsanleitung

Operator's manual

TruTool TKF 1500 (1A1), (1B1)

Table of contents

1 Safety 4

1.1 General safety information 4

1.2 Specific safety information for beveler 4

2 Description 6

2.1 Intended use 6

2.2 Technical data 7

2.3 Symbols 9

2.4 Noise and vibration information 9

3 Setting work 11

3.1 Adjusting the ram length 11

3.2 Adjusting the angle of bevel 13

3.3 Setting material thickness 14

3.4 Selecting cutting tool 14

3.5 Adjusting height of the cutting tool 15

3.6 Select gear 16

3.7 Accessories included 17

Securing the chip box 17

Handle base 18

Tube-shaped handle 18

Roller holder 19

3.8 Options 20

Roller holder for pipe and tube processing 20

Special tool for pipe and tube processing 21

Conversion kits for large material thick-

nesses

Suspension bracket 25

Workstation 26

4 Operation 28

4.1 Working with TruTool TKF 1500 (1A1), (1B1) 28

5 Maintenance 30

5.1 Regrinding cutting tool 30

5.2 Changing the cutting tool 31

5.3 Change the sliding sleeve 32

2Table of contents E681en_02

6 Accessories and consumables 34

6.1 Ordering consumables 35

7 Appendix: Declaration of conformity, guar-

antee, replacement parts lists

E681en_02 Table of contents 3

1. Safety

1.1 General safety information

■Read all the safety information and instructions including

those in the brochure also supplied.

■Failure to comply with the safety information and instructions

can cause electric shock, burns and/or serious injury.

■Retain all the safety information and instructions for future

use.

Electrical voltage! Risk of fatal injury due to electric shock!

ØRemove the plug from the plug socket before undertaking

any maintenance work on the machine.

ØCheck the plug, cable and machine for damage each time

before using the machine.

ØKeep the machine dry and do not operate it in damp rooms.

ØConnect the fault current (FI) circuit breaker with a maxi-

mum breaking current of 30 mA when using the electric tool

outside.

ØProtect the machine cable in areas where there are sparks.

ØOnly use original TRUMPF accessories.

Damage to the machine due to improper handling.

ØWear safety glasses, hearing protection, protective gloves

and working shoes when working.

ØConnect the plug only when the machine is switched off.

Pull the power plug after use.

ØDo not carry the machine by the cable.

ØHave maintenance carried out by specialists.

1.2 Specific safety information for

beveler

Electrical voltage! Risk of fatal injury due to electric shock!

ØAlways lay the power cable away from the back of the

device and do not pull it over sharp edges.

ØDo not perform any work that may cause the machine to

come into contact with hidden power lines or its own cable.

Contact with a live conductor can cause metallic machine

parts to become live and can lead to an electric shock.

4Safety E681en_02

DANGER

WARNING

DANGER

Risk of injury to hands.

ØDo not reach into the processing line with your hands.

ØUse both hands to hold the machine.

Risk of injury from hot and sharp chips!

Chips exit the chip ejector at high speed.

ØUse the chip box.

Risk of injury from falling machinery

The entire weight of the machine must be taken up after

machining the workpiece.

ØUse the suspension bracket with balancer.

ØUse the suspension cable.

Damage to property due to improper handling.

Collisions could result from setting the machine incorrectly.

ØRotate the eccentric shaft one full turn in a clockwise direc-

tion using the Allen key provided. If no more collisions

occur, remove the Allen key and put the machine into oper-

ation in accordance with regulations.

E681en_02 Specific safety information for beveler 5

WARNING

CAUTION

2. Description

1 Cutting tool

7 Clamping screw (fixing screw

for the supporting body)

15 Eccentric shaft

20 Supporting body

24 Stripper

25 Supporting roller

37 Spindle (for setting material

thickness)

43 Rest plate

49 Cap screw

56 Side plate, right

59 Side plate, left

65 Crank sliding block

226 On/Off switch

TruTool TKF 1500 beveler (1A1), (1B1) Fig. 13201

2.1 Intended use

The TRUMPF TruTool TKF 1500 beveler (1A1), (1B1) is an elec-

trical powered hand-held device designed for the following appli-

cations:

■Preparation of all K-, V-, X-and Y-shaped welding grooves

usual for gas and electrical fusion welding with various con-

tinuously adjustable angles of bevel and continuously adjust-

able lengths of bevels.

■Forming of uniform, oxide-free, bright metallic welding bevel

edges in steel and aluminum.

■Machining of chromium steel and similar high-tensile materi-

als (recommendation: machine in 2-gear version).

6Description E681en_02

■Bevelling of straight and curved edges, provided the mini-

mum radius of the inner curve is 55 mm.

■Bevelling of edges on level and crooked workpieces, in par-

ticular tubes with an inside diameter of at least 100 mm.

■Bevelling of edges in both directions, with the bevelling proc-

ess being able to be started and finished at any point of the

sheet edge.

■Bevelling of edges on large, bulky workpieces, for which the

bevelling machine is guided as a hand-held device.

■Bevelling of edges in normal position (carrier below the

machine) and in "upside-down position" (carrier above the

machine), which is of advantage in particular when bevelling

X and K welding joints.

The TRUMPF TruTool TKF 1500 beveler (1B1) also offers 2-

gear changing for modifying the working speed when machining

high-tensile materials.

2.2 Technical data

Other countries USA

Values

Voltage 230 V 120 V 110 V 120 V

Frequency 50/60 Hz 50/60 Hz

Max. length of bevel "ls" continuously adjustable:

Mild steel

with 400 N/mm²

15 mm 0.59 in

Mild steel

with 600 N/mm²

9 mm 0.354 in

Mild steel

with 800 N/mm²

6 mm 0.236 in

Working speed 2 m/min 6.55 ft/min

Nominal power con-

sumption

2000 W -

Nominal current - 15 A

Stroke rate with nominal

load

370/min 340/min 340/min 340/min

Weight 16.5 kg 36.7 lbs

Material thicknesses:

Min. 6 mm 0.236 in

Max. 40 mm 1.57 in

Special 40-80 mm

80-120 mm

120-160 mm

1.57-3.14 in

3.14-4.71 in

4.71-6.28 in

Angle of bevel "ß" con-

tinuously adjustable

20°-45° 20°-45°

With special stripper 20°-55° 20°-55°

Smallest radius with

inner cutouts

55 mm 2.17 in

E681en_02 Technical data 7

TruTool TKF 1500 (1A1)

Other countries USA

Values

Safety classSafety class

II / II /

Tab. 1

Other countries USA

Values

Voltage 230 V 120 V 110 V 120 V

Frequency 50/60 Hz 50/60 Hz

Max. length of bevel "ls" continuously adjustable:

Mild steel

with 400 N/mm²

15 mm (1st + 2nd gear) 0.59 in

Mild steel

with 600 N/mm²

11 mm (1st gear)

9 mm (2nd gear)

0.433 in

0.354 in

Mild steel

with 800 N/mm²

9 mm (1st gear)

6 mm (2nd gear)

0.354 in

0.236 in

Working speed 1.25 m/min

(1st gear)

2 m/min

(2nd gear)

4.1 ft/min

(1st gear)

6.55 ft/min

(2nd gear)

Nominal power con-

sumption

2000 W -

Nominal current - 15 A

Stroke rate with nominal

load

230/min

(1st

gear)

370/min

(2nd

gear)

170/min

(1st gear)

340/min

(2nd gear)

170/min

(1st gear)

340/min

(2nd gear)

Weight with guide han-

dle

19.5 kg 43.3 lbs

Material thicknesses:

Min. 6 mm 0.236 in

Max. 40 mm 1.57 in

Special 40-80 mm

80-120 mm

120-160 mm

1.57-3.14 in

3.14-4.71 in

4.71-6.28 in

Angle of bevel "ß" con-

tinuously adjustable

20°-45° 20°-45°

With special stripper 20°-55° 20°-55°

Smallest radius with

inner cutouts

55 mm 2.17 in

Safety class

II / II /

Tab. 2

8Technical data E681en_02

TruTool TKF 1500 (1A1)

TruTool TKF 1500 (1B1)

2.3 Symbols

Note

The following symbols are important for reading and understand-

ing the instruction manual. The correct interpretation of the sym-

bols will help you operate the machine better and safer.

Symbol Name Meaning

Read operating manual Read the operator's manual and safety information in

their entirety before starting up the machine. Closely

follow the instructions given.

Safety class II Indicates a doubly insulated tool.

Alternating current Type or property of current

V Volt Voltage

A Ampere Current, current input

Hz Hertz Frequency (oscillations per second)

W Watt Power, power input

mm Millimeters Dimensions e.g.: material thickness, chamfer length

in Inch Dimensions e.g.: material thickness, chamfer length

noIdle speed Revolution speed without load

.../min Revolutions/strokes per minute Revolution speed, stroke rate per minute

Tab. 3

2.4 Noise and vibration information

Noise emission value may be exceeded.

ØWear hearing protection.

Vibration emission value may be exceeded.

ØSelect tools correctly and replace them promptly when they

show wear.

ØMaintenance may be carried out by trained specialist techni-

cians only.

ØEstablish additional safety precautions for the protection of

the operator against the effects of vibrations (e.g. keeping

hands warm, organizing the work sequences, machining with

normal feed power).

Notes

■The specified vibration emission value was measured in

accordance with a standardized testing procedure and can

be used to compare one electric tool with another.

E681en_02 Symbols 9

WARNING

■The specified vibration emission value can also be applied

for a provisional estimate of the vibration load.

■Times during which either the machine is switched off or run-

ning but not actually in use can considerably reduce the

vibration load during the entire working period.

Designation of measured value Unit Value according to

EN 60745

Vibration emission value ah (vector

sum of three directions)

m/s212.1

Uncertainty K for vibration emission

value

m/s22.5

A-class acoustic pressure level LPA

typically

dB (A) 87

A-class acoustic power level LWA

typically

dB (A) 98

Uncertainty K for noise emission

value

dB 1.5

Tab. 4

10 Noise and vibration information E681en_02

Andere Handbücher für TruTool TKF 1500

Inhaltsverzeichnis

Andere Trumpf Elektrowerkzeuge Handbücher

Trumpf

Trumpf TruTool F 300 (3B1) Bedienungsanleitung

Trumpf

Trumpf TruTool S 160 Bedienungsanleitung

Trumpf

Trumpf TruTool N 200 Bedienungsanleitung

Trumpf

Trumpf TruTool C 250 (1B1) Bedienungsanleitung

Trumpf

Trumpf TruTool TF 350 Bedienungsanleitung

Trumpf

Trumpf TruTool TKF 700 Bedienungsanleitung

Trumpf

Trumpf TruTool N 350 Bedienungsanleitung

Trumpf

Trumpf TruTool N 160 E Bedienungsanleitung

Trumpf

Trumpf TruTool TKF 1100 Bedienungsanleitung

Trumpf

Trumpf S 160 E Bedienungsanleitung

Trumpf

Trumpf TruTool C 160 1A1 Bedienungsanleitung

Trumpf

Trumpf TruTool N 1000 Bedienungsanleitung

Trumpf

Trumpf TKA 500-0 Bedienungsanleitung

Trumpf

Trumpf N 700-2 Bedienungsanleitung

Trumpf

Trumpf TruTool S 450 Bedienungsanleitung

Trumpf

Trumpf TruTool TKF 1500 3A1 Bedienungsanleitung

Trumpf

Trumpf TruTool TKF 1500 Bedienungsanleitung

Trumpf

Trumpf TruTool C 160 Bedienungsanleitung

Trumpf

Trumpf TruTool N 160 2A5 Bedienungsanleitung

Trumpf

Trumpf TKA 300-0 Bedienungsanleitung

Trumpf

Trumpf N700-1 Bedienungsanleitung

Trumpf

Trumpf TruTool N 350 Bedienungsanleitung

Trumpf

Trumpf N 200-5 Bedienungsanleitung

Trumpf

Trumpf TruTool F 125 (2A1) Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch