Ubiquiti NanoBeam M5 Handbuch

Ubiquity NanoBeam M5 Setup for Truck Scales

1. Purchase the Ubiquity NanoBeam M5 bridge here on Amazon: Nanobeam M5 bridge

2. To access the Nanobeam web interface, your computer must be in the same subnet range as the unit.

3. Click Start, and type Control in the search field, then select Control Panel.

4. Click on Network and Internet.

5. Click on Network and Sharing Center.

6. On the left pane, click the Change adapter settings link.

7. Right-click on your computer’s Ethernet network adapter and select Properties.

8. Select the Internet Protocol Version 4 (TCP/IPv4) option.

9. Click the Properties button.

10. Select the Use the following IP address option.

11. Set the IP address to 192.168.1.1 .

12. Set the Subnet mask. (e.g., 255.255.0.0).

13. Click OK.

14. Click Close again to close the network adapter properties.

15. Connect the truck scale intercom to a POE switch, plug a computer into the POE. Connect the first bridge device

to the POE injector that came with it. Plug the LAN port of that POE injector into the POE Ethernet switch (can

use a non-powered port). Do NOT plug the wireless bridge directly into the same POE Switch as the intercom

since they use different voltages.

16. Launch your web browser. Enter https://192.168.1.20.Press Enter.

17. Log in with username ubnt, password ubnt. Change password to alphaadmin when prompted.

18. Click on the Wireless tab and set Wireless Mode to Access Point.

19. Also under the Wireless tab and Wireless Security, change Security to WPA-AES, WPA Authentication to PSK,

and the WPA Preshared Key to alphaadmin . Click on Change button at the bottom of the screen and the Apply

button at the top of the screen.

20. Go to the Network tab and change IP address to 169.254.1.200 Change Gateway IP to 169.254.1.1. Click on the

Change button at the bottom of the screen and the Apply button at the top of the screen.

21. Connect the scale house phone intercom to a POE switch. Connect the second bridge device to the POE injector

that came with it. Plug the LAN port of that POE injector into the POE Ethernet switch (can use a non-powered

port). Do NOT plug the bridge into the same POE as the phone since they are different voltages. Point the two

bridge devices at each other so they can communicate.

22. Log in to the second unit using the same address and password combination: https://192.168.1.20. username

ubnt, password ubnt

23. Click on the Wireless Tab and make sure Wireless Mode is set to Station.

24. Also under the Wireless tab and Wireless Security, change Security to WPA-AES, WPA Authentication to PSK,

and the WPA Preshared Key to alphaadmin . Click on Change button at the bottom of the screen and the Apply

button at the top of the screen.

25. Go to Network and change IP address to 169.254.1.201. Change Gateway IP to 169.254.1.1. Click on Change

button at the bottom of the screen and the Apply button at the top of the screen.

26. You will now need to reconfigure the Ethernet adapter on your computer with a static IP address on the

169.254.1.1 subnet, subnet mask: 255.255.255.0 if you want to log in to make any changes. The username is

ubnt and the password is alphaadmin. Changing the adapter will also allow you to connect to the intercom

equipment.

27. The equipment should now be operational. For best performance, you should follow the antenna alignment

instructions located here: https://help.ui.com/hc/en-us/articles/205222640-airMAX-How-to-Aim-a-NanoBeam-

for-the-Best-AC-Performance

Andere Handbücher für NanoBeam M5

Inhaltsverzeichnis

Andere Ubiquiti Netzwerk-Hardware Handbücher

Ubiquiti

Ubiquiti airVision-C Bedienungsanleitung

Ubiquiti

Ubiquiti Airmax NBE-M2-400 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-500 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Dream Machine Pro Bedienungsanleitung

Ubiquiti

Ubiquiti airMAX NanoStationM2 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam M Bedienungsanleitung

Ubiquiti

Ubiquiti USW-48-POE Bedienungsanleitung

Ubiquiti

Ubiquiti PBE-5AC-GEN2-5-EU Bedienungsanleitung

Ubiquiti

Ubiquiti ES-10X Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-M5-300-IS Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam M PBE-M2-400 Bedienungsanleitung

Ubiquiti

Ubiquiti USW-Flex-Mini Bedienungsanleitung

Ubiquiti

Ubiquiti U-Installer Bedienungsanleitung

Ubiquiti

Ubiquiti AM-5AC21-60 Bedienungsanleitung

Ubiquiti

Ubiquiti RD-3G26 Bedienungsanleitung

Ubiquiti

Ubiquiti PBM3 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-2AC-400-US Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Dream Machine Pro Bedienungsanleitung

Ubiquiti

Ubiquiti UF-Instant Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam M5 PBE-M5-400 Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket R5AC-Lite Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Cloud Key Gen2 Plus Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi WiFi BaseStation XG Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung