Ubiquiti PBE-5AC-300-ISO Bedienungsanleitung

5 GHz airMAX®ac Bridge with

300 mm RF Isolated Reflector

Model: PBE-5AC-300-ISO

Introduction

Thank you for purchasing the Ubiquiti Networks®

PowerBeam®ac. This Quick Start Guide is designed to guide

you through installation and includes warranty terms.

Package Contents

Reflector Radome Antenna Feed Rear Housing

Mounting Bracket Adjustment

Bracket

Hex Bolts with Washers

(M8x20, Qty. 4)

Pole

Clamp

Carriage Bolts

(M8x135, Qty. 2)

Flange Nuts

(M8, Qty. 2)

Screws with Washers

(M4x12, Qty. 4)

Washers

(M4, Qty. 4)

5GHz airMAX®ac Bridge with

300mm RF Isolated Reflector

Model:PBE-5AC-300-ISO

Nylon Insert

Lock Nuts

(M4, Qty. 4)

Gigabit PoE

(24V, 0.5A) with

Mounting Bracket

Power Cord Quick Start

Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™is

designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Hardware Overview

Bottom View

Cable Door

Rear Housing

Antenna Feed

Ethernet Port

Release

Button Slot

Mounting Bracket

Release Button

Reflector

Alignment Pins

Reset Button

Radome

Technology

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the PowerBeam

is already poweredon. Alternatively, the PowerBeam may be

reset remotely via a Reset button located on the bottom of the

Gigabit PoE adapter.

Release Button After you assemble the PowerBeam, check

the Release button; it should be fully engaged in the Release

Button Slot of the Rear Housing. This ensures that the Antenna

Feed is locked into place. If you need to remove the Antenna

Feed, you must depress the Release button first.

LEDs

Signal In airOS, you can modify the wireless signal

strength threshold values for each LED on the

Advanced tab under Signal LED Thresholds. The

default values are shown below:

LED will light blue when the wireless signal

strength is above -65 dBm.

LED will light blue when the wireless signal

strength is above -73 dBm.

LED will light blue when the wireless signal

strength is above -80 dBm.

LED will light blue when the wireless signal

strength is above -94 dBm.

Ethernet The Ethernet LED will light steady blue

when an active Ethernet connection is made and

flash when there is activity.

Power The Power LED will light blue when the

device is connected to a power source.

Application Examples

The PowerBeam mounted outdoors with the Reflector

installed provides directional outdoor coverage (gain is

reflector-dependent).

The PowerBeam mounted outdoors without the Reflector

installed provides outdoor-to-indoor coverage using the 3 dBi

Antenna Feed only.

Installation Requirements

• 13 mm wrench

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial-grade shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Installation

1. Align and insert the tabs of the Mounting Bracket into

the slots of the Reflector. Rotate the Mounting Bracket

counter-clockwise until the alignment holes in the dish and

bracket align with each other.

2. For added support in high-wind environments, insert four

Screws with Washers into the holes in the Reflector and

Mounting Bracket and secure each screw with a Washer and

a Nylon Insert Lock Nut.

Mounting

Bracket Reflector

3. Line up the Alignment Pins of the Rear Housing with the

alignment holes of the Mounting Bracket. Push the Rear

Housing into the Mounting Bracket.

4. View the Reflector from the front. Ensure that the four

hooks (indicated below) of the Rear Housing are fully

engaged with the inner wall of the Reflector and locked

into place.

Important: Before proceeding, lightly pull the Rear

Housing to confirm that it is locked into place.

5. Push in the sides of the Cable Door and detach it from the

Rear Housing.

6. Attach the Antenna Feed.

a. Insert the Antenna Feed into the Rear Housing, and push

until it locks into place with a click.

b. Lightly pull the Antenna Feed to ensure that it is locked

into place and the Release Button is fully engaged.

Release

Button

Bottom View

7. Connect an Ethernet cable to the Ethernet Port of the

Antenna Feed. Then re-attach the Cable Door to the

RearHousing.

8. Attach the Pole Clamp to the Adjustment Bracket:

a. Hold the Adjustment Bracket with the clamps facing you

and the Elevation Indicator Slot on the left.

b. Insert the Carriage Bolts through the holes of the

Adjustment Bracket.

c. Slide the hole of the Pole Clamp over one bolt of the

Adjustment Bracket.

d. Place one Flange Nut on each bolt.

Elevation

Indicator

Slot

9. Secure the Adjustment Bracket to the Mounting Bracket

using the four Hex Bolts with Washer Set.

10. Position the Reflector assembly on the pole and secure it:

a. Place the Adjustment Bracket against the pole.

b. Slide the slot of the Pole Clamp over the Carriage Bolt.

c. Tighten the Flange Nuts of the bolts to 25 N-m to secure

the antenna to the pole.

25 N-m

Note: The mounting assembly can accommodate a

Ø 40 - 80 mm pole.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Netzwerk-Hardware Handbücher

Ubiquiti

Ubiquiti UniFi UAP Bedienungsanleitung

Ubiquiti

Ubiquiti RocketDish RD-5G30 Bedienungsanleitung

Ubiquiti

Ubiquiti RD-3G26 Bedienungsanleitung

Ubiquiti

Ubiquiti UF-OLT-4 Bedienungsanleitung

Ubiquiti

Ubiquiti UFiber OLT Bedienungsanleitung

Ubiquiti

Ubiquiti ER-4 Bedienungsanleitung

Ubiquiti

Ubiquiti PBM3 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-48-500W Bedienungsanleitung

Ubiquiti

Ubiquiti airVision-C Bedienungsanleitung

Ubiquiti

Ubiquiti UF-LOCO Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Cloud Key Gen2 Plus Bedienungsanleitung

Ubiquiti

Ubiquiti UBB Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi NVR Bedienungsanleitung

Ubiquiti

Ubiquiti airMAX NanoBridge M NBM3 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwtch 5XP Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Dream Machine Pro Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-M5-300-IS Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-24-250W Bedienungsanleitung

Ubiquiti

Ubiquiti NS-5AC Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam M5 Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UBI-POWERBEAM-M5-300 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Cloud Key Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung