Ubiquiti PowerBeam PBE-5AC-500 Bedienungsanleitung

High-Performance

Integrated InnerFeed®

airMAX®ac Bridge

Model: PBE-5AC-500

Introduction

Thank you for purchasing the Ubiquiti Networks® PowerBeam®.

This Quick Start Guide is designed to guide you through

installation and includes warranty terms.

Package Contents

Reflector Radome Antenna Feed Rear Housing

Mounting

Bracket

Adjustment

Bracket

Hex Bolts with Washers

(Qty. 4)

Pole Clamp

(Qty. 2)

Carriage Bolts

(Qty. 4)

Flange Nuts

(Qty. 4)

Screws with Washers

(Qty. 4)

Washers

(Qty. 4)

High-Performance

IntegratedInnerFeed®

airMAX®acBridge

Model:PBE-5AC-500

Nylon Insert

Lock Nuts

(Qty. 4)

Gigabit PoE (24V, 0.5A)

with Mounting Bracket

Power Cord Quick Start

Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™ is

designed for outdoor installations. It is the professional installer’s responsibility to follow local

country regulations, including operation within legal frequency channels, output power, and

Dynamic Frequency Selection (DFS) requirements.

Hardware Overview

Bottom View

Technology

Cable Door

Rear Housing

Ethernet Port

Release

Button Slot

Mounting Bracket

Release Button

Reflector

Alignment Pins

Reset Button

Antenna Feed

Radome

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the PowerBeam

is poweredon. Alternatively, the PowerBeam may be reset

remotely via a Reset button located on the bottom of the

Gigabit PoE adapter.

Release Button After you assemble the PowerBeam, check

the Release button; it should be fully engaged in the Release

Button Slot of the Rear Housing. This ensures that the Antenna

Feed is locked into place. If you need to remove the Antenna

Feed, you must depress the Release button first.

LEDs

Power The Power LED will light blue when the

device is connected to a power source.

Ethernet The Ethernet LED will light steady blue

when an active Ethernet connection is made and

flash when there is activity.

Signal In airOS®, you can modify the threshold

value for the wireless signal strength LEDs on the

Wireless tab under Signal LED Thresholds. Each LED

will light when the wireless signal strength is equal

to or greater than the LED’s threshold value. The

default threshold values for these LEDs are shown

below:

-65 dBm -73 dBm -80 dBm -94 dBm

Application Examples

The PowerBeam mounted outdoors with the Dish Reflector

installed provides directional outdoor coverage (gain is

reflector‑dependent).

The PowerBeam mounted outdoors without the Dish Reflector

installed provides outdoor‑to‑indoor coverage using the 3 dBi

Antenna Feed only.

Installation Requirements

• 13 mm wrench

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial‑grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Installation

1. Align and insert the tabs of the Mounting Bracket into

the slots of the Reflector. Rotate the Mounting Bracket

counterclockwise until the alignment holes in the dish and

bracket align with each other.

2. Remove the Antenna Feed from the Rear Housing:

a. Push in the sides of the Cable Door and detach it from

the Rear Housing. Keep the Cable Door detached.

b. Press the Release Button and slide the Rear Housing off

of the Antenna Feed.

3. For added support in high‑wind environments, insert four

Screws with Washers into the holes of the Reflector and

Mounting Bracket, and secure each screw with a Washer

and a Nylon Insert Lock Nut.

Mounting Bracket Reflector

4. Line up the Alignment Pins of the Rear Housing with the

alignment holes of the Mounting Bracket. Push the Rear

Housing into the Mounting Bracket.

5. View the Reflector from the front. Ensure that the three

hooks (indicated below) of the Rear Housing are fully

engaged with the inner wall of the Reflector and locked

into place.

IMPORTANT: Before proceeding, lightly pull the Rear

Housing to confirm that it is locked into place.

6. Attach the Antenna Feed.

a. Insert the Antenna Feed into the Rear Housing, and push

until it locks into place with a click.

b. Lightly pull the Antenna Feed to ensure that it is locked

into place and the Release Button is fully engaged.

Release Button

Bottom View

7. Connect an Ethernet cable to the Ethernet Port of the

Antenna Feed. Then re‑attach the Cable Door.

8. Attach the Pole Clamps to the Adjustment Bracket.

a. Hold the Adjustment Bracket with its clamps facing you

and the Elevation Indicators towards the top.

b. Insert the Carriage Bolts through the holes of the

Adjustment Bracket.

c. Place the Pole Clamps on the bolts on one side of the

bracket by sliding the hole of the clamp over the bolt.

d. Place one Flange Nut on each bolt.

Elevation

Indicator

9. Mount the Adjustment Bracket on the pole and secure it.

a. Place the Adjustment Bracket against the pole.

b. Slide the slot of each Pole Clamp over each Carriage Bolt.

c. Tighten the Flange Nuts on the bolts to 25 N·m to

secure the Adjustment Bracket to the pole.

25 N ·m

Note: The mounting assembly can accommodate a

Ø 40 ‑ 80 mm pole.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Netzwerk-Hardware Handbücher

Ubiquiti

Ubiquiti PowerBeam M5 PBE-M5-400 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-M5-300-IS Bedienungsanleitung

Ubiquiti

Ubiquiti Nano G Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-48-500W Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi NVR Bedienungsanleitung

Ubiquiti

Ubiquiti UBB Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Cloud Key Gen2 Plus Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam AC Gen 2 Bedienungsanleitung

Ubiquiti

Ubiquiti mPort-S mPort Serial Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam airMAX NBE-M5-300 Bedienungsanleitung

Ubiquiti

Ubiquiti UBI-POWERBEAM-M5-300 Bedienungsanleitung

Ubiquiti

Ubiquiti Loco5AC Bedienungsanleitung

Ubiquiti

Ubiquiti PBE-5AC-GEN2-5-EU Bedienungsanleitung

Ubiquiti

Ubiquiti M900 Bedienungsanleitung

Ubiquiti

Ubiquiti UF-Instant Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-500-ISO Bedienungsanleitung

Ubiquiti

Ubiquiti ES-10X Bedienungsanleitung

Ubiquiti

Ubiquiti PBM3 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-2AC-400-US Bedienungsanleitung

Ubiquiti

Ubiquiti PBE-5AC-300-ISO Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-400-ISO Bedienungsanleitung

Ubiquiti

Ubiquiti U6-MESH Bedienungsanleitung

Ubiquiti

Ubiquiti RocketM Series Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung