Ubiquiti LiteBeam AC GENZ Bedienungsanleitung

5 GHz airMAX®ac Radio with

InnerFeed®Technology

Model: LBE-5AC-Gen2

Introduction

Thank you for purchasing the Ubiquiti Networks®

LiteBeam®5AC Gen 2 radio. This Quick Start Guide is

designed to guide you through installation and also includes

warrantyterms.

Package Contents

Antenna Feed Center Reflector

Panel

Side Reflector Panels

(Qty. 2)

Feed Receiver Azimuth Mount Elevation Mount Metal Strap

5GHz airMAX®ac Radio with

InnerFeed®Technology

Model:LBE-5AC-Gen2

Wingnut Kit Gigabit PoE* (24V, 0.3A)

with Mounting Bracket

Power Cord* Quick Start

Guide

* Included only in the single-pack of the LBE-5AC-Gen2.

Products may be different from pictures and are subject to change without notice.

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™is

designed for outdoor installations. It is the professional installer’s responsibility to follow local

country regulations, including operation within legal frequency channels, output power, and

Dynamic Frequency Selection (DFS) requirements.

Installation Requirements

• 7 mm socket wrench or screwdriver

• Shielded Category 5 (or above) cabling with drain wire

should be used for all wired Ethernet connections and

should be grounded through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

• Surge protection should be used for all outdoor installations.

We recommend that you use two Ethernet Surge Protectors,

model ETH-SP, one near the LiteBeam and the other at the

entry point to the building. The ETH-SP will absorb power

surges and safely discharge them into the ground.

To LAN

ETH-SP

ES-8-150W

LBE-5AC-Gen2

Application Examples

The LiteBeam AC mounted outdoors with the reflector

installed provides directional outdoor coverage (gain

reflector-dependent).

The LiteBeam AC mounted outdoors without the reflector

installed provides outdoor-to-indoor coverage using the 3 dBi

Antenna Feed only.

Hardware Overview

Bottom View

Antenna Feed

Reector Assembly

Feed Receiver

Azimuth Mount

Elevation Mount

Reset Button

Securing Arms

Port Cover

Ethernet Port

LEDs

Technology

LEDs

Ethernet The LED will light steady blue when an

active Ethernet connection is made and flash when

there is activity.

Power The LED will light blue when the device is

connected to a power source.

Button

Reset To reset to factory defaults, press and hold the Reset

button for more than 10 seconds while the LiteBeamAC is

poweredon. The LiteBeam AC may also be reset remotely

using the auxiliary Reset button located on the bottom of the

Gigabit PoEadapter.

Port

Ethernet Supports 10/100/1000 connections and passive PoE.

This port should be connected to the LAN and DHCP server.

Hardware Installation

The LiteBeam AC was designed for outdoor use and quick

mounting on a pole.

1. Assemble the antenna reflector by attaching the

SideReflector Panels to the Center Reflector Panel:

a. Insert the heads of the two mounting studs on the

Center Reflector Panel into the large opening of the

slotted holes of the Side Reflector Panel.

b. Slide the Side Reflector Panel down until the top edges

of the panels align. The Side Reflector Panel is captured

when both heads of the mounting studs are positioned

over the narrow opening of the slotted holes.

c. Repeat the assembly for the other Side Reflector Panel.

2. Hold the reflector assembly by hand (do not use a tabletop

or flat surface) and insert the Feed Receiver into the

reflector assembly to secure the panels:

a. Align the arrows on the Center Reflector Panel and the

Feed Receiver, and insert both edges of the Side Reflector

Panels and Center Reflector Panels into the Securing Arms

of the Feed Receiver.

b. Insert the Feed Receiver into the Center Reflector Panel by

pressing the top and bottom snap hooks into the slots

of the Center Reflector Panel.

*640-00276-05*

640-00276-05

WARNING: Do not install the Feed Receiver into the

reflector assembly by pushing down onto a tabletop or

other flat surface as this can deform the panels. Hold the

reflector assembly by hand.

c. For additional support, there are eight machine screws

that secure the SideReflector Panels to the antenna

assembly.

3. Insert the Antenna Feed into the Feed Receiver until the feed

locks into place.

4. Turn the Port Cover counterclockwise to reveal the

EthernetPort on the Antenna Feed.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti NanoStation loco Bedienungsanleitung

Ubiquiti

Ubiquiti Uni-fi AP Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Wifi BaseStationXG Bedienungsanleitung

Ubiquiti

Ubiquiti Uni-fi AP Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-IW Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USW-Flex-Mini Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket2AC Prism Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE2ACN Bedienungsanleitung

Ubiquiti

Ubiquiti Power AP N 802.11n Bedienungsanleitung

Ubiquiti

Ubiquiti UBB Bedienungsanleitung

Ubiquiti

Ubiquiti PBE-M5-620 Bedienungsanleitung

Ubiquiti

Ubiquiti UNIFI UAP-AC-IW-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Dream Machine Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-400-ISO Bedienungsanleitung

Ubiquiti

Ubiquiti Loco5AC Bedienungsanleitung

Ubiquiti

Ubiquiti AG-PRO-INS Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti LTU-LR Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Switch Flex Mini Bedienungsanleitung

Ubiquiti

Ubiquiti M900 Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation M2 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi WiFi BaseStationXG UWB-XG-BK Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung