Tyco Electronics PRO- CRIMPER III Bedienungsanleitung

Instruction Sheet

PRO- CRIMPER* III Hand

Crimping Tool Assembly 91337- 1 408--8378

LOC B

1of 5

E2009 Tyco Electronics Corporation, Harrisburg, PA

All International Rights Reserved

TE logo and Tyco Electronics are trademarks.

*Trademark. Other products, logos, and company names used are the property of their respective owners.

TOOLING ASSISTANCE CENTER 1--800--722--1111

PRODUCT INFORMATION 1--800--522--6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.tycoelectronics.com

23 JUL 09 Rev Awith Die Assembly 91337- 2

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume

applications. A wide selection of powered application equipment for extended--use, production operations is available.

The PRO--CRIMPER III Hand Crimping Tool is a “Commercial” grade tool

and is designed primarily for field installation, repair, maintenance work, or

prototyping in industrial, commercial, or institutional applications. Product

crimped with this tool will meet the crimp height requirement for hand tools in

the appropriate 114 series specification, but may not comply with other feature

parameters of the specification. Tyco Electronics offers a variety of tools to

satisfy your performance requirements. For additional information, contact the

Tooling Assistance Center at 1--800 --722--1111.

Locator Assembly

(Supplied with

Die Assembly)

Front of Tool

(Locator Side)

Die Assembly

Moving Jaw

Ratchet Adjustment Wheel

Moving Handle

Stationary Handle

Pivot Pin

Back of Tool

(Wire Side)

Stationary Jaw

PRO--CRIMPER III Hand

Crimping Tool Frame

354940--1 (408--9930)

Wire

TE Die

Assembly

Locator

Assembly{

Product

Family}Size

(AWG)

Insulation

Diameter (Max.) Strip Length

18 2.54 [.100]

[

]

91337--2 58515--1 Size 16 Contacts 16--14 3.18 [.125] 3.81 [.150

]

{Supplied with die assembly. Also available separately.

}Contact the Tooling Assistance Center or Product Information (at the numbers listed below) for specific contact part numbers.

Figure 1

1. INTRODUCTION

PRO--CRIMPER III Hand Crimping Tool Assembly

91337--1 consists of Die Assembly 91337--2 and

PRO--CRIMPER III Hand Tool Frame 354940--1. The

die assembly consists of crimping dies and a locator

assembly.

Read these instructions thoroughly before crimping

any contacts.

All dimensions on this document are in

millimeters [with inches in brackets]. Figures are

not drawn to scale.

Reasons for revision are listed in Section 10,

REVISION SUMMARY.

2. DESCRIPTION

The tool features a tool frame with a stationary jaw

and handle, moving jaw, moving handle, and

adjustable ratchet that ensures full contact crimping.

The tool frame holds a die assembly with two

crimping chambers. See Figure 1.

The die assembly features a wire anvil, insulation

anvil, wire crimper, and insulation crimper.

NOTE

408- 8378

PRO- CRIMPER III Hand Crimping Tool Assembly 91337- 1

Rev A2 of 5 Tyco Electronics Corporation

Locator

Assembly

Figure 2

Short Die Retaining

Screw

Long Die Retaining

Screw

Die Retaining

Pins (4)

Tool Frame

Nut

Contact

Locator

Chamfered

Edge (Typ)

Wire Crimper

Wire Anvil

Insulation

Anvil

Insulation

Crimper

Chamfered

Edge (Typ)

Markings Face

Outward (Typ)

Die retaining pins and die retaining screws are used

to position and secure the dies in the tool frame.

Attached to the outside of the frame is a locator

assembly, which contains a locator and contact

retainer. A nut is used on the upper die retaining

screw to hold the locator assembly in place.

3. INSTALLATION AND REMOVAL OF DIE ASSEMBLY

AND LOCATOR ASSEMBLY (Figure 2)

1. Open the tool handles, and remove the two die

retaining screws from the tool jaws.

2. Place the wire anvil and insulation anvil so that

the chamfered sides and marked surfaces face

outward, when mounted in the moving jaw of the

tool frame.

3. Insert two die retaining pins through the tool

frame and into the anvils.

4. Insert the short die retaining screw through the

jaw and through both anvil dies, and tighten the

screw just enough to hold the dies in place. Do not

tighten the screw completely at this time.

5. Place the wire crimper and insulation crimper so

that their chamfered sides and their marked

surfaces face outward, when mounted in the

stationary jaw of the tool frame.

6. Insert two die retaining pins through the tool

frame and into the crimpers.

7. Insert the long die retaining screw through the

jaw and through both crimper dies, and tighten the

screw just enough to hold the dies in place. Do not

tighten the screw completely at this time.

8. Carefully close the tool handles, making sure

that the anvils and crimpers align properly.

Continue closing the tool handles until the ratchet

in the tool frame has engaged sufficiently to hold

the anvils and crimpers in place, then tighten both

die retaining screws.

9. Place the locator assembly over the end of the

long die retaining screw. Position the locator

assembly against the side of the tool jaw.

10. Place the nut onto the end of the long screw

and tighten the nut enough to hold the locator

assembly in place, while still allowing the locator to

slide up and down.

11. To disassemble, close the tool handles until the

ratchet releases, remove the nut, the locator

assembly, the two die retaining screws, and the

four die retaining pins, and slide the anvils and

crimpers out of the tool jaws.

4. CRIMPING PROCEDURE

This tool is provided with a crimp adjustment

feature. Initially, the crimp height should be

verified as specified in Section 5, CRIMP

HEIGHT INSPECTION, and Section 6,

RATCHET (Crimp Height) ADJUSTMENT, before

using the tool to crimp desired contacts.

NOTE

408- 8378

PRO- CRIMPER III Hand Crimping Tool Assembly 91337- 1

3of 5Rev ATyco Electronics Corporation

refer to Figure 1, and select wire of the specified size

and insulation diameter. Strip the wire to the length

indicated, taking care not to nick or cut wire strands.

Select an applicable contact and identify the

appropriate3e crimping chamber according to the wire

size markings on the tool.

Refer to Figure 3, and proceed as follows:

1. Hold the tool so that the front (locator side) is

facing you. Squeeze tool handles together and

allow them to open fully.

2. Insert the contact—mating end first—into the

appropriate crimping chamber. Make sure that the

open “U” of the wire barrel and insulation barrel

face the stationary jaw.

3. Make sure that the wire stop enters the contact

wire stop slot between the wire barrel and contact

shoulder.

Make sure that both sides of the contact

insulation barrel are started evenly into the

crimping chamber. Do NOT attempt to crimp an

improperly positioned contact.

4. Hold the contact in position, and squeeze the

tool handles together until ratchet engages

sufficiently to hold the contact in position. Do NOT

deform insulation barrel or wire barrel.

5. Insert stripped wire into contact insulation and

wire barrels until it is butted against the wire stop,

as shown in Figure 3.

6. Holding the wire in place, squeeze tool handles

together until ratchet releases. Allow tool handles

to open and remove crimped contact.

The crimped contact may stick in the crimping

area, but can be removed by pushing downward

on the top of the locator (see Figure 3).

7. Check the contact crimp height as described in

Section 5, CRIMP HEIGHT INSPECTION. If

necessary, adjust the crimp height as described in

Section 6, RATCHET (Crimp Height)

ADJUSTMENT.

5. CRIMP HEIGHT INSPECTION

Crimp height inspection is performed through the use

of a micrometer with a modified anvil, commonly

referred to as a crimp--height comparator. Tyco

Electronics does not manufacture or market

crimp--height comparators. Detailed information on

obtaining and using crimp--height comparators can be

found in instruction sheet 408--7424.

To measure the crimp height:

1. Refer to Figure 4 and select a wire (maximum

size) for each crimp section listed in the table.

2. Crimp the contact(s) according to the

procedures provided in Section 4, CRIMPING

PROCEDURE.

3. Using the crimp height comparator, measure the

wire barrel crimp height as shown in Figure 4. If the

crimp height conforms to the dimensions provided

in Figure 4, then the tool is considered

dimensionally correct. If the crimp height does not

conform to the dimensions provided, the tool must

be adjusted. Refer to Section 6, RATCHET (Crimp

Height) ADJUSTMENT.

Figure 3

Wire Strip Length

Locator in Contact

Wire Stop Slot Wire Inserted to

Locator Wire Stop

Tool Stationary Jaw

Locator

Wire

Contact

CAUTION

NOTE

408- 8378

PRO- CRIMPER III Hand Crimping Tool Assembly 91337- 1

Rev A4 of 5 Tyco Electronics Corporation

Position Point on

Center of Wire

Barrel Opposite

Seam

“A”

+.05

+[.002]

Modified

Anvil

Wire Size

AWG (Max.)

Crimp Section

Marking

Crimp Height

Dimension “A”

18 18 1.37 [.054]

14 14 1.55 [.061]

Figure 4

6. RATCHET (Crimp Height) ADJUSTMENT (Figure 5)

1. Remove the lockscrew from the ratchet

adjustment wheel.

2. With a screwdriver, adjust the ratchet wheel

from the locator side of the tool.

3. Observe the ratchet adjustment wheel. If a

tighter crimp is required, rotate the adjustment

wheel counterclockwise to a higher--numbered

setting. If a looser crimp is required, rotate the

adjustment wheel clockwise to a lower--numbered

setting.

4. Re--assemble the lockscrew.

5. Make a sample crimp and measure the crimp

height. If the dimension is unacceptable, continue

to adjust the ratchet, and again measure a sample

crimp.

7. MAINTENANCE

Ensure that the tool and dies are clean by wiping

them with a clean, soft cloth. Remove any debris with

a clean, soft brush. Do not use objects that could

damage the tool. When not in use, keep handles

closed to prevent objects from becoming lodged in

the crimping dies, and store in a clean, dry area.

Figure 5

Screwdriver

Ratchet Adjustment

Wheel

Lockscrew

(Typ)

8. VISUAL INSPECTION

The crimping dies should be inspected on a regular

basis to ensure that they have not become worn or

damaged. Inspect the crimping chambers for

flattened, chipped, worn, or broken areas. If damage

or abnormal wear is evident, the tool must be

replaced. See Section 9, REPLACEMENT AND

REPAIR.

9. REPLACEMENT AND REPAIR

Customer--replaceable parts are shown in Figure 1.

Available separately, PRO--CRIMPER III Hand

Crimping Tool Repair Kit 679221--1 includes a

replacement nut and a variety of pins, rings, screws,

and springs.

If the dies are damaged or worn excessively, they

must be replaced.

Order repair kit and replaceable parts through your

representative, or call 1--800--526--5142, or send a

facsimile of your purchase order to 717--986--7605, or

write to:

CUSTOMER SERVICE (38--35)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

HARRISBURG PA 17105--3608

10. REVISION SUMMARY

Revisions to this instruction sheet include:

SPRO--CRIMPER II Hand Tool change to

PRO--CRIMPER III Hand Tool;

SCrimp--height comparator information revision;

STE logo application;

SDocument format update; and

SAddition of back page (tools using 91337--2).

408- 8378

PRO- CRIMPER III Hand Crimping Tool Assembly 91337- 1

5of 5Rev ATyco Electronics Corporation

Dies 91337-2 May Also Be Used with the Following Tools.

PRO-CRIMPER III Hand Tool 354940- 1

(Instruction Sheet 408-9930)

SDE PEW- 12 Hand Tool 9-1478240-0

(Instruction Sheet 408-8851)

SDE Bench Terminator 1490076- 2

(Customer Manual 409-10052)

626 Adapter 679304-1

(Instruction Sheet 408-4070)

Battery Tool (Shouldered Die) 1725837-1, - 2

(Customer Manual 409-10053)

Battery Tool (Pin Die) 1213890- 1, - 2

(Customer Manual 409-10065)

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

TE Connectivity:

91337-1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Tyco Electronics Crimpwerkzeuge Handbücher

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

Tyco Electronics

Tyco Electronics 58532 Series Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

Tyco Electronics

Tyco Electronics 46121 Bedienungsanleitung

Tyco Electronics

Tyco Electronics AMP 91907 Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

Tyco Electronics

Tyco Electronics 90430-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

Tyco Electronics

Tyco Electronics 1490748-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics CERTI-CRIMP II Bedienungsanleitung

Tyco Electronics

Tyco Electronics PIDG Series Bedienungsanleitung

Tyco Electronics

Tyco Electronics 69156-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 90035-3 Bedienungsanleitung

Tyco Electronics

Tyco Electronics SOLARLOK 1579004-9 Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III 58517 Series Bedienungsanleitung

Tyco Electronics

Tyco Electronics 3-1579002-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

Tyco Electronics

Tyco Electronics 2-231652-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

Tyco Electronics

Tyco Electronics 90301-2 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 1901820-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

Beliebte Crimpwerkzeuge Handbücher anderer Marken

Panduit

Panduit CT-1000 Administratorhandbuch

JST

JST CS 10 Bedienungsanleitung

molex

molex 63811-5100 Bedienungsanleitung

Danfoss

Danfoss ET4200 Bedienungsanleitung

TE Connectivity

TE Connectivity 2063528-1 Bedienungsanleitung

molex

molex 63825-3000 Bedienungsanleitung

CRH

CRH CRL CBLHCT1 Bedienungsanleitung

Emerson

Emerson Klauke ES 105CFM Bedienungsanleitung

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Bedienungsanleitung

Danfoss

Danfoss ET4350 Bedienungsanleitung

Milwaukee

Milwaukee M18 Bedienungsanleitung

HOGERT

HOGERT HT1P169 Bedienungsanleitung

Textron

Textron ESG105L Bedienungsanleitung

Emerson

Emerson Klauke ES 20RMCCFB Bedienungsanleitung

Continental Refrigerator

Continental Refrigerator PC150HD Bedienungsanleitung

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Bedienungsanleitung

Emerson

Emerson Klauke ES 105CFB Bedienungsanleitung

TE Connectivity

TE Connectivity 539 726-2 Bedienungsanleitung