Ubiquiti NanoStation NSM365 Bedienungsanleitung

High-Power 2x2 MIMO

airMAX®TDMA Station

Models: NSM2/NSM3/NSM365/

NSM5/locoM2/locoM5

2x2 MIM

MA Statio

/NSM3/NSM

locoM5

M365/

Introduction

Thank you for purchasing the Ubiquiti Networks®

NanoStation®. This Quick Start Guide is designed to guide you

through installation and also includes warranty terms.

Package Contents

NanoStation Cable Tie

High-Power 2x2 MIMO

airMAX®TDMA Station

Models: NSM2/NSM3/NSM365/

NSM5/locoM2/locoM5

wer

SM2

oM2/

2x2 MIM

MA Statio

/NSM3/NSM

locoM5

M365/

PoE Adapter (24V, 0.5A)

with Mounting Bracket

Power Cord Quick Start

Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™is

designed for outdoor installations. It is the professional installer’s responsibility to follow local

country regulations, including operation within legal frequency channels, output power, and

Dynamic Frequency Selection (DFS) requirements.

Installation Requirements

• Shielded Category 5 (or above) cabling with drain wire

should be used for all wired Ethernet connections and

should be grounded through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit

www.ubnt.com/toughcable

• Surge protection should be used for all outdoor installations.

We recommend that you use two Ethernet Surge Protectors,

model ETH-SP, one near the NanoStation and the other

at the entry point to the building. The ETH-SP will absorb

power surges and safely discharge them into the ground.

Hardware Overview

To LAN

ETH-SP

ES-8-150W

locoM2

Back View

Port Cover Release Button

Mounting

Brackets

LED Panels

NanoStationlocoM2/M5NanoStationM2/M3/M5

LED Panels

LED Panel

Power The Power LED will light green when

the device is connected to a power source.

LAN1 Main Ethernet The LED will light steady green

when an active Ethernet connection is made

to the Main/LAN port and flash when there is

activity.

LAN2

Secondary Ethernet (NanoStation M2/M3/M5

only)

The LED will light steady green when

an active Ethernet connection is made to the

Secondary port and flash when there is activity.

Signal In airOS®, you can modify the wireless

signal strength threshold values for each

LED on the Advanced tab under Signal LED

Thresholds. The default values are shown below:

LED will light red when the wireless

signal strength is above -94 dBm.

LED will light amber when the wireless

signal strength is above -80 dBm.

LED will light green when the wireless

signal strength is above -73 dBm.

LED will light green when the wireless

signal strength is above -65 dBm.

Ports

Main*

Port

Secondary

Port

Reset

Button

Main/LAN 10/100 Ethernet port used to connect the power

and should be connected to the LAN and DHCP server.

Secondary (NanoStationM2/M3/M5 only) 10/100 Ethernet

port used for bridging and supports software-configurable

PoE passthrough.

Note: In order to use PoE passthrough on the Secondary

port, a 24V, 1A PoE adapter is required.

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the NanoStation

LV©SRZHUHGRQ©$OWHUQDWLYHO\©D©UHPRWH©UHVHW©EXWWRQ©LV©ORFDWHG©

on the bottom of the PoE Adapter.

RESET

Switching Gigabit Power Supply / PoE

Reset

Button

* Main is labeled LAN on the NanoStationlocoM2/M5.

*640-00210-05*

640-00210-05

Hardware Installation

1. Press the Port Cover Release Button located on the back of

the NanoStation and slide the cover off.

2. Connect an Ethernet cable to the Main/LAN port.

3. Replace the port cover.

4. Position the NanoStation at the desired location on a pole

and insert a Cable Tie into the slot of the Mounting Bracket.

5. Align the front of the NanoStation toward the other end

of the wireless link. Then tighten the Cable Tie around

WKHSROH

Note: For the NanoStationM2/M3/M5, two Cable Ties

are provided. Fasten the second Cable Tie to the other

mounting bracket for added security.

Connecting Power

Connect the power using one of the following options:

• Using the included Gigabit PoE Adapter: Go to Connecting to

the PoE Adapter.

• Using a separate PoE switch: Connect the Ethernet cable

from the device’s Ethernet port to a PoE-enabled Ethernet

port on the switch.

WARNING: The switch port must comply with the

power specifications listed in the Specifications section

of this Quick Start Guide.

Connecting to the PoE Adapter

1. Connect the Ethernet cable from the device to the POE

port of the PoE Adapter.

2. Connect an Ethernet cable from your LAN to the LAN port

of the PoE Adapter.

3. Connect the Power Cord to the adapter’s power port.

Connect the other end of the Power Cord to a power outlet.

Mounting the PoE Adapter (Optional)

1. Remove the PoE Mounting Bracket from the adapter, place

the bracket at the desired location, and mark the two holes.

2. Pre-drill the holes if necessary, and secure the bracket

using two fasteners (not included).

3. Align the adapter’s slots with the tabs of the PoE Mounting

Bracket©DQG©WKHQ©VOLGH©WKH©DGDSWHUGRZQ

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti LTU-Lite Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP AC Lite Bedienungsanleitung

Ubiquiti

Ubiquiti LTU-Pro Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-PRO-5 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AC AP Mesh Pro Bedienungsanleitung

Ubiquiti

Ubiquiti UNIFI UAP-AC-IW-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-LITE Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam m5 iso PBE-M5-300-ISO Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-nanoHD Bedienungsanleitung

Ubiquiti

Ubiquiti RocketM Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation5 Bedienungsanleitung

Ubiquiti

Ubiquiti UF-Nano Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-LR Bedienungsanleitung

Ubiquiti

Ubiquiti M5 GPS Rocket M Series Bedienungsanleitung

Ubiquiti

Ubiquiti AF-2X Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-AC-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation loco Bedienungsanleitung

Ubiquiti

Ubiquiti NBE-M5-16 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam M5 Bedienungsanleitung

Ubiquiti

Ubiquiti RocketM Series Bedienungsanleitung

Ubiquiti

Ubiquiti NBE-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti airGateway-LR Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung