Ubiquiti UAP-AC-PRO-5 Bedienungsanleitung

802.11ac Pro Access Point

Model: UAP-AC-PRO

Introduction

Thank you for purchasing the Ubiquiti Networks®

UniFi®802.11ac Pro Access Point. This Quick Start Guide is

designed to guide you through installation and includes

warranty terms.

Package Contents

UniFi ac Pro Mounting Bracket Ceiling Backing Plate

Flat Head Screws

(M3x50, Qty. 4)

Keps Nuts

(M3, Qty. 4)

Screws

(M2.9x20, Qty. 4)

802.11acPRO Access Point

Model:UAP-AC-PRO

Screw Anchors

(M3x20, Qty. 4)

Gigabit PoE* (48V, 0.5A)

with Mount Bracket

Power Cord* Quick Start

Guide

* Only the single-pack of the UAP-AC-PRO includes a PoE adapter and

power cord.

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™

is designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Installation Requirements

• Phillips screwdriver

• Drill and drill bit (6 mm for wall-mounting or 3 mm for

ceiling-mounting)

• Optional: Drywall or keyhole saw (to cut 18 mm hole for

Ethernet cable feed)

• Cat5/6 UTP cable for indoor installations

Outdoor Installation Requirements

Important: The UAP-AC-PRO may be installed outdoors

under an eave or other protected location. Do not install

the UniFi AP in an open environment.

• Mounting location should be at least 60 cm (2 ft) from the

edge of the eave or ceiling.

• Cable feed must be pointed downwards when wall-mounted.

• Shielded Category 5 (or above) cabling should be used

for all outdoor wired Ethernet connections and should be

grounded through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit

www.ubnt.com/toughcable

System Requirements

• Microsoft Windows 7/8, MacOSX, or Linux

• Java Runtime Environment 1.6 (or above)

• Web Browser: Mozilla Firefox, Google Chrome, or Microsoft

Internet Explorer 10 (or above)

• UniFi Controller software v4.6 or higher; available for free

download at: downloads.ubnt.com/unifi

Network Topology Requirements

• A DHCP-enabled network (for the AP to obtain an IP address

as well as for the wireless clients after deployment)

• A management station running the UniFi Controller

software, located either on-site and connected to the same

Layer-2 network, or off-site in the cloud or NOC

UAP-AC Outdoor

NetworkHealth

www WAN LAN

WLAN

VOIP

www WAN LAN WLAN VOIP

DNS

GATEWAY

ACTIVECLIENTS

DOWN

SWITCHES

USERS

GUESTS

DOWN

APS

USERS

GUESTS

DOWN

PHONES

EXTENSION

CALLSIN

CALLSOUT

XXX.XXX.XXX.XXX

XXX.XXX.XXX.XXX 192

162

DASHBOARD

MAP

DEVICES

CLIENTS

CALLS

STATISTICS

INSIGHTS

SETTINGS

CURRENTSITE

Default

REFRESHRATE

2minutes

NetworkHealth

www WAN LAN

WLAN

VOIP

www WAN LAN WLAN VOIP

DNS

GATEWAY

ACTIVECLIENTS

DOWN

SWITCHES

USERS

GUESTS

DOWN

APS

USERS

GUESTS

DOWN

PHONES

EXTENSION

CALLSIN

CALLSOUT

XXX.XXX.XXX.XXX

XXX.XXX.XXX.XXX 192

162

DASHBOARD

MAP

DEVICES

CLIENTS

CALLS

STATISTICS

INSIGHTS

SETTINGS

CURRENTSITE

Default

REFRESHRATE

2minutes

O-Site

Cloud/NOC

On-Site

Management

Station

UniFi Switch

UniFi

Security

Gateway

Internet

UAP-AC-PRO UAP-PRO

LAN

WAN

Sample Network Diagram

All UniFi devices support off-site management controllers.

For setup details, see the User Guide on the website:

documentation.ubnt.com/unifi

Hardware Overview

LED

LED Color Status

White Factory default, waiting to be integrated.

Flashing White Initializing.

Alternating

White/Blue

Device is busy; do not touch or unplug it.

This usually indicates that a process such

as a firmware upgrade is taking place.

Blue

Indicates the device has been successfully

integrated into a network and is working

properly.

Quickly

Flashing Blue

This is used to locate an AP.

When you click Locate in the UniFi

Controller software, the AP will flash. It

will also display the location of the AP on

the map.

Steady Blue

with occasional

flashing

Indicates the device is in an isolated state

(all WLANs are brought down until an

uplink is found).

Ports

Main

Port

Secondary

Port

Security

Slot

USB

Port

Reset

Button

Secondary The Secondary port is a Gigabit Ethernet port used

for bridging.

Reset The Reset button serves two functions for the UniFi AP:

• Restart Press and release the Reset button quickly.

• Restore to Factory Default Settings Press and hold the

Reset button for more than five seconds.

USB The USB port is a USB 2.0 port used to support optional

UniFi accessories.

Main The Main port is a Gigabit Ethernet port used to

connect the power and should be connected to the LAN and

DHCPserver.

Note: If you need to remove the UniFi AP from the Mounting

Bracket, insert a paper clip in the Security Slot to release the

Locking Tab and turn the UniFi AP counterclockwise.

Hardware Installation

The UniFi AP can be mounted on the wall or ceiling. Perform

the steps for the appropriate installation:

Wall Mount

1. Position the Mounting Bracket at the desired location on

the wall with the Arrow pointing up.

2. Mark the four mounting holes, and use a 6 mm drill bit to

drill the holes.

Arrow

3. If your Ethernet cable feeds through the wall, cut or drill a

circle approximately 18 mm in diameter (as shown below).

Then feed the CAT5/6 cable through the hole.

Optional 18 mm Hole for

Ethernet Cable Feed through the Wall

4. Insert the Screw Anchors into the 6 mm holes. Secure the

Mounting Bracket to the wall by inserting the Screws into

the anchors.

5. Remove the rubber port cover from the UniFi AP.

6. If the Ethernet cable is fed through the wall, skip to step7.

If the Ethernet cable runs along the mounting surface,

remove the cable feed plug.

7. Feed the Ethernet cable through the port cover.

Note: The feed hole will stretch to accommodate the

RJ45 connector, and then seal around the cable.

8. Connect the Ethernet cable to the Main port and replace

the port cover.

9. Align the Notch on the top edge of the UniFi AP with the

Arrow on the Mounting Bracket.

Lock

Tab

Arrow

Notch

10. Rotate the UniFi AP clockwise until the tabs lock into place

and the Lock Tab engages.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti U-Installer Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam LBE5AC120-U Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-16-120 Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-HD Bedienungsanleitung

Ubiquiti

Ubiquiti airFiber AF-11 Bedienungsanleitung

Ubiquiti

Ubiquiti NBE--2AC--13 Bedienungsanleitung

Ubiquiti

Ubiquiti RocketM Series Bedienungsanleitung

Ubiquiti

Ubiquiti U-LTE Bedienungsanleitung

Ubiquiti

Ubiquiti NBE-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam ac Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-IW-HD Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-AC-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP BeaconHD Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Wifi BaseStationXG Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Bedienungsanleitung

Ubiquiti

Ubiquiti AirFiber X AF-5G34-S45 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam M5-16 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStationM Series Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam AC PBE-5AC-300 Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket R5AC-Lite Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-Outdoor-5 Bedienungsanleitung

Ubiquiti

Ubiquiti M2 GPS Rocket M Series Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi nanoHD Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-Outdoor Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung