Ubiquiti PowerBeam AC GENZ Bedienungsanleitung

5 GHz High‑Performance

airMAX®ac Bridge

Model: PBE‑5AC‑Gen2

Available from A1 Security Cameras

www.a1securitycameras.com email: sales@a1securitycameras.com

Introduction

Thank you for purchasing the Ubiquiti Networks®

PowerBeam®AC Gen 2. This Quick Start Guide is designed to

guide you through installation and includes warranty terms.

Package Contents

Dish Reflector Antenna Feed Rear Housing Adjustment

Bracket

Mounting

Bracket

Hex Bolts with

Washers (Qty. 4)

Pole

Clamp

Long Carriage

Bolts (Qty. 2)

5GHz High‑Performance

airMAX®acBridge

Model:PBE‑5AC‑Gen2

Flange Nuts

(Qty. 2)

Gigabit PoE

(24V, 0.5A) with

Mounting Bracket

Power Cord Quick Start

Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™is

designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Available from A1 Security Cameras

www.a1securitycameras.com email: sales@a1securitycameras.com

Hardware Overview

Bottom View

Technology

Cable Door

Rear Housing

Antenna Feed

Ethernet Port

Release Button Slot

Adjustment Bracket

Release Button

Dish Reflector

Alignment Pins

Reset Button

Carrying Handle/

Lifting Loop

Available from A1 Security Cameras

www.a1securitycameras.com email: sales@a1securitycameras.com

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the PowerBeam

is already poweredon. Alternatively, the PowerBeam may be

reset remotely via a Reset button located on the bottom of the

Gigabit PoE Adapter.

Release Button After you assemble the PowerBeam, check

the Release button; it should be fully engaged in the Release

Button Slot of the Rear Housing. This ensures that the Antenna

Feed is locked into place. If you need to remove the Antenna

Feed, you must depress the Release button first.

LEDs

Power The Power LED will light blue when the

device is connected to a power source.

Ethernet The Ethernet LED will light steady blue

when an active Ethernet connection is made and

flash when there is activity.

Signal In airOS®, you can modify the threshold

value for the wireless signal strength LEDs on the

Wireless tab under Signal LED Thresholds. Each LED

will light when the wireless signal strength is equal

to or greater than the LED’s threshold value. The

default threshold values for these LEDs are shown

below:

-65 dBm -73 dBm -80 dBm -94 dBm

Available from A1 Security Cameras

www.a1securitycameras.com email: sales@a1securitycameras.com

Application Examples

The PowerBeam mounted outdoors with the Dish Reflector

installed provides directional outdoor coverage (gain is

reflector‑dependent).

The PowerBeam mounted outdoors without the Dish Reflector

installed provides outdoor‑to‑indoor coverage using the 3 dBi

Antenna Feed only.

Installation Requirements

• 13 mm wrench

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial‑grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Available from A1 Security Cameras

www.a1securitycameras.com email: sales@a1securitycameras.com

Installation

1. Align and insert the tabs of the Adjustment Bracket into the

slots of the Dish Reflector. Rotate the Adjustment Bracket

counterclockwise until the alignment holes in the dish and

bracket align with each other.

Available from A1 Security Cameras

www.a1securitycameras.com email: sales@a1securitycameras.com

2. Line up the Alignment Pins of the Rear Housing with the

alignment holes of the Adjustment Bracket. Push the Rear

Housing into the Adjustment Bracket.

Note: In high‑wind environments, you can add support

with additional hardware (not included):

1. Using the four holes in the Adjustment Bracket as a

template, drill four holes into the Dish Reflector with a

4.4 mm or 11/64" drill bit.

2. Secure the Dish Reflector to the Adjustment Bracket

using M4 screws, washers, and nuts (not included).

Available from A1 Security Cameras

www.a1securitycameras.com email: sales@a1securitycameras.com

*640-00272-04*

640-00272-04

3. View the Dish Reflector from the front. Ensure that the

three hooks (indicated below) of the Rear Housing are

fully engaged with the inner wall of the Dish Reflector and

locked into place.

IMPORTANT: Before proceeding, lightly pull the Rear

Housing to confirm that it is locked into place.

4. Push in the sides of the Cable Door and detach it from the

Rear Housing.

Available from A1 Security Cameras

www.a1securitycameras.com email: sales@a1securitycameras.com

5. Attach the Antenna Feed.

a. Insert the Antenna Feed into the Rear Housing, and push

until it locks into place with a click.

b. Lightly pull the Antenna Feed to ensure that it is locked

into place and the Release Button is fully engaged.

Release

Button

Bottom View

Available from A1 Security Cameras

www.a1securitycameras.com email: sales@a1securitycameras.com

6. Connect an Ethernet cable to the Ethernet Port of the

Antenna Feed. Then re‑attach the Cable Door to the

RearHousing.

Available from A1 Security Cameras

www.a1securitycameras.com email: sales@a1securitycameras.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti UF-Nano Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-IW Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation 5AC Loco Bedienungsanleitung

Ubiquiti

Ubiquiti UBB Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation M Series Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket 5AC-Lite Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-5AC400 Bedienungsanleitung

Ubiquiti

Ubiquiti UNIFI UAP-AC-IW-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation 5AC Loco Bedienungsanleitung

Ubiquiti

Ubiquiti AirCube ACB-AC Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-16-120 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi nanoHD AP Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Dream Machine Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi XG UAP-XG Bedienungsanleitung

Ubiquiti

Ubiquiti AF-2X Bedienungsanleitung

Ubiquiti

Ubiquiti airFiber AF-11FX Bedienungsanleitung

Ubiquiti

Ubiquiti M900 Bedienungsanleitung

Ubiquiti

Ubiquiti UnFi UAP-AC-LITE Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AC AP Mesh Pro Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP AC EDU Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam M5-16 Bedienungsanleitung

Ubiquiti

Ubiquiti RP5AC-PRISM Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung