Ubiquiti Edge Pro ERPro-8 Bedienungsanleitung

8-Port Router

with 2 Combination

SFP/RJ45 Ports

Model: ERPro-8

Introduction

Thank you for purchasing the Ubiquiti Networks®

EdgeRouter™PRO, which is part of the EdgeMAX® platform.

Formore information, visit www.ubnt.com/edgemax

This Quick Start Guide is designed to guide you through

installation and show how to access the EdgeOS™

Configuration Interface. This guide also includes the warranty

terms and is for use with the EdgeRouter PRO, modelERPro-8.

Package Contents

EdgeRouter PRO

8-Port Router

with 2 Combination

SFP/RJ45 Ports

Model: ERPro-8

Power Cord Mounting Screws

(#10-32 x 5/8", Qty. 4)

Cage Nuts

(#10-32 x 5/8", Qty. 4)

Quick Start

Guide

responsibility to follow local country regulations, including operation within legal frequency

channels, output power, indoor cabling requirements, and Dynamic Frequency Selection

(DFS) requirements.

Hardware Overview

Front Panel Ports

Console RJ45 (eth0-eth7) SFP (eth6-eth7)

USB

Interface Description

Console

RJ45 serial console port for Command

Line Interface (CLI) management. Use an

RJ45-to-DB9, serial console cable, also

known as a rollover cable, to connect the

Console port to your computer. (If your

computer does not have a DB9 port, then

you will also need a DB9 adapter.) Then

configure the following settings as needed:

• Baud rate 115200

• Data bits 8

• Parity NONE

• Stop bits 1

• Flow control NONE

USB Reserved for future use.

RJ45

(eth0-eth7)

RJ45 ports support 10/100/1000 Ethernet

connections. RJ45 port eth6 or eth7 is

active only if the corresponding SFP port

is empty.

SFP

(eth6-eth7)

SFP ports are hot-swappable and support

100 Mbps or Gigabit fiber SFP modules. If

an SFP module is plugged in, then the SFP

port is active, and the corresponding RJ45

port is deactivated.

Front Panel Button

Reset

Button Description

Reset

There are two methods to reset the

EdgeRouter PRO to factory defaults:

• Runtime reset (recommended) The

EdgeRouter PRO should be running

after bootup is complete. Press and hold

the Reset button for about 10seconds

until the right LED on RJ45 port eth7

starts flashing and then becomes solidly

lit. After a few seconds, the LED will

turn off, and the EdgeRouter PRO will

automatically reboot.

• Power-on reset Disconnect the Power

Cord from the EdgeRouter PRO. Press and

hold the Reset button while connecting

the Power Cord to the EdgeRouter PRO.

Keep holding the button until the right

LED on RJ45 port eth7 starts flashing and

then stops flashing after a few seconds.

Front Panel LEDs

The LEDs on the left side of the RJ45 ports are not used at this

time. Below is a description of the other LEDs:

PowerSFP: Speed/Link/ActRJ45: Speed/Link/Act

LED State Status

RJ45 (eth0-7)

Speed/

Link/Act

Off No Link

Amber Link Established at

10/100Mbps

Amber Flashing Link Activity at

10/100Mbps

Green Link Established at

1000Mbps

Green Flashing Link Activity at

1000Mbps

SFP (eth6-7)

Speed/

Link/Act

Off No Link

Amber Link Established at

10/100Mbps

Amber Flashing Link Activity at

10/100Mbps

Green Link Established at

1000Mbps

Green Flashing Link Activity at

1000Mbps

Power

White EdgeRouter PRO is

poweredon.

Back Panel

Mounting Holes

Power

Ventilation Holes

Mounting Holes

Fans

Note: There are additional ventilation holes on the sides

of the EdgeRouter PRO.

Installation Requirements

• Phillips screwdriver

• Standard-sized, 19" wide rack with a minimum of 1U height

available

• For indoor applications, use Category 5 (or above) UTP

cabling approved for indoor use.

• For outdoor applications, shielded Category 5 (or above)

cabling should be used for all wired Ethernet connections

and should be grounded through the AC ground of the

power supply.

We recommend that you protect your outdoor networks

from the most brutal environments and devastating ESD

attacks with industrial-grade shielded Ethernet cable,

TOUGHCable™, from Ubiquiti Networks. For more details,

visit: www.ubnt.com/toughcable

Note: Although the cabling can be located outdoors,

the EdgeRouter PRO itself should be housed inside a

protective enclosure.

Hardware Installation

1. Connect the Power Cord to the Power port of the

EdgeRouter PRO.

2. Attach the EdgeRouter PRO to the rack using the four

Mounting Screws. (If the rack has square slots, then use the

Cage Nuts with the Mounting Screws.)

Note: Keep 20 mm of clearance next to the

ventilation holes for adequate airflow.

3. Connect the other end of the Power Cord to a power outlet.

Using SFP Ports

To use an SFP port:

1. Remove the protective plug covering the SFP port.

2. Plug a fiber SFP module into the SFP port.

1000Mbps SM/SC 20KM DDM

Tx1550nm/Rx1310nm

SN: 130826179

EF -1 0 00 M -2 0 KM - 15

Note: The corresponding RJ45 port will be deactivated.

3. Connect a fiber optic cable to the fiber SFP module. Then

connect the other end of the cable to another fiber device.

For information about compatible fiber SFP modules, visit:

community.ubnt.com/edgemax

Accessing the EdgeOS Configuration Interface

1. Connect an Ethernet cable from the Ethernet port of your

computer to the port labeled eth0 on the EdgeRouter PRO.

2. Configure the Ethernet adapter on your host system with a

static IP address on the 192.168.1.x subnet.

3. Launch your web browser. Type https://192.168.1.1 in the

address field. Press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username

and Password fields. Read the Ubiquiti License Agreement,

and check the box next to I agree to the terms of this License

Agreement to accept it. Click Login.

The EdgeOS Configuration Interface will appear, allowing

you to customize your settings as needed. You can click the

Wizards tab to access the Setup Wizard.

For more information, refer to the EdgeOS User Guide, which is

available at documentation.ubnt.com/edgemax

Specifications

EdgeRouter PRO

Dimensions 484 x 164 x 44 mm (19.06 x 6.46 x 1.73")

Weight 2.3 kg (5.07 lb)

Max. Power Consumption 40 W

Power Method 110 - 240VAC

Power Supply Internal AC/DC Power Adapter,

60 W (24V, 2.5A)

Button Reset

LED Power

Processor Dual-Core 1 GHz, MIPS64

with Hardware Acceleration

for Packet Processing

System Memory 2 GB DDR3 RAM

Code Storage 4 GB

Certications CE, FCC, IC

Rackmount Yes

ESD/EMP Protection Air: ±24 kV, Contact:± 24 kV

Operating Temperature -10 to 45° C (14 to 113° F)

Operating Humidity 10 - 90% Noncondensing

LEDs Per Port

Serial Console Port N/A

Data Ports Speed/Link/Activity

Networking Interfaces

Serial Console Port (1) RJ45 Serial Port

Data Ports (6) 10/100/1000 RJ45 Ports

(2) 10/100/1000 RJ45/SFP Combination Ports

*640-00094-04*

640-00094-04

Andere Handbücher für Edge Pro ERPro-8

Inhaltsverzeichnis

Andere Ubiquiti Netzwerk-Router Handbücher

Ubiquiti

Ubiquiti EdgeRouter ER-8 Bedienungsanleitung

Ubiquiti

Ubiquiti airCube Bedienungsanleitung

Ubiquiti

Ubiquiti UFber UF-WIFI Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter ER-12P Bedienungsanleitung

Ubiquiti

Ubiquiti UFiber UF-WIFI Gebrauchsanweisung

Ubiquiti

Ubiquiti ER-8-XG Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter 12 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter ERPro-8 Bedienungsanleitung

Ubiquiti

Ubiquiti 3GStation Professional Bedienungsanleitung

Ubiquiti

Ubiquiti ER-12 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter X ER-X Bedienungsanleitung

Ubiquiti

Ubiquiti edgepoint r6 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter ER-10X Bedienungsanleitung

Ubiquiti

Ubiquiti Bullet Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter 10X Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter ER-8 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter X ER-X-SFP Bedienungsanleitung

Ubiquiti

Ubiquiti ERLite-3 Bedienungsanleitung

Ubiquiti

Ubiquiti AiAF-5 Bedienungsanleitung

Ubiquiti

Ubiquiti ER-8-XG Bedienungsanleitung

Ubiquiti

Ubiquiti AFi-ALN Bedienungsanleitung

Ubiquiti

Ubiquiti Amplifi AFi-LR Bedienungsanleitung

Ubiquiti

Ubiquiti ERLite-3 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung