TSC TTP-2410M Bedienungsanleitung

TTP-2410M/346M/644M

TTP-246M Plus/344M Plus

Bar Code Printer Service Manual

4.2 Mechanism Fine Adjustment to Avoid Ribbon Wrinkles

This printer has been fully tested before delivery. There should be no ribbon wrinkle

presented on the media for general-purpose printing application. Ribbon wrinkle is related to

the media thickness, print head pressure balance, ribbon film characteristics, print darkness

setting…etc. In case the ribbon wrinkle happens, please follow the instructions below to

adjust the printer parts.

Adjustable

Printer

Parts

Symptom 1. Wrinkle happens from label lower left to

upper right direction ("Ԩ")

2. Wrinkle happens from label lower right

to upper left direction ("Ԫ")

Wrinkle

Example

Feed direction

Ribbon guide plate

Print head pressure

adjustment knob Z-axis mechanism

adjustment knob

TTP-2410M/346M/644M

TTP-246M Plus/344M Plus

Bar Code Printer Service Manual

Adjust the print head pressure adjustment knob

The print head pressure adjustment knob has 5

levels of settings. Clockwise direction adjustment

is to increase the print head pressure. Counter

Clockwise adjustment can decrease the print

head pressure.

If the wrinkle on the label starts from the lower left

side to upper right side, please do following

adjustment.

1. Decrease the right side print head pressure

adjustment knob setting 1 level per each

adjustment then print the label again to check if

wrinkle is gone.

2. If the right side print head adjustment knob

setting has been set to index 1 (the lowest

pressure index), please increase the left side

print head pressure.

3. If the left side print head adjustment knob

setting has been set to 5 (the highest pressure

index) the wrinkle can’t be avoid, please rotate

the both knobs back to setting 1 then rotate the

Z-axis mechanism adjustment knob clockwise

for a few degrees and print again for fine tune

the print head pressure distribution.

Note for step 3:

*Factory default setting, the Z-axis knob is rotated

counter clockwise to the end of thread.

*Turn the Z-axis mechanism adjustment knob

clockwise until you feel the knob touch the

mechanism for the first adjustment.

* If the wrinkle is still there, please turn the Z-axis

mechanism adjustment knob clockwise about

1/4 circle each time for adjustment

* If the winkled direction is change from "Ԩ" to "

Ԫ" by adjusting the Z-axis mechanism

adjustment knob, please turn the Z axis

mechanism adjustment knob counter clockwise

to avoid the wrinkle.

Adjust the print head pressure adjustment knob

The print head pressure adjustment knob has 5

levels of settings. Clockwise direction adjustment

is to increase the print head pressure. Counter

Clockwise adjustment can decrease the print

head pressure.

If the wrinkle on the label starts from the lower

right side to upper left side, please do following

adjustment.

1. Decrease the left side print head pressure

adjustment knob setting 1 level per each

adjustment then print the label again to check if

wrinkle is gone.

2. If the left side print head adjustment knob level

has been set to index 1 (the lowest index),

please increase the right side print head

pressure.

Right knob

Left knob Right knob

Left knob

Z axis mechanism

adjustment knob

Andere Handbücher für TTP-2410M

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere TSC Barcode-Lesegerät Handbücher

TSC

TSC TTP-245 Plus Bedienungsanleitung

TSC

TSC TTP-245 Plus Bedienungsanleitung

TSC

TSC TTP-245C series Bedienungsanleitung

TSC

TSC 4T520 Series Bedienungsanleitung

TSC

TSC TTP-268M Bedienungsanleitung

TSC

TSC Alpha-40L RFID Bedienungsanleitung

TSC

TSC PRINTRONIX TX210 Series Bedienungsanleitung

TSC

TSC XP-DT425B Series Bedienungsanleitung

TSC

TSC TDP-245 Series Bedienungsanleitung

TSC

TSC TDP-643R Plus series Bedienungsanleitung

TSC

TSC TE200 series Bedienungsanleitung

TSC

TSC TDP-225W Bedienungsanleitung

TSC

TSC TDP-245 Series Bedienungsanleitung

TSC

TSC TTP-2610MT Series Bedienungsanleitung

TSC

TSC TE200 series Bedienungsanleitung

TSC

TSC ME240 series Bedienungsanleitung

TSC

TSC TC200 Series Bedienungsanleitung

TSC

TSC TTP-243 Series Bedienungsanleitung

TSC

TSC TTP-244ME Pro Bedienungsanleitung

TSC

TSC TTP 244M Pro Series Bedienungsanleitung

TSC

TSC TDM-20 Bedienungsanleitung

TSC

TSC TTP-245C series Bedienungsanleitung

TSC

TSC TTP-243 Pro Series Bedienungsanleitung

TSC

TSC 4D200 Series Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung