Tyco Electronics 58591-1 Bedienungsanleitung

Instruction Sheet

PRO-CRIMPER* III Hand

Crimping Tool Assembly 58591-1 408-4354

L C B

of 5

2009 Tyco Electronics Corporation, Harrisburg, PA

All International Rights Reserved

TE logo and Tyco Electronics are trademarks.

*Trademark. ther products, logos, and company names used are the property of their respective owners.

T LING ASSISTANCE CENTER 1-800-722-1111

PR DUCT INF RMATI N1-800-522-6752 This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at

www.tycoelectronics.com

11 JUN 09 Rev A

with Die Assembly 58591-2

PROPER USE GUIDELINES

CumulativeTraumaDisorderscanresultfromtheprolongeduseof manuallypoweredhandtools.Handtoolsareintendedforoccasionaluseandlowvolume

applications. A wide selection of powered application equipment for extended-use, production operations is available.

Stationary Jaw

Back of Tool

(Wire Side)

Pivot Pin

PR -CRIMPER III Hand

Crimping Tool Frame

354940-1 (408-9930)

Stationary Handle

Moving Handle

Ratchet Adjustment Wheel

Moving Jaw

Die Assembly

Front of Tool

(Locator Side)

Locator Assembly

(Supplied with

Die Assembly)

The PR -CRIMPER III Hand Crimping Tool Assembly is a Commercial"

grade tool and is designed primarily for field installation, repair, maintenance

work, or prototyping in industrial, commercial, or institutional applications.

Product crimped with this tool will meet the crimp height requirement for hand

tools in the appropriate 114 series specification, but may not comply with other

feature parameters of the specification. Tyco Electronics offers a variety of

tools to satisfy your performance requirements. For additional information,

contact the Tooling Assistance Center at 1-800-722-1111.

TE Die

TE Locator

Contact

ire

TE Di

Assembly

TE L

oca

Assembly

{

Family

}

Size

(mm2)Insul Dia

(mm [in.]) Strip Length

(mm [in.])

Micro 0.75

58591-2 58515-3 Power

Quadlok

1.0 3.40

[.134]

3.81 - 4.60

[.150

.181]

Quadlok

Seal 0.5

[

134]

[

150

181]

{

Supplied with die assembly, also available separately.

}

Contact the Tooling Assistance Center or Product

Information Center (see below) for specific contact part

numbers.

Figure 1

1. INTRODUCTION

PRO–CRIMPER III Hand Crimping Tool Assembly

58591–1 consists of Die Assembly 58591–2 and

PRO–CRIMPER III Hand Crimping Tool Frame

354940–1. The die assembly consists of crimping

dies and a locator assembly.

Read these instructions thoroughly before crimping

any contacts.

Reasons for revision are listed in Section 11,

REVISION SUMMARY.

Dimensions on this sheet are in millimeters [with

inch equivalents provided in brackets]. Figures

and illustrations are for identification only and are

not drawn to scale.

2. DESCRIPTION

(Figures 1 and 2)

The tool features a tool frame with a stationary jaw

and handle, a moving jaw, a moving handle, and an

adjustable ratchet that ensures full contact crimping.

The tool frame holds a die assembly with three

crimping sections.

NOTE

408-4354

PRO-CRIMPER III H nd Crimping Tool Assembly 58591-1

Rev

f5 Tyc Electr nics C rp rati n

Figure 2

Nut L cat r

Assembly T l Frame

Die Retaining Pins

Die Retaining Screws

Chamfer

Insulati n Anvil

Wire Anvil

Offset

Wire Crimper

Chamfer Insulati n

Crimper

The die assembly features a wire anvil, an insulation

anvil, a wire crimper, and an insulation crimper.

Attached to the outside of the frame is a locator

assembly, which contains a locator, a spring retainer,

and a contact support.

Die retaining pins and die retaining screws are used

to position and secure the dies in the tool frame. A

nut is used on the upper die retaining screw to hold

the locator assembly in place.

3. INSTALLATION AND REMOVAL OF DIE SET

AND LOCATOR ASSEMBLY

(Figure 2)

1. Open the tool handles and remove the two die

retaining screws from the tool jaws.

2. Place the wire anvil and insulation anvil so that

their chamfered sides and their marked surfaces

face outward, when mounted in the moving jaw of

the tool frame.

3. Insert the two die retaining pins.

4. Insert the short die retaining screw through the

jaw and through both anvil dies, and tighten the

screw just enough to hold the dies in place. Do

not

tighten the screw completely at this time.

5. Place the wire crimper and insulation crimper so

that their chamfered sides and their marked

surfaces face outward, when mounted in the

stationary jaw of the tool frame.

6. Insert the two die retaining pins.

7. Insert the long die retaining screw through the

jaw and through both crimper dies, and tighten the

screw just enough to hold the dies in place. Do

not

tighten the screw completely at this time.

8. Carefully close the tool handles, making sure

that the anvils and crimpers align properly.

Continue closing the tool handles until the ratchet

in the tool frame has engaged sufficiently to hold

the anvils and crimpers in place, then tighten both

die retaining screws.

9. Place the locator assembly over the end of the

long screw, and position the locator assembly

against the side of the tool jaw.

10. Place the nut onto the end of the long screw

and tighten the nut enough to hold the locator

assembly in place, while still allowing the locator to

slide up and down.

11. To disassemble, close the tool handles until the

ratchet releases, remove the nut, the locator

assembly, the two die retaining screws, and the

four die retaining pins, and slide the anvils and

crimpers out of the tool jaws.

4. CONTACT SUPPORT ADJUSTMENT

(Figure 3)

The contact support is preset prior to shipment,

but minor adjustment may be necessary.

NOTE

408-4354

PRO-CRIMPER III Hand Cri ping Tool Asse bly 58591-1

of 5Rev

Tyco Elec ronics Corpora ion

1. Make a sample crimp and determine if the

contact is straight, bending upward, or bending

downward.

2. If adjustment is required, loosen the screw that

holds the contact support onto the locator

assembly.

The ratchet has detents that create aud ble cl cks

as the tool handles are closed.

3. Place a contact with wire into the proper nest

and close the tool handles until the ratchet reaches

the sixth click, or until the contact support touches

the contact.

4. Slightly loosen the nut that holds the locator

assembly onto the tool frame.

5. Move the contact support as required to

eliminate the bending of the contact.

6. Tighten the nut and close the handles until the

ratchet releases.

7. Remove and inspect the contact.

8. Make another sample crimp. If the contact is

straight, tighten the contact support screw. If the

contact is still being bent during crimping, repeat

the adjustment procedure.

5. CRIMPING PROCEDURE

Th s tool s prov ded w th a cr mp adjustment

feature. Int ally, the cr mp he ght should be

ver f ed as spec f ed n F gure 4. Refer to Sect on

6, CRIMP HEIGHT INSPECTION, and Sect on 7,

RATCHET ADJUSTMENT, to ver fy cr mp he ght

before us ng the tool to cr mp des red contacts

and w re s zes.

Refer to the table in Figure 1 and select wire of the

specified size and insulation diameter. Strip the wire

to the length indicated in Figure 1, taking care not to

nick or cut wire strands. Select an applicable contact

and identify the appropriate crimp section according

to the wire size markings on the tool. Refer to

Figure 3 and proceed as follows:

1. Hold the tool so that the back (wire side) is

facing you. Squeeze tool handles together and

allow them to open fully.

2. Holding the contact by the mating end, insert the

contact — insulation barrel first — through the front

of the tool and into the appropriate crimp section.

3. Position the contact so that the mating end of

the contact is on the locator side of the tool, and so

that the open “U” of the wire and insulation barrels

must face the top of the tool. Place the contact up

into the nest so that the movable locator drops into

the slot in the contact. Refer to Figure 3. Butt the

front end of the wire barrel against the movable

locator.

Make sure that both s des of the nsulat on barrel

are started evenly nto the cr mp ng sect on. Do

NOT attempt to cr mp an mproperly pos t oned

contact.

Figure 3

Adjus men

Screw for

Con ac

Suppor

Con ac

Suppor Loca or

Back of Tool

(Wire Side)

Wire

Con ac

(Typ)

Loca or in

Wire S op Slo Wire

Inser ed

o S op

S rip

Leng h

Wire

Seal

Wire

Seal

NOTE

CAUTION

408-4354

PRO-CRIMPER III Hand Crimping Tool Assembly 58591-1

Rev

of 5 Tyco Electronics Corporation

4. Hold the contact in position and squeeze the

tool handles together until ratchet engages

sufficiently to hold the contact in position. Do NOT

deform insulation barrel or wire barrel.

5. Insert stripped wire, with wire seal, into contact

insulation and wire barrels until it is butted against

the wire stop, as shown in Figure 3.

6. Holding the wire in place, squeeze tool handles

together until ratchet releases. Allow tool handles

to open and remove crimped contact.

The crimped contact may stick in the crimping

area, but the contact can be easily removed by

pushing downward on the top of the locator (see

Figure 3).

7. Check the contact’s crimp height as described in

Section 6, CRIMP HEIGHT INSPECTION. If

necessary, adjust the crimp height as described in

Section 7, CRIMP HEIGHT ADJUSTMENT.

6. CRIMP HEIGHT IN PECTION

Crimp height inspection is performed through the use

of a micrometer with a modified anvil, commonly

referred to as a crimp–height comparator. Tyco

Electronics does not manufacture or market

crimp–height comparators. Detailed information on

obtaining and using crimp–height comparators can be

found in instruction sheet 408–7424.

Proceed as follows:

1. Refer to Figure 4 and select a wire (maximum

size) for each crimp section listed.

2. Refer to Section 5, CRIMPING PROCEDURE,

and crimp the contact(s) accordingly.

3. Using a crimp height comparator, measure the

wire barrel crimp height as shown in Figure 4. If the

crimp height conforms to that shown in the table,

the tool is considered dimensionally correct. If not,

the tool must be adjusted. Refer to Section 7,

RATCHET (Crimp Height) ADJUSTMENT.

7. RATCHET (Crimp Height) ADJU TMENT

(Figure 5)

1. Remove the lockscrew from the ratchet

adjustment wheel.

2. With a screwdriver, adjust the ratchet wheel

from the locator side of the tool.

Position Point

on Center of

Wire Barrel

Opposite

Seam

A"

Mo ifie Anvil

WIRE IZE CRIMP ECTION CRIMP HEIGHT

DIM.

(

)

AND

mm2(MAX) (WIRE IZE MARKING)

()

TOLERANCE

+.05 [+.002]

0.75 0.75 1.27

[.0500]

1.0 1.0 1.36

[.0535]

0.5 0.5 1.18

[.0465]

Figure 4

3. Observe the ratchet adjustment wheel. If a

tighter crimp is required, rotate the adjustment

wheel COUNTERCLOCKWISE to a

higher–numbered setting. If a looser crimp is

required, rotate the adjustment wheel

CLOCKWISE to a lower–numbered setting.

Figure 5

Screw river

Ratchet

A justment

Wheel

Lockscrew

(Typ)

NOTE

408-4354

PRO-CRIMPER III Hand Cr mp ng Tool Assembly 58591-1

of 5Rev

Tyco Electronics Corporation

4. Replace the lockscrew.

5. Make a sample crimp and measure the crimp

height. If the dimension is acceptable, replace and

secure the lockscrew. If the dimension is

unacceptable, continue to adjust the ratchet, and

again measure a sample crimp.

8. MAINTENANCE

Ensure that the tool and dies are clean by wiping

them with a clean, soft cloth. Remove any debris with

a clean, soft brush. Do not use objects that could

damage the tool. When not in use, keep handles

closed to prevent objects from becoming lodged in

the crimping dies, and store in a clean, dry area.

9. VISUAL INSPECTION

The crimping dies should be inspected on a regular

basis to ensure that they have not become worn or

damaged. Inspect the crimp sections for flattened,

chipped, worn, or broken areas. If damage or

abnormal wear is evident, the tool must be replaced.

See Section 10, REPLACEMENT.

10. REPLACEMENT

Customer–replaceable parts are shown in Figure 1.

Available separately, PRO–CRIMPER III Hand

Crimping Tool Repair Kit 679221–1 includes a

replacement nut and a variety of pins, rings, screws,

and springs.

If the dies are damaged or worn excessively, they

must be replaced.

Order the repair kit and replaceable parts through

your Tyco Electronics representative, or call

1–800–526–5142, or send a facsimile of your

purchase order to 1–717–986–7605, or write to:

CUSTOMER SERVICE (38–35)

TYCO ELECTRONICS

PO BOX 3608

HARRISBURG PA 17105–3608

11.REVISION SUMMARY

Since the previous release of this instruction sheet,

the following items have changed:

PRO–CRIMPER II hand tool became

PRO–CRIMPER III hand tool;

TE logo was applied; and

The format was updated to the current

corporate requirements.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Tyco Electronics Crimpwerkzeuge Handbücher

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

Tyco Electronics

Tyco Electronics 1490748-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics AMP PRO–CRIMPER II Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

Tyco Electronics

Tyco Electronics 58532 Series Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO CRIMPER III Bedienungsanleitung

Tyco Electronics

Tyco Electronics ERGOCRIMP 2-1579021-9 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 58613-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 69324-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 2063195-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 58443-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 58571-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 408-10050 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 58605-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

Tyco Electronics

Tyco Electronics 696675-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics PIDG STRATO-THERM Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

Tyco Electronics

Tyco Electronics 58569-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

Tyco Electronics

Tyco Electronics DYNA-CRIMP Bedienungsanleitung

Beliebte Crimpwerkzeuge Handbücher anderer Marken

Panduit

Panduit CT-1000 Administratorhandbuch

JST

JST CS 10 Bedienungsanleitung

molex

molex 63811-5100 Bedienungsanleitung

Danfoss

Danfoss ET4200 Bedienungsanleitung

TE Connectivity

TE Connectivity 2063528-1 Bedienungsanleitung

molex

molex 63825-3000 Bedienungsanleitung

CRH

CRH CRL CBLHCT1 Bedienungsanleitung

Emerson

Emerson Klauke ES 105CFM Bedienungsanleitung

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Bedienungsanleitung

Danfoss

Danfoss ET4350 Bedienungsanleitung

Milwaukee

Milwaukee M18 Bedienungsanleitung

HOGERT

HOGERT HT1P169 Bedienungsanleitung

Textron

Textron ESG105L Bedienungsanleitung

Emerson

Emerson Klauke ES 20RMCCFB Bedienungsanleitung

Continental Refrigerator

Continental Refrigerator PC150HD Bedienungsanleitung

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Bedienungsanleitung

Emerson

Emerson Klauke ES 105CFB Bedienungsanleitung

TE Connectivity

TE Connectivity 539 726-2 Bedienungsanleitung