Ubiquiti AirMAX NanoBridge M NBM3 Bedienungsanleitung

High-Performance

airMAX™Bridge

Model: NBM3/NBM365/NBM900

Introduction

Thank you for purchasing the Ubiquiti Networks™

NanoBridge™. This Quick Start Guide is designed to guide

you through the installation and show you how to access

the airOS™Configuration Interface. This Quick Start Guide

also includes the warranty terms and is for use with the

NanoBridge, models NBM3, NBM365, and NBM900.

Package Contents

or or

Dish Reflector NanoBridge

M3/M365

or NanoBridge

M900

M3/M365 Feed

Support Tube

or M900 Feed

Support Tube

Dish Bracket Mounting

Bracket

Pole Clamps

(Qty. 2)

U-Bolt

(M8, Qty. 2)

M8x50

Carriage Bolt

M8x15 Carriage

Bolts (Qty. 4)

M8 Flange Nuts

(Qty. 9)

M6x15

Carriage Bolt

M6x12 Carriage

Bolts (Qty. 4)

High-Performance

airMAX™Bridge

Model:NBM3/NBM365/NBM900

M6 Flange Nut

(Qty. 5)

Plastic Straps

(Qty. 2)

PoE Adapter

(24V, 0.5A)

Power Cord Quick Start

Guide

Products may be different from pictures and are subject to change without notice.

cable and earth grounding must be used as conditions of product warranty. TOUGHCable is

designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Hardware Overview

NBM3/NBM365 Ports

Secondary Main

Reset

Secondary Port This 10/100 Ethernet port is used for

bridging.

Main Port This 10/100 Ethernet port is used to connect the

power and should be connected to the LAN and DHCP server.

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the NanoBridge is

already poweredon.

NBM900 Ports

RP-SMA LAN Reset

RP-SMA Connector Reserved for future use.

LAN Port The 10/100 Ethernet port is used to connect the

power and should be connected to the LAN and DHCP server.

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the NanoBridge is

already poweredon.

NBM3/NBM365 LEDs

LAN2LAN1

Power The Power LED will light green when

the device is connected to a power source.

LAN1 Main The LAN1 Ethernet LED will light steady

green when an active Ethernet connection is

made to the Main Port and flash when there

is activity.

LAN2

Secondary The LAN2 Ethernet LED will

light steady green when an active Ethernet

connection is made to the Secondary Port and

flash when there isactivity.

Signal In airOS, you can modify the wireless

signal strength threshold values for each

LED on the Advanced tab under Signal LED

Thresholds. The default values are shown below:

LED will light red when the wireless

signal strength is above -94 dBm.

LED will light amber when the wireless

signal strength is above -80 dBm.

LED will light green when the wireless

signal strength is above -73 dBm.

LED will light green when the wireless

signal strength is above -65 dBm.

*720-00064-01*

720-00064-01

NBM900 LEDs

Power The Power LED will light green when

the device is connected to a power source.

Ethernet The Ethernet LED will light steady

green when an active Ethernet connection is

made and flash when there is activity.

Signal In airOS, you can modify the wireless

signal strength threshold values for each

LED on the Advanced tab under Signal LED

Thresholds. The default values are shown below:

LED will light red when the wireless

signal strength is above -94 dBm.

LED will light amber when the wireless

signal strength is above -80 dBm.

LED will light green when the wireless

signal strength is above -73 dBm.

LED will light green when the wireless

signal strength is above -65 dBm.

Installation Requirements

• 10 mm wrench

• 13 mm wrench

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial-grade shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Using the Correct Feed Support Tube

The NanoBridgeM3/M365 and NanoBridgeM900 require

different Feed Support Tubes, which are not interchangeable.

Ensure that you are using the correct Feed Support Tube for

your NanoBridge model before you begin installation.

NBM3/M365 Feed Support Tube NBM900 Feed Support Tube

Installation

The installation instructions show the NBM900; however, the

same instructions apply to the NBM3 and NBM365.

1. Attach the Feed Support Tube to the Dish Bracket using the

M8x50 Carriage Bolt, M8 Serrated Flange Nut, M6x15 Carriage

Bolt, and M6 Serrated Flange Nut.

2. Attach the Dish Bracket to the Dish Reflector using the four

M6x12 Carriage Bolts and four M6 Flange Nuts.

3. Attach the Mounting Bracket to the Dish Bracket using the

four M8x15 Carriage Bolts and four M8 Flange Nuts.

4. Install the NanoBridge by lining up the mounting tabs of

the NanoBridge with the slots on the Feed Support Tube.

Then slide the NanoBridge into place.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Netzwerk-Hardware Handbücher

Ubiquiti

Ubiquiti ER-4 Bedienungsanleitung

Ubiquiti

Ubiquiti UF-Instant Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi NVR Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam airMAX NBE-M5-300 Bedienungsanleitung

Ubiquiti

Ubiquiti UBB Bedienungsanleitung

Ubiquiti

Ubiquiti USW-24 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam M Bedienungsanleitung

Ubiquiti

Ubiquiti uFiber OLT 4 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Dream Machine Pro Bedienungsanleitung

Ubiquiti

Ubiquiti UF-OLT-4 Bedienungsanleitung

Ubiquiti

Ubiquiti Loco5AC Bedienungsanleitung

Ubiquiti

Ubiquiti UF-Instant Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-M5-300-IS Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam AC Gen 2 Bedienungsanleitung

Ubiquiti

Ubiquiti RocketM Series Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-500 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-24-250W Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-24-250W Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USW-Flex-Mini Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi LED ULED-AT Bedienungsanleitung

Ubiquiti

Ubiquiti PBE-5AC-GEN2-5-EU Bedienungsanleitung

Ubiquiti

Ubiquiti UF-Instant Bedienungsanleitung

Ubiquiti

Ubiquiti airMAX NanoStationM2 Bedienungsanleitung

Ubiquiti

Ubiquiti Airmax NBE-M2-400 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung

Ubiquiti airMAX NanoBridge M NBM3 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken