Ubiquiti PowerBeam PBE-5AC400 Bedienungsanleitung

High-Performance

Integrated InnerFeed®

airMAX®ac Bridge

Models:

PBE-5AC400

Introduction

Thank you for purchasing the Ubiquiti Networks®

PowerBeam®ac. This Quick Start Guide is designed to guide

you through installation and also includes warranty terms.

The PowerBeam Radome, model PBE-RAD-400, is available as an

optional accessory to enclose the dish reflector. Product details

are available at www.ubnt.com/airmax

Package Contents

Dish Reflector PBE-5AC400

Antenna Feed*

Rear Housing

Dish Bracket Pole Clamp U-Bolt Flange Nuts

(M8, Qty. 2)

High-Performance

IntegratedInnerFeed™

airMAX®acBridge

Models:

PBE-5AC400

Gigabit PoE Adapter

(24V, 0.5A)

with Mounting Bracket

Power Cord Quick Start Guide

* The PBE-5AC400 Antenna Feed has a thin gray ring around the center of

the cap to differentiate it from the PBE-5AC300 Antenna Feed.

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™

is designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Hardware Overview

Bottom View

Cable Door

Rear Housing

Technology

Ethernet Port

Release

Button Slot

Dish Bracket

Release Button

Dish

Reflector

Alignment Pins

Reset Button

Antenna Feed

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the PowerBeam is

already poweredon.

Release Button After you assemble the PowerBeam, check

the Release button; it should be fully engaged in the Release

Button Slot of the Rear Housing. This ensures that the Antenna

Feed is locked into place. If you need to remove the Antenna

Feed, you must depress the Release button first.

LEDs

Signal In airOS, you can modify the wireless signal

strength threshold values for each LED on the

Advanced tab under Signal LED Thresholds. The

default values are shown below:

LED will light blue when the wireless signal

strength is above -65 dBm.

LED will light blue when the wireless signal

strength is above -73 dBm.

LED will light blue when the wireless signal

strength is above -80 dBm.

LED will light blue when the wireless signal

strength is above -94 dBm.

Ethernet The Ethernet LED will light steady blue

when an active Ethernet connection is made and

flash when there is activity.

Power The Power LED will light blue when the

device is connected to a power source.

Application Examples

The PowerBeam mounted outdoors with the Dish Reflector

installed provides directional outdoor coverage (gain is

reflector-dependent).

The PowerBeam mounted outdoors without the Dish Reflector

installed provides outdoor-to-indoor coverage using the 3 dBi

Antenna Feed only.

Installation Requirements

• 13 mm wrench

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial-grade shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Installation

1. Align and insert the tabs of the Dish Bracket into the

slots of the Dish Reflector. Rotate the Dish Bracket

counter-clockwise until the tabs lock into place.

2. Line up the Alignment Pins of the Rear Housing with the

alignment holes of the Dish Bracket. Insert the pins and

push until they lock into place.

*640-00179-01*

640-00179-01

3. Push in the sides of the Cable Door and detach it from the

Rear Housing.

4. Attach the Antenna Feed:

a. Insert the Antenna Feed into the Rear Housing, and push

until it locks into place with a click.

b. Lightly pull the Antenna Feed to ensure that it is locked

into place and the Release button is fully engaged.

Release Button

Bottom View

5. Connect the Ethernet cable:

a. Connect an Ethernet cable to the Ethernet Port of the

Antenna Feed.

b. Re-attach the Cable Door to the Rear Housing.

6. Slide the Pole Clamp onto the Dish Bracket.

7. Insert the U-Bolt into the Pole Clamp and Dish Bracket.Secure

each end of the U-Bolt with a Flange Nut.

25 N-m

Note: The mounting assembly can accommodate a

Ø 32 - 56 mm pole.

8. Optional: If you have the PowerBeam Radome (optional

accessory), then align the arrows on the bottoms of the

Radome and Dish Reflector so the Drain Holes on the Radome

point downward. Snap the Radome onto the Dish Reflector.

Bottom View

9. Connect the other end of the Ethernet cable from the

PowerBeam to the Ethernet port labeled POE on the

Gigabit PoEAdapter.

10. Connect an Ethernet cable from your LAN or computer to

the Ethernet port labeled LAN on the Gigabit PoE Adapter.

11. Connect the Power Cord to the power port on the Gigabit

PoE Adapter. Connect the other end of the Power Cord to a

power outlet.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-LR Bedienungsanleitung

Ubiquiti

Ubiquiti UBB Bedienungsanleitung

Ubiquiti

Ubiquiti U-LTE Bedienungsanleitung

Ubiquiti

Ubiquiti UAP Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi HD nano UAP-HD-NANO Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStationM Series Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AC AP Mesh Pro Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP BeaconHD Bedienungsanleitung

Ubiquiti

Ubiquiti Uni-fi AP Bedienungsanleitung

Ubiquiti

Ubiquiti AirFiber X AF-5G34-S45 Bedienungsanleitung

Ubiquiti

Ubiquiti BULLETM2-HP-US Bedienungsanleitung

Ubiquiti

Ubiquiti LTU-Lite Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket5AC R5AC-PTP Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UNIFI UAP-AC-IW-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam M5 LBE-M5-23 Bedienungsanleitung

Ubiquiti

Ubiquiti Bullet M5 HP Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation5 Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-M Bedienungsanleitung

Ubiquiti

Ubiquiti UF-Nano Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam AC GENZ Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket M2 Titanium RM2-Ti Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket2AC Prism Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung