Tyre ?are T650 Bedienungsanleitung
Instruction Manual
Wireless tire pressure and temperature
monitoring system
1. Product introduction…………………………………………..
Introduction(LCD display description )………….
2.Factory settings………………………………………………….…
3.Parameters setting………………………………………….…….
· Pressure unit setting....................................................................
· Temperature unit setting............................................................
· Pressure alarm value setting.....................................................
· Temperature alarm value setting.............................................
· Tire matching setting...................................................................
·Interchange tire setting...............................................................
4.Function ……………………………………………………..…............
5.Internal sensor installation……….……………….......…..
6.Internal sensor parameter……………………....……….…
7.Notice and statement.........................................................
01
02
03
04
05
05
06
08
08
09
10
12
16
17
Contents
U901T 出厂设置
1.Product introduction
0101
Monitor Solar panel
USB interface
Button positions
“ -” :Press and hold the - button to turn on or turn off.Select function.
“SET”:Press and hold the SET button to enter setting mode or
save and exit to standby after finish setting.
:Selection button.
Buttons:
“+”
Icon and description
Matching sensor with monitor
Temperature unit(℃ or ℉）
Pressure unit(BAR or PSI)
Press and hold the - button for 3-6s to turn on.
Press and hold the - button for 3-6s to turn off.
Exchange tire location
Monitor battery display
Introduction(LCD display description)
02
Solar energy charging(Display while sunlight
exposure to solar panel )
Abnormal alarm(Alerts when tire pressure,
temperature,sensor battery is abnormal)
ON
OFF
产品介绍2.Factory settings
03
Default Parameters：
BAR/PSI
6.0BAR(87PSI)
4.0BAR(58PSI)
℃/℉
65℃/149℉
Pressure Unit
High Pressure
Low Pressure
Temperature Unit
Temperature alarm value
Relationship among pressure units PSI,kg/cm²,kPa and BAR
1BAR=14.503PSI 1BAR=1.0197 kg/cm2 1BAR=100kPa
Changing Parameters：
Press and hold SET for 3s to enter the factory setting mode,
There are 6 groups of settings that can be reset,as follows:
1. Pressure unit setting
2.Temperature unit setting
3.Pressure alarm value setting
5.Tire matching setting
6.Interchange tire setting
4.Temperature alarm value setting
3.Parameters setting
04
Tire pressure alarm value setting
The tires in monitor interface are divided into two axles as follows:
The tire numbers(01.02,03,04,05,06)
represent the tire position where the sensor is located.
First axle
Second axle
①②
⑤
③ ④
⑥
01.Front tire of the first axle 02.Right tire of the first axle
03.Left-inside tire of the second axle 04.Right-inside tire of the second axle
05.Left-outside tire of the second axle 06.Right-outside tire of the second axle
TIRE LOCATIONS
Parameters setting
05
Pressure unit setting
In the standby interface,press and hold SET to enter into the setting mode,
press + to select to "BAR PSI" interface ,press SET then press + or - to select
pressure unit you want. And press the SET to confirm setting,finally press and
hold SET for 3 seconds to save the setting and exit to standby.
Temperature unit setting
In the standby interface,press and hold SET to enter into the setting mode,
press + to select to "℃ ℉" interface ,press SET then press + or - to select
pressure unit you want. And press the SET to confirm setting,finally press
and hold SET for 3 seconds to save the setting and exit to standby.
Pressure unit setting interface
Temperature unit setting interface
Parameters setting
06
High pressure alarm value setting of
the first axle
In the standby interface,press and hold SET to enter into the setting mode.
Press + to select to setting interface "HI"on first axle as below. Press SET then
press + or - to select high pressure alarm value you want. And press SET to
confirm setting ,finally press and hold SET for 3 seconds to save the setting
Low pressure alarm value setting of
the first axle
In the standby interface,press and hold SET to enter into the setting mode.
Press + to select to setting interface "LO"on first axle as below.Press SET then
press + or - to select low pressure alarm value you want. And press SET to
confirm setting ,finally press and hold SET for 3 seconds to save the setting
and exit to standby.
High pressure alarm value setting interface of the first axle
Low pressure alarm value setting interface of the first axle
Parameters setting
07
High pressure alarm value setting of
the second axle
In the standby interface,press and hold SET to enter into the setting mode.
Press + to select to setting interface "HI" on second axle as below.Press SET
then press + or - to select high pressure alarm value you want. And press SET
to confirm setting ,inally press and hold SET for 3 seconds to save the setting
and exit to standby.
Low pressure alarm value setting of
the second axle
In the standby interface,press and hold SET to enter into the setting mode.
Press + to select to setting interface "LO" on second axle as below .Press SET
then press + or - to select low pressure alarm value you want. And press SET
to confirm setting ,finally press and hold SET for 3 seconds to save the setting
High pressure alarm value setting interface of the second axle
Low pressure alarm value setting interface of the second axle
Parameters setting
08
High temperature alarm value setting
In the standby interface,press and hold SET to enter into the setting mode.
Press + to select to setting interface "HI" as below.Press SET then press + or -
to select high temperature alarm value you want. And press SET to confirm
setting ,finally press and hold SET for 3 seconds to save the setting
High temperature alarm value setting interface
Tire matching
In the standby interface,press and hold SET to enter into the setting mode.
Press + to select to setting interface " ". Press SET then press + or - to select
the tire position to be matched,and then install the corresponding sensor.
【External sensor operation】 Mount the sensor to the corresponding tire.
【Built-in sensor operation】Installl the built-in sensor and inflate the
corresponding tire.
Tire matching operation interface
Monitor will display the corresponding value after installing
sensors,means match successfully. Finally press and hold the
SET to save and exit to standby.
Inhaltsverzeichnis
Andere Tyre ?are Messgerät Handbücher
