TSI Instruments 3783 Gebrauchs- und Pflegehandbuch

TSI and TSI logo are registered trademarks of TSI Incorporated.

Microsoft, and Windows are registered trademarks of Microsoft Corporation.

CONDENSATION

PARTICLE COUNTERS

MODELS: 3783, 3787 AND 3788

FIRMWARE UPDATE INSTRUCTIONS

The Condensation Particle Counter (CPC)Firmware Update application loads firmware onto a TSI®CPC

instrument through a USB connection. The CPCFirmware Update runs on a computer with Microsoft

Windows®XP (32-bit only), Windows®7 (32-bit or 64-bit) or Windows®8 (32-bit or 64-bit) operating

system. This application is to be used with TSI CPCinstruments only.

Obtaining the Latest CPCFirmware Update Program from the

TSI Website

1. From your computer, access the TSI web site http://www.tsi.com/SoftwareDownloads and follow the

instructions on the web page to locate firmware for your CPC.

2. Click on the resulting Firmware Update link to download the file to your computer.

Updating your CPC to the Latest Firmware

1. Once the firmware update application is on your computer (see above), the firmware can be

transferred to your CPC.

C a u t i o n

Before updating the firmware on your CPC you must first disconnect any RS-232

connection to the CPC. Failure to do this can result in an inoperable instrument. If you

have trouble upgrading the firmware in the unit, TSI recommends that you contact

customer service at www.tsi.com, 1-800-874-2811 or email pa[email protected] to

resolve the issue before you send the unit back to TSI.

2. Before connecting your CPC to the computer for the first time, make sure you are connected to the

internet as the system may need to download software from Windows Update.

3. Using a USB cable, connect to the Series B receptacle (square shape) on your CPCand a USB

receptacle on your computer.

4. Turn on the CPC and allow it to complete its initialization sequence. If the New Hardware Wizard

appears on your computer, simply follow the prompts to connect your instrument to your computer.

Continue past any warnings and press Finish. If needed, the Using the New Hardware Wizard

section provides additional information.

5. Run the firmware update application you downloaded to begin the CPC firmware update.

Firmware Update Instructions —page 2 of 7

6. Your CPC will be automatically detected by the application.

i. If your instrument cannot be found, the following message appears (Figure 1):

Figure 1

ii. If your instrument is found, a message similar to the following appears (Figure 2). Click Yes to

begin the firmware update or Cancel to cancel it.

Figure 2

7. Once started, the firmware update process should take approximately 2 minutes. During this time,

observe the progress shown by the firmware update application (Figure 3).

Figure 3

8. After the update is completed successfully, the CPC will reset itself and the firmware update

application will display a “Done” button (Figure 4). Click the Done button to close the application.

Figure 4

9. Verify that the Firmware Version reported by the CPC corresponds with the version you just uploaded

to the instrument.

Firmware Update Instructions —page 3 of 7

Using the New Hardware Wizard to connect to your CPC

1. The New Hardware Wizard screens may appear when your CPC is connected to your computer.

Typically this will only happen the first time the CPC is connected to a Windows XP system.

2. Select Yes, this time only to search for software on the Windows®Update website. Then select the

Next > button (Figure 5).

Figure 5

3. Select the Install the software automatically action. Then select the Next > button (Figure 6).

Figure 6

Firmware Update Instructions —page 4 of 7

4. The wizard will now search for and install required software (Figure 7 and Figure 8).

This may take several minutes.

Figure 7

Figure 8

Firmware Update Instructions —page 5 of 7

5. Make sure that the device installed without any errors. Select the Finish button to complete the

device installation and exit the dialog (Figure 9).

Figure 9

6. The installation will continue with another New Hardware Wizard.

7. Again, select Yes, this time only to search for software on the Windows®Update website. Then

select the Next > button (Figure 10).

Figure 10

Firmware Update Instructions —page 6 of 7

8. Select the Install the software automatically action. Then select the Next > button

(Figure 11).

Figure 11

9. The wizard will now search for and install required software (Figure 12 and Figure 13).

Figure 12

TSI Incorporated –Visit our website www.tsi.com for more information.

USA Tel: +1 800 874 2811

UK Tel: +44 149 4 459200

France Tel: +33 4 91 11 87 64

Germany Tel: +49 241 523030

India Tel: +91 80 67877200

China Tel: +86 10 8219 7688

Singapore Tel: +65 6595 6388

Figure 13

10. Make sure that the device installed without any errors. Select the Finish button to complete the

device installation and exit the dialog (Figure 14).

Figure 14

11. The CPCinstrument is installed on the system and is ready to have new firmware uploaded.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere TSI Instruments Laborausrüstung Handbücher

TSI Instruments

TSI Instruments AeroTrak+ Bedienungsanleitung

TSI Instruments

TSI Instruments 3772 Bedienungsanleitung

TSI Instruments

TSI Instruments 3760 Bedienungsanleitung

TSI Instruments

TSI Instruments 3082 Bedienungsanleitung

TSI Instruments

TSI Instruments 3775 Bedienungsanleitung

TSI Instruments

TSI Instruments AeroTrak 9110 Series Bedienungsanleitung

TSI Instruments

TSI Instruments BIOTRAK 9510-BD-P Bedienungsanleitung

TSI Instruments

TSI Instruments SIZER EEPS 3090 Bedienungsanleitung

TSI Instruments

TSI Instruments AEROTRAK 9310 Installationshandbuch

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung