Ubiquiti PowerBeam PBE-5AC-400-ISO Bedienungsanleitung

ISO

5 GHz airMAX®ac Bridge with

400 mm RF Isolated Reflector

Model: PBE-5AC-400-ISO

Introduction

Thank you for purchasing the Ubiquiti Networks® PowerBeam™ac.

This Quick Start Guide is designed to guide you through

installation and includes warranty terms.

Package Contents

Reflector Radome Antenna

Feed*

Rear Housing

Mounting Bracket Adjustment Bracket Pole Clamp

Hex Bolts with Washers

(M8x20, Qty. 4)

Flange Nuts

(M8, Qty. 2)

Carriage Bolts

(M8x135, Qty. 2)

ISO

5 GHz airMAX®ac Bridge with

400 mm RF Isolated Reflector

Model: PBE-5AC-400-ISO

Gigabit PoE (24V, 0.5A)

with Mounting Bracket

Power Cord Quick Start Guide

* The PBE-5AC-400-ISO Antenna Feed has a thin gray ring around the center

of the cap to differentiate it from the PBE-5AC-300-ISO Antenna Feed.

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™is

designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Hardware Overview

Bottom View

Technology

Cable Door

Rear Housing

Antenna Feed

Ethernet Port

Release Button Slot

Mounting Bracket

Release Button

Reflector

Alignment Pins

Reset Button

Radome

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the PowerBeam

is already poweredon. Alternatively, the PowerBeam may be

reset remotely via a Reset button located on the bottom of the

Gigabit PoE adapter.

Release Button After you assemble the PowerBeam, check

the Release button; it should be fully engaged in the Release

Button Slot of the Rear Housing. This ensures that the Antenna

Feed is locked into place. If you need to remove the Antenna

Feed, you must depress the Release button first.

LEDs

Signal In airOS, you can modify the wireless signal

strength threshold values for each LED on the

Wireless tab under Signal LED Thresholds. The default

values are shown below:

LED will light blue when the wireless signal

strength is above -65 dBm.

LED will light blue when the wireless signal

strength is above -73 dBm.

LED will light blue when the wireless signal

strength is above -80 dBm.

LED will light blue when the wireless signal

strength is above -94 dBm.

Ethernet The Ethernet LED will light steady blue

when an active Ethernet connection is made and

flash when there is activity.

Power The Power LED will light blue when the

device is connected to a power source.

Application Examples

The PowerBeam mounted outdoors with the Reflector

installed provides directional outdoor coverage (gain is

reflector-dependent).

The PowerBeam mounted outdoors without the Reflector

installed provides outdoor-to-indoor coverage using the 3 dBi

Antenna Feed only.

Installation Requirements

• 13 mm wrench

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial-grade shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Installation

1. Align and insert the tabs of the Mounting Bracket into

the slots of the Reflector. Rotate the Mounting Bracket

counterclockwise until the alignment holes in the dish and

bracket align with each other.

2. Line up the Alignment Pins of the Rear Housing with the

alignment holes of the Mounting Bracket. Push the Rear

Housing into the Mounting Bracket.

3. View the Reflector from the front. Ensure that the three

hooks (indicated below) of the Rear Housing are fully

engaged with the inner wall of the Reflector and locked

into place.

Important: Before proceeding, lightly pull the Rear

Housing to confirm that it is locked into place.

4. Push in the sides of the Cable Door and detach it from the

Rear Housing.

5. Attach the Antenna Feed.

a. Insert the Antenna Feed into the Rear Housing, and push

until it locks into place with a click.

b. Lightly pull the Antenna Feed to ensure that it is locked

into place and the Release Button is fully engaged.

Release

Button

Bottom View

6. Connect an Ethernet cable to the Ethernet Port of the

Antenna Feed. Then re-attach the Cable Door to the

RearHousing.

7. Attach the Pole Clamp to the Adjustment Bracket.

a. Hold the Adjustment Bracket with the clamps facing you

and the Elevation Indicators towards the top.

b. Insert the Carriage Bolts through the holes of the

Adjustment Bracket.

c. Slide the hole of the Pole Clamp over one bolt of the

Adjustment Bracket.

d. Place one Flange Nut on each bolt.

Elevation

Indicator

8. Insert the Pivot Pins on the inside of the Adjustment Bracket

into the Mounting Bracket Slots.

Pivot Pin

(one on each side of

Adjustment Bracket)

Mounting

Bracket

Slot

9. Secure the Adjustment Bracket to the Mounting Bracket

using the four Hex Bolts with Washers.

Andere Handbücher für PowerBeam PBE-5AC-400-ISO

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti LiteBeam M5 LBE-M5-23 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Wifi BaseStationXG Bedienungsanleitung

Ubiquiti

Ubiquiti AirOS B2 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AC Mesh Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket5AC R5AC-PTP Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-AC-LR Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi XG UAP-XG Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam AC GENZ Bedienungsanleitung

Ubiquiti

Ubiquiti airFiber AF-5XHD Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi HD nano UAP-HD-NANO Bedienungsanleitung

Ubiquiti

Ubiquiti UF-Nano Bedienungsanleitung

Ubiquiti

Ubiquiti airGateway-LR Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-LITE Bedienungsanleitung

Ubiquiti

Ubiquiti NBE-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket 5AC PTP Bedienungsanleitung

Ubiquiti

Ubiquiti U-LTE Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-IW Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-AC-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi nanoHD Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Dream Machine Beacon Bedienungsanleitung

Ubiquiti

Ubiquiti UBB Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam M Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung