TSI Instruments Cheetah CH-5 Bedienungsanleitung

buyTSI.com - 800.223.4540

800.223.4540

Read this manual before operating

Tire Service International, LLC

3451 S. 40TH ST.

Phoenix, AZ 85040

Ofce: 602.437.5020

Email: [email protected]

Fax: 602.437.5025

Made in Taiwan

Cheetah® Bead Seater

CH-5 & FCH-5 & CH-10

Includes AL & CRN models

Revised: April 2022

buyTSI.com - 800.223.4540

Overview

• WARNING: CHEETAH® TANKS BLAST AIR AT A HIGH RATE.

• Personal Protective Equipment (Safety goggles, gloves, non-skid shoes and hearing

protection are suggested).

• NEVER TRANSPORT OR STORE A CHARGED TANK - Accidental discharge could cause

serious injury or damage

• Use proper body positioning.

• Always keep work clean, uncluttered, and well lit. Do Not work on a slippery oor surface.

• Keep bystanders out of the work area while operating.

• Never point an air tool at people or animals.

• Detach from air supply and release all air pressure before installing, removing or adjusting

any accessory on this tool or performing maintenance. Failure to do so could result in injury.

• Do not open the Cheetah® Bead Seater air release valve when connecting the air supply

hose. When the Cheetah® Bead Seater is not in use, discharge air from tank. Store with valve

open in a clean, dry location.

• If the unit appears damaged in any way, is missing parts, or operates abnormally, it shall be

removed from service immediately. All units that have been dropped, impacted suddenly,

or dented should be removed from service

The CH-5 Cheetah® Bead Seater accommodates wheels from 4” to 24.5”. This includes

passenger and light truck tires and most commercial truck tires.

The CH-10 Cheetah® Bead Seater accommodates passenger and light truck tires, commercial

truck and some implement tires.

Safety Instructions

Fig. 1

Handle

Fill Valve

Pressure Gauge

Threaded Barrel

and Lock Nut

Pipe Nipple and

Discharge Valve

Safety Release

Valve

buyTSI.com - 800.223.4540

Verify receiving all the parts described in this instruction. Assemble as shown in Fig. 2 thru Fig 8.

Setup Instructions

Fig. 2 Fig. 3

Fig. 4 Fig. 5

To install the discharge valve and threaded barrel use a large pipe wrench or a large

socket wrench. Tighten so air doesn’t leak out of the tting. Use Teon tape where

applicable. Put some air in the tank and use soapy water to check tting connections for

air leaks. Tighten them as necessary.

In Fig. 6, tighten the lock nut ensuring the channel side of the threaded barrel is facing

up as shown in Fig. 5. If the safety release valve in Fig 7. comes loose tighten it as shown.

WARNING: DO NOT REMOVE SAFETY RELEASE. Excessive pressure could cause tank

to rupture causing serious injury or death.

Note position

of discharge

valve handle.

Fig. 6 Fig. 7

Note: This

end up

buyTSI.com - 800.223.4540

Operational Instructions

If the pressure gauge becomes loose, tighten it

with a wrench as shown in Fig. 8 and test for air

leaks with soapy water.

Fig. 8

TSI suggests using a quick-disconnect tting (not included) on the air line to attach the air line

to the valve stem. Remove valve stem core from wheel. Set aside to replace later after bead is

seated.

Lubricate tire beads and rim anges with approved tire lubricant.

As shown in Fig. 9 positioning a wheel on the tire stand to elevate both the tire and rim.

Connect the air hose to valve stem in Fig. 10. You may have to thread the air line through the rim

center if the valve stem is facing the ground. In most cases, the wide ange of the wheel should

be facing up.

The lower tire bead must be resting on the wheel bead-seat area. This alignment is very

important to ensure the tire will capture the air blast within the tire cavity.

Now you are ready to seat the tire bead onto the rim.

Fig. 9 Fig. 10

IMPORTANT: Prepare each wheel by cleaning

the rim. Dirt on the rim can create ying debris

from the rush of air going into the tire.

buyTSI.com - 800.223.4540

Firmly hold Cheetah® tank as shown in Fig. 12. Lean forward slightly to hold it in position. Point

the threaded barrel down into the tire as shown in Fig. 13. Usually this is a 45 degree angle, but

will vary from one tire to another. Open valve on air hose.

Gather your footing, hold one hand onto the Cheetah® handle and the other on the discharge

valve lever. Fully open the discharge valve lever quickly releasing all the air into the tire, lifting

the bead. See Fig 11-A.

Once the bead fully moves into position close the air supply valve. Remove the hose locking

chuck from the valve stem and replace valve stem core. With experience you will recognize lling

the tank to capacity isn’t necessary. The amount of air to seat the bead depends on the tire. Most

tires can be seated between 40 PSI- 100 PSI. Several attempts to seat the bead may be necessary.

Make sure the valve stem core is rmly tightened in place. You are now ready to place the tire

into a tire cage and proceed to inate the tire to manufacturer’s tire pressure requirements.

Check for leaks and if necessary repeat process. If none are present, place valve cap on valve stem

and wipe off excess lubricant.

Operational Instructions

NOTE: It is not always necessary to ll the tank to maximum pressure. The required pressure

will vary depending on the size and type of tire. It is best to begin with lower pressure and work

up to optimum pressure for your specic tire.

Never exceed 120 PSI (Safety release valve is set to 120 PSI).

Fig. 11-A

OPEN

CLOSED

Fig. 12 Fig. 13

Fig. 11-B

buyTSI.com - 800.223.4540

Dimensions

Maintenance

To ensure the highest level of performance and operator safety, each Cheetah® tank should

be inspected regularly for signs of damage due to wear, accidental impact from drops or other

shop wear and tear or storage conditions. Inspection of the tank both external/internal and

replacement is the ideal approach to insure optimum user safety. Safety related input from our

tank manufacturers suggest replacement after 5 years in service.

• Daily: Inspect the pressure gauge (Part# 01.106) and Safety Release Valve (Part #05.102).

Visually inspect the exterior of the tank for rust or deterioration.

• Monthly: Pull the ring of the safety release valve to ensure the valve moves freely and isn't

restricted.

• Every six (6) months: Visually inspect the interior of the tank for rust or deterioration by

removing the discharge valve and threaded barrel. Shine a light into the tank to improve

visability.

• Storage and Drain: The Cheetah® should be stored by hanging from the handle with the

valve open. This allows any moisture to drain from the tank when the Cheetah® is not in use.

It also protects the barrel and other attachments on the Cheetah® from damage.

• Discontinue use of tanks should any of the maintenance items need service. Contact your

Distributor or TSI at 800-223-4540 or 602-437-5020 for replacement parts or units.

The (5) year service is based upon safety related input from our tank manufacturer. Following

the maintenance inspection protocol and good judgment of the user, should be the nal

determination of the unit’s safety and need for replacement. Under NO circumstances should

you use a tank with signs of deterioration, damage or malfunction safety valves or gauges.

Use genuine Cheetah® TSI replacement parts. Use of non-cheetah parts will void the warranty.

Under no circumstances should items be welded or attached to the tank.

TSI Cheetah® warranty does not cover a dropped tank or damage resulting from dropping the

unit. Any tank that has been dropped or shows sign of damage should be immediately removed

from service.

Model Length Width Height Shipping Wt.

CH-5 18” 14” 14” 30 lbs

CH-5 AL 18” 14” 14” 18 lbs

CH-10 24” 16” 15” 46 lbs

CH-10 AL 24” 16” 15” 29 lbs

buyTSI.com - 800.223.4540

Notes

buyTSI.com - 800.223.4540

Notes

buyTSI.com - 800.223.4540

Notes

ID Item # Description

2 01.104 Nipple 1.5”

3 02.102 Discharge Valve, CH-5

4 02.107 Lock Nut for CH-5 Barrel

5 02.103 Threaded Barrel, CH-5

6 01.106-200 Air Pressure Gauge 1/4 NPT 200 PSI

7 01.107 Reducer, Bushing 3/4 x 1/4

8 03.104 Elbow 1/4 NPT M x 1/4 NPT F x 90 Street Brass

9 05.102 Valve, Safety Release 120psi

10 01.230 Handle & Nut Only For Cheetah Discharge Valves

11 04.103 Valve, Ball Silver/Black

12 12607 Rubber Feet For Bead Seater

12 12608 Screw for Rubber Feet

ID Item # Description

2 02.104 Nipple 2”

3 03.102 Discharge Valve, CH-10

4 03.107 Lock Nut for CH-10 Barrel

5 03.103 Threaded Barrel, CH-10

6 01.106-200 Air Pressure Gauge 1/4 NPT 200 PSI

7 01.107 Reducer, Bushing 3/4 x 1/4

8 03.104 Elbow 1/4 NPT M x 1/4 NPT F x 90 Street Brass

9 05.102 Valve, Safety Release 120psi

10 01.230 Handle & Nut Only For Cheetah Discharge Valves

11 04.103 Valve, Ball Silver/Black

12 12607 Rubber Feet For Bead Seater

12 12608 Screw for Rubber Feet

CH-5 Replacement Parts

CH-10 Replacement Parts

buyTSI.com - 800.223.4540

Optional Items

The magnum barrels provide optimum air dispersion for larger diameter wheels. The curved tube

has holes in it for direct air ow into the tire

Magnum I (CH-5) Item #02.106 Magnum II (CH-10) Item #03.106

Shelf Item #TI-87

Tire Stand Item #01.111

Tire Wedge Item #01.110

Difficult Wheels?

CH-ACC Kit

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere TSI Instruments Messgerät Handbücher

TSI Instruments

TSI Instruments ALNOR MicroManometer AXD 550 Bedienungsanleitung

TSI Instruments

TSI Instruments Q-Trak XP Bedienungsanleitung

TSI Instruments

TSI Instruments AVM430 Bedienungsanleitung

TSI Instruments

TSI Instruments P-TRAK Ultrafine Bedienungsanleitung

TSI Instruments

TSI Instruments 3082 Bedienungsanleitung

TSI Instruments

TSI Instruments ALNOR AVM410 Bedienungsanleitung

TSI Instruments

TSI Instruments 8525 Bedienungsanleitung

TSI Instruments

TSI Instruments Aerotrak 9303 Bedienungsanleitung

TSI Instruments

TSI Instruments DustTrak 8540 Bedienungsanleitung

TSI Instruments

TSI Instruments ALNOR MicroManometer AXD 550 Bedienungsanleitung

TSI Instruments

TSI Instruments Quest The Edge Bedienungsanleitung

TSI Instruments

TSI Instruments DUSTTRAK 8533 Montageanleitung

TSI Instruments

TSI Instruments Alnor Velometer 6000 Series Bedienungsanleitung

TSI Instruments

TSI Instruments HM685 Bedienungsanleitung

TSI Instruments

TSI Instruments ALNOR HM670 Bedienungsanleitung

TSI Instruments

TSI Instruments 3936 Bedienungsanleitung

TSI Instruments

TSI Instruments QUESTemp 32 Bedienungsanleitung

TSI Instruments

TSI Instruments Quest Edge 7 Bedienungsanleitung

TSI Instruments

TSI Instruments IAQ50 Bedienungsanleitung

TSI Instruments

TSI Instruments 8495 Bedienungsanleitung

TSI Instruments

TSI Instruments HM685 Bedienungsanleitung

TSI Instruments

TSI Instruments VELOCICALC 9515 Bedienungsanleitung

TSI Instruments

TSI Instruments DP-CALC 5815 Bedienungsanleitung

TSI Instruments

TSI Instruments Q-TRAK XP 7585 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung