Ubiquiti EdgeRouter PoE ERPoe-5 Bedienungsanleitung

5-Port Power over Ethernet

Router

Model: ERPoe-5

Introduction

Thank you for purchasing the Ubiquiti Networks™EdgeRouter™PoE

5-Port Router, which is part of the EdgeMAX™platform. For more

information, visit www.ubnt.com/edgemax

This Quick Start Guide is designed to guide you through

the installation and show you how to access the EdgeOS™

Configuration Interface. This Quick Start Guide also includes the

warranty terms, and is for use with the EdgeRouter PoE, model

ERPoe-5.

Package Contents

EdgeRouter PoE Power Adapter

(24V, 2.5A)

Power Cord

5-Port Power over Ethernet

Router

Model: ERPoe-5

M2.9x20 Screws

(Qty. 2)

M2.9 Anchors

(Qty. 2)

Quick Start Guide

follow local country regulations, including operation within legal frequency channels, output power,

indoor cabling requirements, and Dynamic Frequency Selection (DFS) requirements.

EdgeRouter™PoE Quick Start Guide

Hardware Overview

Front Panel Ports

Console ResetEthernet (eth0-eth4)

Interface Description

Console

RJ45 serial console port for Command Line Interface

(CLI) management. Use a RJ45-to-DB9, serial console

cable, also known as a rollover cable, to connect the

Console port to your computer. (If your computer

does not have a DB9 port, then you will also need a

DB9 adapter.)

Ethernet

(eth0-eth4)

10/100/1000 Mbps ports for routing and PoE. Ports

eth2, eth3, and eth4 can be configured for switching

using the EdgeOS Configuration Interface.

Reset

There are two methods to reset the EdgeRouter PoE

to factory defaults:

• Runtime reset (recommended) The EdgeRouter PoE

should be running after bootup is complete. Press

and hold the Reset button for about 10seconds

until the right LED on port eth4 starts flashing

and then becomes solidly lit. After a few seconds,

the LED will turn off, and the EdgeRouter PoE will

automatically reboot.

• Power-on reset Disconnect the Power Cord from

the Power Adapter. Press and hold the Reset

button while connecting the Power Cord to the

Power Adapter. Keep holding the button until the

right LED on port eth4 starts flashing and then

stops flashing after a few seconds.

Back Panel

Front Panel LEDs

Power Speed/Link/ActPoE

LED State Status

Console

Power

Off Power off

Green Power on

Ethernet (eth0-eth4)

PoE

Off No Power over Ethernet

Green 24V Power over Ethernet

Amber 48V Power over Ethernet*

Speed/

Link/Act

Off No Link

Amber Link Established at 10/100 Mbps

Amber Flashing Link Activity at 10/100 Mbps

Green Link Established at 1000 Mbps

Green Flashing Link Activity at 1000 Mbps

* 48V available when using 48VDC Power Adapter

Back Panel

Power

Grounding Point

Ventilation Holes

EdgeRouter™PoE Quick Start Guide

Hardware Installation

Mount the EdgeRouter PoE on a wall or place it on a bench top.

Note: Keep 20 mm of clearance next to the ventilation

holes for adequate airflow.

Cabling Requirements

• For indoor applications, use Category 5 (or above) UTP cabling

approved for indoor use.

• For outdoor applications, shielded Category 5 (or above) cabling

should be used for all wired Ethernet connections and should

be grounded through the AC ground of the power supply. We

recommend that you protect your outdoor networks from the

most brutal environments and devastating ESD attacks with

industrial‑grade shielded Ethernet cable from Ubiquiti Networks.

For more details, visit www.ubnt.com/toughcable

Note: Although the cabling can be located outdoors,

the EdgeRouter PoE itself should be housed inside a

protective enclosure.

Wall-Mounting

To mount the EdgeRouter PoE on a wall, you will need a drill, a

6mm drill bit, and a Phillips screwdriver.

1. Use a 6 mm drill bit to drill two holes 100 mm apart. (You can

use the template on page 16 to mark the holes.)

2. Insert the M2.9 Anchors into the holes. Use a Phillips screwdriver

to secure a M2.9x20 Screw to each anchor. Leave a clearance of

approximately 3 mm between each screw head and its anchor.

100 mm

3 mm

Note: You can also mount the EdgeRouter PoE

in a vertical orientation.

Hardware Installation

3. Position the EdgeRouter PoE with the Ethernet ports facing

down. Place the Wall-Mount Slots of the EdgeRouter PoE over

the screw heads on the wall. Then slide the EdgeRouter PoE

down to lock it into place.

Grounding the EdgeRouter PoE (Recommended)

The EdgeRouter PoE is grounded through the Power Adapter;

however, you can add optional ESD grounding for enhanced ESD

protection.

1. Loosen the grounding screw to secure a ground wire (not

included) to the Grounding Point.

2. Secure the other end of the ground wire to a grounding block.

EdgeRouter™PoE Quick Start Guide

Connecting Power

1. Connect the Power Adapter to the Power port.

2. Connect the Power Cord to the Power Adapter. Connect the

other end of the Power Cord to a poweroutlet.

Hardware Installation

Accessing the EdgeOS Configuration Interface

1. Connect an Ethernet cable from the Ethernet port of your

computer to the port labeled eth0 on the EdgeRouter PoE.

2. Configure the Ethernet adapter on your host system with a

static IP address on the 192.168.1.x subnet (e.g., 192.168.1.100).

3. Launch your web browser. Type https://192.168.1.1 in the

address field, and press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username

and Password fields. Read the Ubiquiti License Agreement,

and check the box next to I agree to the terms of this License

Agreement to accept it. Click Login.

The EdgeOS Configuration Interface will appear, allowing you to

customize your settings as needed.

EdgeRouter™PoE Quick Start Guide

Configuring PoE Settings

The PoE setting for ports eth0-eth4 is set to Off by default.

WARNING: Before activating PoE, ensure that the connected

device supports passive PoE and the supplied voltage.

1. In the Dashboard tab, click Actions > PoE of the Ethernet port

you want to configure.

2. The Interface Configuration window will appear. Select the

appropriate PoE setting*, and click Save.

The PoE LED on the Ethernet port will confirm the PoE setting.

PoE

Andere Handbücher für EdgeRouter PoE ERPoe-5

Inhaltsverzeichnis

Andere Ubiquiti Netzwerk-Router Handbücher

Ubiquiti

Ubiquiti UniFi Security Gateway PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UFiber UF-WIFI Gebrauchsanweisung

Ubiquiti

Ubiquiti EdgeRouter 4 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBridge M3 Bedienungsanleitung

Ubiquiti

Ubiquiti ER-12 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter 10X Bedienungsanleitung

Ubiquiti

Ubiquiti ROcket M5 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-24-250W Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter LITE Bedienungsanleitung

Ubiquiti

Ubiquiti ER-4 Bedienungs- und Wartungsanleitung

Ubiquiti

Ubiquiti EdgePoint EP-R8 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP PRO Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter Lte 3 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USG Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter PRO Bedienungsanleitung

Ubiquiti

Ubiquiti airCube Bedienungsanleitung

Ubiquiti

Ubiquiti ToughSwitch Pro TS-80-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti LTU LR Bedienungsanleitung

Ubiquiti

Ubiquiti AiAF-5 Bedienungsanleitung

Ubiquiti

Ubiquiti Amplifi AFi-LR Bedienungsanleitung

Ubiquiti

Ubiquiti UFber UF-WIFI Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter ERPro-8 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter 12 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter ER-8 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung