Tyre ?are T802C Bedienungsanleitung

Contents
1.
Cautions
..................................................................................................................................... 1
2.
Components
................................................................................................................2
2.1 Components.......................................................................................................... 2
2.2 Monitor and icons ................................................................................................ 2
3. Functions and
features
..................................................................................................3
4 . Monitor
........................................................................................................................4
5. Parameter
settings
.......................................................................................................6
6.
Alarm status
...............................................................................................................11
.
Troubleshooting guide
................................................................................................13

1. Cautions
1.1 Sa ety cautions
Before installing this product, please read the cautions below.
1. The monitor should be installed inside the vehicle where it does not affect normal
driving.
2. The monitor should be fixed in such a way that it does not fall off while you are
driving.
3. After the sensor has been installed, check if there is any air leakage. If necessary,
smear the tyre valve with soapy water to check whether there is air leakage.
4. Be careful: tyre blowout can be caused by high pressure and fuel consumption can
be affected by by low pressure.
5. This product can effectively monitor the tyre pressure and temperature in real
time, but cannot prevent traffic accidents, so it's also important to choose high
quality tyres and ensure normal tyre pressure when using this product.
6. Pay attention to the traffic when checking the tyre pressure and temperature while
driving.
1.2 Installation cautions
1. The sensor and receiver are wirelessly connected over a long distance. A number of
anti-jamming functions ensure that the receiver still effectively receive the data
when used with a long vehicle .
2. Due to expansion and contraction of the air in the tyre, it is normal for the tyre
pressure to fluctuate while driving.
3. It is normal for a tyre to have some air leakage, with no direct relation to the
installation of this product.
It is recommend that you install the monitor and power it up before installing the
sensor.
The four default sensors have already been matched with the monitor in the
factory. There is no need to match the sensors again.
1


3. Functions and eatures
3.1 Main unction
This product is mainly used to monitor the pressure and temperature of tyres
automatically while driving, and to alert the driver to danger, such as rapid air leakage,
low/high pressure, and high temperature.
The wireless tyre pressure monitoring system is the only effective way to monitor the
tyre pressure at all times. It:
•ensures safe driving
•saves fuel
•prolongs the lifetime of tyres
•provides real-time monitoring of tyre pressure
3.2 Product eatures
1. Graphic user inter ace
The display of pressure and temperature on the monitor allows the user to keep track of
the condition of the tyres at all times.
2. High accuracy
The product uses electronic pressure detection, where the accuracy of tyre pressure can
be ±1 PSI.
3. Abnormal status alert
During driving, if the tyre pressure is lower or higher than the preset value, or if there is
rapid air leakage, the monitor will receive and display the alert immediately.
4. Lightweight sensor
The special design of the sensor means that it will not affect the appearance of the tyre.
3

4. Monitor
4.1 Monitor eatures
•The alarm range can be set.
•Easy to operate tyre exchange function.
•Several ways the monitor can be placed and installed.
•The data for all the tyres are shown on the same screen.
•Option of pressure unit (PSl, BAR)
•Automatic power on or off function.
•Heat-resistant battery.
•Solar energy charge function.
•Wide angle screen design.
•Long-life battery. Charge the monitor for 3 hours at an electrical outlet using the
USB cable when the monitor is dead or at 1 bar battery life.
•Adjustable backlight brightness (press + or - to adjust).
4.2 Installation instructions
With anti-skidding design and randomly placed products
Note:
•The monitor should be positioned so that it does not affect the driver's vision.
•The monitor should be fixed in such a way that it does not fall off during driving.
•Please be careful when you check the pressure and temperature on the monitor
during driving.
•The tyre pressure and temperature are monitored automatically. The driver does
not have to make any changes to the monitor while driving.
4

Monitor
Monitor speci ications
Input voltage DC 5V
Storage temperature - 30 °C to + 85 °C
Working temperature - 20 °C to + 80 °C
Frequency 433.92 MHz
Size 88*68*25 (l*w*h)
Mass 5 g
4.3 Automatic power on/manual power on
When the car stops for more than 5 minutes and the monitor is not being charged, the
monitor will automatically enter into sleep mode. The monitor will not receive any data
from the sensor, but it will become active when car is moving again.
The user can also switch the monitor on or off manually.
•Press the - button for 6 seconds to switch on the monitor.
•Press the - button for 6 seconds to switch off the monitor.
•The monitor will automatically switch off when the battery is low.
5

5.Parameter settings
5.1 Factory de ault settings
Pressure unit BAR
High pressure 3.0 BAR (44 PSI)
Low pressure 2.0 BAR (29 PSI)
Temperature unit °C
High temperature 65°C
Relationship between pressure units PSI, kg/cm2, kPa and BAR
1 BAR = 14 .503 PSI 1 BAR = 10 19 kg/cm2 1 BAR = 100 kPa
5.2 System parameter settings
Press and hold the selection button ( ) for 5 seconds to enter into T802 system
parameter setting mode. The system has six setting modes.
1. Pressure unit setting 4. High temperature setting
2. High pressure setting 5. Tyre matching setting
3. Low pressure setting 6. Tyre interchange setting
Setting sequence
1. Pressure unit setting
Enter into parameter setting mode, press + or - to select the pressure unit setting
(Figure 5-1-1), then press the selection button to change the pressure unit setting. Press
+ or - to select the pressure unit, then press the selection button to confirm and save
the change. Press + to go to the next setting or press the selection button for 3 seconds
to exit the setting mode.
Fig 5-1-1
1. Enter into parameter setting mode 2. Press to change setting
3. Press + or - to select unit 4. Press and hold to save and exit
6

Parameter settings
2. High pressure setting
Enter into parameter setting mode, press + or - to select high pressure setting
(Figure 5-1-2), then press the selection button to change the high pressure setting.
Press + or - to adjust the high pressure setting, then press the selection button to
confirm and save the change. Press + to go to the next setting or press the selection
button for 3 seconds to exit the setting mode.
Fig 5-1-2
1. Enter into parameter setting mode 2. Press + or - to select high pressure mode
3. Press to change setting 4. Press + or - to select adjust value
5. Press and hold to save and exit
3. Low pressure setting
Enter into parameter setting mode, press + or - to select low pressure setting
(Figure 5-1-2), then press the selection button to change the low pressure setting.
Press + or - to adjust the low pressure setting, then press the selection button to
confirm and save the change. Press + to go to the next setting or press the selection
button for 3 seconds to exit the setting mode.
Fig 5-1-3
1. Enter into parameter setting mode 2. Press + or - to select low pressure mode
3. Press to change setting 4. Press + or - to select adjust value
5. Press and hold to save and exit

Parameter settings
4. High temperature setting
Enter into parameter setting mode, press + or - to select high temperature setting
(Figure 5-1-4), then press the selection button to change the high temperature setting.
Press + or - to adjust the setting, then press the selection button to confirm and save
the change. Press + to go to the next setting or press the selection button for 3 seconds
to exit the setting mode.
Fig 5-1-4
1. Enter into parameter setting mode 2. Press + or - to select high temperature mode
3. Press to change setting 4. Press + or - to select adjust value
5. Press and hold to save and exit
5. Tyre match setting (use when sensors need to be replaced)
Enter into parameter setting mode, press + or - to select tyre match setting (Figure 5-2-
1), then press the selection button to change tyre match setting(Figure 5-2-2).
Press + or - to select the tyre location.
External sensor operation: Mount the external sensor to the corresponding tyre.
Internal sensor operation: Mount the internal sensor and inflate the corresponding
tyre.
When the sensor has detected the tyre pressure, it will send the data to the monitor.
The monitor will indicate ON (Figure 5-2-2) and the tyre is matched. After matching all
the tyres, press the selection button to confirm and save the change. Press + to go to
the next setting or press the selection button for 3 seconds to exit the setting mode .
Fig 5-2-1
1. Enter into parameter setting mode 2. Press + or - to select tyre match mode
3. Press to change setting 4. Press + or - to select the desired tyre
8
Inhaltsverzeichnis
Andere Tyre ?are Messgerät Handbücher



















