Ubiquiti AirMAX PowerBridge M10 PBM10 Bedienungsanleitung

10 GHz Carrier Class

airMAX BaseStation with

Dish Antenna

Model: PBM10

Introduction

Thank you for purchasing the Ubiquiti Networks™

PowerBridge™M. This Quick Start Guide is designed to guide

you through the installation, and show you how to access

the airOS™Configuration Interface. This Quick Start Guide

also includes the warranty terms and is for use with the

PowerBridgeM10, model PBM10.

Package Contents

Radio Dish Feed Mounting

Bracket

Pole Clamps

(Qty. 2)

Stabilizer Brackets

(Qty. 2)

Elevation

Rod

M10x150 Bolts

(Qty. 4)

M10x100 Bolts

(Qty. 2)

M10x25 Bolts

(Qty. 3)

O-Ring

(Installed on feed)

M4x12 Screw and

Washer Assembly

(Qty. 4)

M4x18 Screw and

Washer Assembly

(Qty. 4)

M10 Hex Nuts

(Qty. 9)

M16 Hex Nuts

(Qty. 2)

M10 Washers

(Qty. 9)

M16 Washers

(Qty. 2)

10GHz Carrier Class

airMAXBaseStation with

DishAntenna

Model:PBM 10

M10 Washers

(Qty. 9)

M16 Washers

(Qty. 2)

PoE Adapter

(24V, 1A)

Power Cord Quick Start

Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable is

designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Installation Requirements

• Adjustable wrench or one 16 mm and one 24 mm wrench

• Phillips screwdriver

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial-grade shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Hardware Installation

To install the PowerBridgeM10, perform the following steps:

1. Align the Radio to the back of the Dish.

2. On the front of the Dish, use the four M4x18 Screw and

Washer Assemblies to secure the Radio to the Dish.

3. Connect the Elevation Rod to the back of the Dish using a

M10x25 Bolt, a M10 Washer, a M10 Spring Lock Washer, and

a M10 Hex Nut. Install a M16 Hex Nut about halfway down

on the Elevation Rod and then install a M16 Washer on the

Elevation Rod.

4. Insert the four M10x150 Carriage Bolts into the Mounting

Bracket.

*720-00062-01*

720-00062-01

5. Connect the Mounting Bracket to the Dish:

a. Insert two M10x25 Bolts through the bottom of the

Mounting Bracket and through the Dish. The bolts

should be on the inside facing outward.

b. Secure each bolt using a M10 Washer, a M10 Spring Lock

Washer, and a M10 Hex Nut.

c. Slide the Mounting Bracket onto the Elevation Rod.

d. Secure the Mounting Bracket to the Elevation Rod using

a M16 Washer, a M16 Spring Lock Washer, and a M16

HexNut.

6. Lift the cover on the Radio by pressing down and raising

it up. Connect an Ethernet cable to the Radio and place

the cover back on the Radio. There is an opening for the

Ethernet cable. Slide the cover over the cable.

7. Make sure the O-Ring is secure on the Feed.

O-Ring

8. On the front of the Dish, connect the Feed to the Radio and

Dish using the four M4x12 Screw and Washer Assemblies.

Note: DO NOT handle the assembled unit by the feed

at any time, especially during installation of the Dish

Dish or the brackets

while installing the product.

9. Attach the Stabilizer Brackets to the pole just beneath the

area where the Dish will be attached. Use two M10x100

Bolts, two M10 Washers, two M10 Spring Lock Washers,

and two M10 HexNuts. Tighten the nuts to approximately



Note: The mounting assembly can accommodate a

Ø 1.5" - 4.0" pole.

10. Place the Pole Clamps on the other side of the pole that

the Dish will be mounted on and connect them to the

Mounting Bracket using M10 Washers, M10 Spring Lock

Washers, and M10 Hex Nuts.

11. Adjust the Azimuth and Elevation. Azimuth can be

adjusted by rotating the antenna while supported by the

stabilizer bracket. Elevation is adjusted by loosening the

Elevation Rod. Tighten all bolts and nuts to approximately



Elevation

Azimuth

12. Connect the other end of the Ethernet cable from the

Radio to the Ethernet port labeled POE on the PoE Adapter.

Inhaltsverzeichnis

Andere Ubiquiti Netzwerk-Hardware Handbücher

Ubiquiti

Ubiquiti airVision-C Bedienungsanleitung

Ubiquiti

Ubiquiti AM-5AC21-60 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam M5 Bedienungsanleitung

Ubiquiti

Ubiquiti RD-3G26 Bedienungsanleitung

Ubiquiti

Ubiquiti M900 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Cloud Key Bedienungsanleitung

Ubiquiti

Ubiquiti PBM3 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam AC Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-400-ISO Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-500 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam M PBE-M2-400 Bedienungsanleitung

Ubiquiti

Ubiquiti Loco5AC Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi WiFi BaseStation XG Bedienungsanleitung

Ubiquiti

Ubiquiti UF-AE Bedienungsanleitung

Ubiquiti

Ubiquiti UBB Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam airMAX AC Gen2 PBE-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti mPort-S mPort Serial Bedienungsanleitung

Ubiquiti

Ubiquiti RocketM Series Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-M5-300-IS Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-500-ISO Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti UF-OLT-4 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam airMAX NBE-M5-300 Bedienungsanleitung

Ubiquiti

Ubiquiti ER-4 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung

Ubiquiti airMAX PowerBridge M10 PBM10 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken